SnO2纳米粒子作为SERS基底的研究

采用溶胶-水热法制备了不同尺寸的SnO2纳米粒子, 并将其作为表面增强拉曼散射(Surface-enhanced Raman scattering, SERS)活性基底, 重点探讨了表面缺陷能级与SERS性能的关系. 观察到4-巯基苯甲酸(4-MBA)吸附在150 ℃水热合成的SnO2纳米粒子上的SERS 信号最强, 随着在空气中煅烧温度的升高, SERS信号逐渐减弱. 分别用透射电子显微镜、 紫外-可见光谱、 荧光光谱、 X射线衍射和X射线光电子能谱对SnO2纳米粒子进行了表征. 结果表明, SnO2纳米粒子的表面氧空位和缺陷等表面性质在增强拉曼散射性能中发挥着重要的作用, 表面氧空位和缺陷等含量越高其SERS信号就越强.     

金属镍掺杂改进纳米TiO2的表面增强拉曼散射性能

通过溶胶-水热法合成纯的和不同量Ni离子掺杂的TiO₂纳米粒子, 将其作为表面增强拉曼散射(SERS)活性基底, 研究了金属Ni掺杂对于纳米TiO₂ SERS性能的改进. 结果表明, 适量的Ni掺杂能够在纳米TiO₂的能隙中靠近导带底的位置形成丰富的掺杂能级, 促进TiO₂-to-molecule的电荷转移过程, 进而提高纳米TiO₂基底对吸附分子的SERS增强能力, 显著改进纳米TiO₂的SERS性能.     

ZnO纳米粒子的表面氧空位与其光致发光和光催化性能的关系

采用沉淀法制备了ZnO纳米粒子, 并利用XPS, SPS, ESR和PL等测试技术对样品进行了表征, 同时评估了样品在光催化氧化气相n-C₇H₁₆中的活性. 重点考察了ZnO纳米粒子的表面组成和结构与其光致发光和光催化性能的关系. 结果表明: ZnO纳米粒子的粒子尺寸越小, 表面氧空位的量越大, 光致发光信号越强, 光催化活性越高. 说明它们之间必然存在一定的关系, 这是因为光致发光信号主要归属于表面氧空位引发的自由和束缚激子发光, 而表面氧空位由于易于捕获光生电子, 且与吸附氧间存在强烈的相互作用, 以至于有利于氧化反应的进行. 此外, 也说明了ZnO纳米粒子的表面态是非常丰富的, 主要是由氧空位和氧物种等引起的.     

Ag纳米粒子在TiO2四棱柱阵列上的可控生长及其SERS效应

采用水热法在导电玻璃FTO导电面上沉积TiO₂四棱柱阵列; 并以其为基体, 分别采用聚乙烯基吡咯 烷酮(PVP)还原Tollens试剂以及柠檬酸三钠(TSC)还原硝酸银溶液, 将Ag纳米粒子(AgNPs)沉积在TiO₂四棱柱阵列上形成TiO₂@AgNPs-PVP和TiO₂@AgNPs-TSC微纳结构作为表面增强拉曼散射(SERS)基底. 实验结果表明, Ag纳米粒子在TiO₂四棱柱阵列上的尺寸和分布可通过改变Tollens试剂的浓度和TSC还原硝酸银溶液的反应时间来调控, 进而优化基底的SERS灵敏度. TiO₂@AgNPs-PVP微纳结构对罗丹明6G(R6G)的检出限为10^-12 mol/L, 对低活性小分子三聚氰胺的检出限为0.01 mg/mL; TiO₂@AgNPs-TSC微纳结构对R6G的检出限为10^-10 mol/L, 对三聚氰胺的检出限为0.01 mg/mL. TiO₂@AgNPs-PVP和TiO₂@AgNPs-TSC微纳结构基底的SERS活性、 循环可回收性与还原剂种类紧密相关: 包覆在Ag纳米粒子上的PVP可以作为隔离层避免Ag纳米粒子直接接触, 防止电磁场耦合作用减弱, 增强基底的SERS活性; 同时, PVP是一种水性聚合物, 有较强的亲水性, 作为循环可回收SERS基底使用时, 吸附小分子物质清洗难度较大.     

