掺Sn的纳米TiO2表面光致电荷分离及光催化活性

采用溶胶-凝胶法制备了不同掺Sn量的TiO₂纳米粒子, 主要利用表面光电压谱(SPS)和光致发光光谱(PL)对样品进行了表征, 并通过光催化降解苯酚实验来评估样品活性. 重点考察了热处理温度和掺Sn量对样品表面光生载流子的分离及光催化活性的影响, 并探讨了Sn使TiO₂纳米粒子改性的机制. 结果表明, 在适当温度处理下, 适量Sn的掺入能够有效促进TiO₂纳米粒子表面光生载流子的分离, 以至于使其光催化活性得到显著提高.     

形态结构和光电特性对纳米TiO2光催化性能的影响

采用sol-gel法制备了系列纳米TiO2光催化剂,运用X射线衍射、BET比表面测定、紫外漫反射吸收光谱和表面光电压谱等手段对催化剂进行表征,并以乙烯作为光催化反应的指标反应分子,研究了TiO2纳米晶的性质对于光催化活性的影响.随着焙烧温度的升高,TiO2的晶粒逐渐增大,比表面积下降,晶相由锐钛矿向金红石转变,其吸收带边与光伏响应阈值向长波方向移动,氧化－还原能力降低,降解乙烯的转化率迅速下降.     

Relationships of surface oxygen vacancies with photoluminescence and photocatalytic performance of ZnO nanoparticles

ZnO is one of important semiconductor materials,applied widely in the fields such as the cerams, piezo-electric sensors, catalysts and luminescence apparatus.ZnO nanoparticles not only are ideal materials to pre-pare newly electronic apparatus[1], but als…     

DBS包覆TiO2 纳米粒子的表面光伏及光致发光性能

The TiO2 nanoparticles capped with sodium dodecylbenzenesulfonate (DBS) were synthesized by a sol-hydrothermal method, and were also characterized by XRD, TEM, Surface Photovoltage Spectroscopy (SPS) and Photoluminescence (PL). The effects of capping DBS on photovoltage and photoluminescence performances of TiO2 nanoparticle as well as appropriate capping conditions were principally investigated. The results show that the capping situation is desirable when the pH value and adding DBS amount are in the range of 4.5-5.5 and 1.0%-3.0% of TiO2 weight in advance of the hydrothermal process, respectively. The added DBS could inhibit the growth of anatase crystallite during the hydrothermal process. Moreover, the intensities of SPS and PL of TiO2 nanoparticle decreased after DBS was capped, which is possibly attributed to the electrophilic property of sulfonic acid group (-SO3-) as well as the decrease of surface defect.     

掺Sn的纳米TiO2表面光生束缚激子的验证及其特性

采用溶胶-凝胶法制备了不同掺杂Sn的TiO2纳米粒子，并主要利用表面光电压谱(SPS)和电场诱导表面光电压谱(EFISPS)对样品进行了表征，重点探讨了焙烧温度和掺Sn量对TiO2光生电荷性质的影响．同时揭示了样品结构与表面光生束缚激子的关系及其特性．结果表明：与束缚激子相关的光伏响应只在含有金红石相的TiO2样品中出现，且在混晶相中表现得更加显著．掺杂适量Sn不仅提高了纳米TiO2的与带带跃迁相关的SPS响应强度，同时也使与束缚激子相关的SPS响应明显增强．     

TiO2晶型对Au/TiO2上光催化分解臭氧的影响

以不同晶型TiO2为载体,采用沉积-沉淀法制备了Au/TiO2光催化剂,并用紫外-可见漫反射光谱、X射线光电子能谱(XPS)和表面光电压谱(SPS)等手段进行了催化剂表征,详细考察了Ti O2晶型对Au/TiO2光催化分解臭氧活性的影响.结果表明,光催化分解臭氧的活性顺序为Au/P25>Au/Anatase>Au/Rutile,这与不同的单一Ti O2对光催化臭氧分解的活性顺序是一致的.但在TiO2上沉积金后,其对光催化臭氧的分解活性有了显著的提高.由催化剂的Au4fXPS分析发现,不同晶型Ti O2上的电荷向金簇迁移的能力有明显差异,加之载体本身对光催化臭氧分解活性不同,两者协同作用导致负载金催化剂光催化分解臭氧活性的不同.SPS信号强度与催化剂光催化活性有很好的对应关系,SPS信号越强,光生电子和空穴分离效率越高,光催化活性越好.     

TiO2纳米粒子包覆聚苯乙烯球的结晶性能与表面光电压特性

TiO2具有很高的光催化活性，同时TiO2纳米粒子具有耐酸碱和耐光化学腐蚀、低成本、无毒等性质，在许多领域引起广泛关注．据报道，TiO2的锐钛矿晶型比金红石晶型具有更好的光催化活性．由于金红石是TiO2的热力学稳定相，而锐钛矿是亚稳相，通常锐钛矿相在550-800℃温度范围内形成金红石相，从而降低其催化活性，限制了其应用．     

TiO2纳米粒子膜的制备、表面态性质和光催化活性

在酸性和碱性条件下,用TiCl4水解法制备了TiO2纳米粒子膜催化剂.采用原子力显微镜(AFM),X射线衍射(XRD),表面光电压谱(SPS)和场诱导表面光电压谱(EFISPS)测定了催化剂表面的微结构及能级结构.对催化剂进行了光催化降解苯酚实验,测定了其光催化活性.结果表明,酸性条件下制备的TiO2膜催化剂的光催化活性较高,其结果接近于P25.用能带理论解释了TiO2纳米粒子膜催化剂光催化活性的差异,分析了膜厚对光催化活性的影响.     

掺杂Ce的TiO_2纳米粒子的光致光及其光催化活性

采用sol-gel法制备了纯的和掺杂不同量Ce的TiO_2纳米粒子，并利用XRD， TEM，BET，XPS和PL光谱对样品进行表征，主要考察焙烧温度和含量对掺杂Ce的 TiO_2纳米粒子性质以及光催化降解苯酚活性的影响，并探讨了Ce的掺杂对TiO_2相 变的作用机制以及PL光谱与光催化活性的关系，结果表明，掺杂的Ce~(4+)没有进 入到TiO_2晶格中，而是以小团簇的CeO_2化学态均匀地弥散在TiO_2纳米粒子中， 这可能导致了Ce的掺杂对TiO_2的相变有很大的抑制作用；