多种纳米结构Fe掺杂TiO2光热耦合水分解制氢研究

氧空位是材料缺陷工程的重要组成. 基于光生氧空位的直接热利用, 实现纯水分解制氢的光热耦合实验, 被认为是太阳能综合利用的有效途径. 以多种制备方法合成的TiO₂纳米材料为基础, 研究了多种形貌纳米TiO₂及其Fe掺杂改性材料的光热耦合反应能力. 通过高分辨透射电子显微镜(HRTEM)、 X射线衍射(XRD)和电子顺磁共振(EPR)对晶体特征进行表征, 利用漫反射光谱(DRS)、 光致发光(PL)和三电极测试法表征了材料的性能, 并结合密度泛函理论(DFT)计算了产氢反应路径. 研究结果表明, 溶胶-凝胶法制备的纳米颗粒相比水热法制备的纳米片及纳米线, 体相内缺陷较多, 载流子强度高, 光热耦合产氢效果较差. Fe掺杂改性扩展了光响应, 增强了载流子分离和寿命, 降低了电子传输阻抗, 利于光反应过程中光生氧空位的形成, 克服了制氢反应中的关键能垒. 同时, 纳米材料中的缺陷促进了Fe离子的有效掺杂, Fe掺杂TiO₂纳米颗粒的光热耦合平均产氢量为9.73 μmol/g, 性能提升达13倍.     

ZnO和TiO2纳米粒子的光致发光性能及其与光催化活性的关系

采用沉淀法和溶胶-凝胶法制备了ZnO和TiO2及掺Zn2+的TiO2纳米粒子,用XRD和荧光光谱(FS)等手段对样品进行了表征,重点探讨了样品光致发光机制及与光催化活性的关系.结果表明,ZnO和TiO2样品在大于带隙能的光激发下均表现出明显的FS信号,热处理温度升高,FS信号强度下降,并且二者的FS信号类似,这可能与二者具有类似的电子能带结构有关,同时也说明FS信号主要源于表面氧空位以及吸附氧物种等引起的激子或表面态能级.掺杂Zn2+使TiO2纳米粒子FS信号增强,这主要与表面氧空位和缺陷等量增加有关;此外,在光催化氧化苯酚实验中,样品光催化活性与其FS信号强度顺序一致,即FS信号越强,活性越高.这是由于在光致发光过程中,FS信号主要源于表面氧空位,而在光催化反应中,表面氧空位有利于氧化反应进行.     

氧空位修饰的暴露TiO2{001}的Ru/TiO2增强光热协同CO2甲烷化活性和稳定性

利用太阳能在温和条件下实现CO₂还原反应,不仅可以缓解过度消耗化石能源造成的能源危机,还可以改善诸如温室效应和海洋酸化等环境问题.光热协同催化可以有效降低催化反应温度,具有较大的应用前景.本文利用Ru与暴露TiO₂{001}晶面的TiO₂载体产生的金属-载体相互作用,经过高温氢气煅烧后,获得具有丰富表面氧空位的Ru/TiO₂催化剂.活性测试结果表明,具有丰富表面氧空位的Ru/TiO₂表现出优异的CO₂甲烷化活性,反应过程中甲烷的TOF值在300°C时可以达到22 h-1,但该催化剂却表现出较差的稳定性,在反应10小时后,甲烷的TOF值逐渐降低到19 h-1.将紫外光引入到Ru/TiO₂热催化甲烷化体系中,甲烷的TOF值增加到30 h-1,且兼具高稳定性.热催化反应过程中逐渐消失的表面氧空位和部分氧化的Ru是活性降低的主要原因.在光热协同反应中,光生电子的产生稳定了Ru表面的电子密度,同时也再生了催化剂上表面氧空位,这有效地提高了反应的活性和稳定性.程序升温原位红外和X射线光电子能谱实验结果表明,当催化剂表面具有丰富的表面氧空位时,CO₂可以有效地在Ru纳米粒子上解离成CO中间体,随后吸附在Ru上的CO中间体解离成表面碳物种,并加氢产生甲烷.在热催化反应过程中,Ru纳米粒子逐渐被氧化成Ru Ox物种,且表面氧空位被CO中间物种覆盖,降低了催化反应的稳定性.当紫外光引入到上述反应中,催化剂的表面氧空位可有效提高光生载流子的分离能力.TiO₂载体产生的光电子转移至Ru表面,稳定了金属Ru纳米粒子的价态.另外,载体产生的光生空穴加速了H₂质子化,提高了催化剂对氢气的活化迁移能力,促进了CO中间体的加氢甲烷化反应,进而再生表面氧空位.因此在紫外光照下,兼顾提高了热催化CO₂甲烷化的活性和稳定性.值得注意的是,当Ru负载于暴露少量TiO₂{001}晶面的TiO₂载体上时,产生了强金属-载体相互作用并抑制了H₂在催化剂上的吸附活化,不利于产生表面氧空位.因此暴露少量TiO₂{001}晶面的Ru/TiO₂催化剂也不利于光生载流的产生和分离,这导致热催化或光热协同催化反应活性较低.     

离子液体中铜纳米粒子膜的电沉积制备及表面增强拉曼光谱

采用恒电位方法研究了室温离子液体1-丁基-3-甲基咪唑氟硼酸盐([BMIM]BF₄)中氧化铟锡(ITO)电极表面Cu的沉积过程. 结果表明, Cu²⁺在ITO表面经中间产物Cu⁺还原为Cu. 采用XRD和SEM对不同电位下沉积层的组成和结构进行了考察. 结果表明, 表面组成和结构与沉积电位有关. 在较正电位下沉积所得为Cu/Cu₂O的混合纳米粒子; 在较负电位下为Cu纳米粒子. 随着沉积电位逐渐变负, 其形貌经历了花状、 棒状向球形纳米粒子转变的过程, 且所得沉积膜逐渐变得致密, 其中Cu纳米粒子膜表现出较强的表面增强拉曼散射(SERS)活性, 并且SERS信号均一.     

Au@SiO2膜/Ti电极吸附吡啶的表面增强拉曼光谱研究

基于壳层隔绝纳米粒子增强拉曼光谱技术,合成了Au@SiO₂纳米粒子,并对其进行了相关表征. 结果表明,包裹的二氧化硅层连续、致密,Au@SiO₂膜/Ti电极上可获得金属钛电极上吸附吡啶分子的高质量表面增强拉曼光谱（SERS）信号. 通过Pt、Ni电极的测试,证实该信号源于吸附在基底表面的吡啶分子. 此外,Au@SiO₂膜/Ti电极上吸附吡啶分子的现场SERS光谱研究表明,在-0.1 V ~ -0.6 V电位区间,吡啶分子平躺吸附,从-0.6 V起吸附的吡啶分子由平躺逐转变为垂直,而当电位为-1.2 V时,电极表面析氢,吡啶脱附.     

Pt/H-TiO2催化剂制备及其甲醇电催化氧化性能

以四氯化钛为前驱体,采用水热法合成二氧化钛纳米棒（TiO₂,白色）,在纯H₂气氛,将其550 ^oC热处理2 h,即得有氧缺陷和Ti³⁺填隙原子的二氧化钛纳米棒（H-TiO₂,灰黑色）. 将Pt纳米粒子（~ 1.9 nm）负载于此两种二氧化钛纳米棒上,制得Pt/TiO₂和Pt/H-TiO₂催化剂. XRD和XPS测试表明,氢处理TiO₂晶型没有变化,仍属金红石型,但增加了Ti-OH表面物种. 电化学测试表明,H-TiO₂载体能够增强氧在Pt表面的吸脱附能力,从而提高其甲醇电催化氧化活性,Pt/H-TiO₂电极甲醇氧化峰电流密度为Pt/TiO₂电极的1.6倍、Pt/C电极的2.1倍.     

Effects of surface oxygen vacancies on photophysical and photochemical processes of Zn-doped TiO2 nanoparticles and their relationships

In this paper, TiO(2) nanoparticles doped with different amounts of Zn were prepared by a sol-gel method and were mainly characterized by means of X-ray photoelectron spectroscopy (XPS), photoluminescence (PL), and surface photovoltage spectrum (SPS). The effects of surface oxygen vacancies (SOVs) of Zn-doped TiO(2) nanoparticles on photophysical and photocatalytic processes were investigated along with their inherent relationships. The results show that the SOVs easily bind photoinduced electrons to further give rise to PL signals. The SOVs can result in an interesting sub-band SPS response near the band edge in the TiO(2) sample consisting of much anatase and little rutile, except for an obvious band-to-band SPS response. Moreover, the intensities of PL and SPS signals of TiO(2), as well as the photocatalytic activity for degrading phenol solution, can be enhanced by doping an appropriate amount of Zn. These improvements are mainly attributed to the increase in the SOV amount. It can be suggested that the SOVs should play an important role during the processes of PL, surface photovoltage, and photocatalytic reactions, and, for the as-prepared TiO(2) samples doped with different amounts of Zn by thermal treatment at 550 degrees C, the larger the SOV amount, the stronger the PL and SPS signal, and the higher the photocatalytic activity.     

Relationships of surface oxygen vacancies with photoluminescence and photocatalytic performance of ZnO nanoparticles

ZnO is one of important semiconductor materials,applied widely in the fields such as the cerams, piezo-electric sensors, catalysts and luminescence apparatus.ZnO nanoparticles not only are ideal materials to pre-pare newly electronic apparatus[1], but als…     

Characterization, activity and mechanisms of a visible light driven photocatalyst: Manganese and iron co-modified TiO2 nanoparticles

An attempt was made to prepare Mn,Fe-codoped nanostructured TiO₂ photocatalyst for visible light assisted degradation of an azo dye (methylene blue) in aqueous solutions by a sol-gel process. The asprepared nanoparticles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS) and photoluminescence spectra (PL) techniques. The photocatalytic activity of Mn,Fe-codoped TiO₂ catalyst was evaluated by measuring degradation rates of methylene blue (MB) under visible light. The results showed that doping with the manganese and iron ions significantly enhanced the photocatalytic activity for MB degradation under visible light irradiation. This was ascribed to the fact that a small amount of manganese and iron dopants simultaneously increased MB adsorption capacity and separation efficiency of electron-hole pairs. The results of DRS showed that Mn,Fe-codoped TiO₂ had significant absorption between 400 and 500 nm, which increased with the increase of manganese ion content. It is found that the stronger the PL intensity, the higher the photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions, so that the recombination of photoinduced electrons and holes could be effectively inhibited.     

Room-temperature preparation of nanocrystalline TiO2 films and the influence of surface properties on dye-sensitized solar energy conversion

An extremely easy method is presented for producing surfactant-free films of nanocrystalline TiO2 at room temperature with excellent mechanical stability when deposited on glass or plastic electrodes for dye-sensitized solar energy conversion. Prolonged magnetic stirring of commercial TiO2 nanoparticles (Degussa P25) in either ethanol or water results in highly homogeneous dispersions which are used to prepare TiO2 films with surface properties which depend on the solvent used for dispersing the particles, even after sintering. The optical and mechanical properties of films cast from ethanol and water dispersions are compared, and differences in the extent of surface defects and dye binding are observed. Optical absorption, photoluminescence, and resonance Raman spectra of TiO2 films sensitized with Ru(4,4'-dicarboxylic acid-2,2'-bipyridine)2(NCS)2 ("N3") reveal that the electronic coupling of the dye and semiconductor depends on the surface structure of the film which varies with film preparation. Current-voltage data for illuminated and dark dye-sensitized solar cells are obtained as a function of film preparation, and results are compared to spectroscopic data in order to interpret the microscopic basis for variations in solar cell performance, especially with regard to sintered versus unsintered TiO2 films. The results suggest that surface traps associated with oxygen vacancies play a critical role in determining the efficiency of dye-sensitized solar energy conversion through their influence on the binding and electronic coupling of the dye to the semiconductor.     

The preparation and characterization of La doped TiO2 nanoparticles and their photocatalytic activity

In this paper, pure and La doped TiO₂ nanoparticles with different La content were prepared by a sol-gel process using Ti (OC₄H₉)₄ as raw material, and also were characterized by XRD, TG-DTA, TEM, XPS, DRS and Photoluminescence (PL) spectra. We mainly investigated the effects of calcining temperature and La content on the properties and the photocatalytic activity for degrading phenol of as-prepared TiO₂ samples, and also discussed the relationships between PL spectra and photocatalytic activity as well as the mechanisms of La doping on TiO₂ phase transformation. The results showed that La³⁺ did not enter into the crystal lattices of TiO₂ and was uniformly dispersed onto TiO₂ as the form of La₂O₃ particles with small size, which possibly made La dopant have a great inhibition on TiO₂ phase transformation; La dopant did not give rise to a new PL signal, but it could improve the intensity of PL spectra with a appropriate La content, which was possibly attributed to the increase in the content of surface oxygen vacancies and defects after doping La; La doped TiO₂ nanoparticles calcined at 600°C exhibited higher photocatalytic activity, indicating that 600°C was an appropriate calcination temperature. The order of photocatalytic activity of La doped TiO₂ samples with different La content was as following: 1>1.5>3>0.5>5>0 mol%, which was the same as the order of their PL intensity, namely, the stronger the PL intensity, the higher the photocatalytic activity, demonstrating that there were certain relationships between PL spectra and photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions.     

富表面氧空位Fe2O3/ZnO催化剂在光催化合成氨中的应用

光催化合成氨是一种绿色节能的合成氨技术,设计制造丰富的表面氧空位和异质结构是促进氮分子活化和抑制电子-空穴复合的重要方法。我们以乙二醇作为还原剂,采用溶剂热法制备合成了Fe2O3/ZnO光催化剂,利用X射线衍射(XRD)、透射电镜(TEM)、电子顺磁共振(EPR)、紫外-可见漫反射(UV-Vis DRS)、荧光光谱(PL)及光电流(PC)对Fe2O3/ZnO催化剂进行表征,并考察了Fe2O3/ZnO催化剂在常温、常压下的光催化合成氨的性能。4%Fe2O3/ZnO催化剂在无牺牲剂下用于光催化合成氨,有较好的光催化效率和稳定性,其合成氨效率达到2059μmol·L-1·g-1·h-1。其高催化效率归因于:可见光区域吸收的提高、氮分子在表面氧空位与Fe3+活性中心上的协同活化及光生电子与空穴的高分离效率。     

In situ controlled growth of well-dispersed gold nanoparticles in TiO2 nanotube arrays as recyclable substrates for surface-enhanced Raman scattering

In this paper, well-aligned Au-decorated TiO(2) nanotube arrays with high surface-enhanced Raman scattering (SERS) enhancement were prepared using a facile in situ reduction and controlled growth approach. The gold nanoparticles are well-dispersed and assembled on the mouth surface and the inside of the TiO(2) nanotubes without clogging. The structure and optical properties of the Au-decorated TiO(2) nanotube arrays have been characterized. The Au-decorated TiO(2) nanotube arrays were employed as SERS-active substrates, which exhibit good performance due to long-range coupling between Au nanoparticles, and TiO(2)-assisted enhanced charge-transfer from Au to Rh6G. The SERS activity of the substrates strongly depends on the crystallite size and level of aggregation. The substrates display significant fluorescence quenching ability and uniform SERS responses throughout the whole surface area. Particularly, good recyclability is shown. The photocatalytic property of Au-decorated TiO(2) nanotube array was exploited to recycle the substrate through UV light photocatalytic purification. The experimental results showed that the substrate is featured by high reproducibility and can be used as a highly efficient SERS substrate for multiple detection of different chemical and biological molecules.     

Cu掺杂TiO_2作为SERS基底的研究

本文采用溶胶-水热法制备了TiO2及Cu掺杂的TiO2纳米粒子作为表面增强拉曼光谱(SERS)活性基底,观察到当4-巯基苯甲酸吸附在3%Cu掺杂的TiO2表面上时,其SERS信号得到了最大程度的增强.Cu离子掺杂进TiO2晶格时会使TiO2表面的缺陷浓度(表面态)得到增加,一定量的缺陷浓度对TiO2-to-Molecule的电荷转移机理起到促进作用,进一步证明了化学增强机理在SERS现象的贡献.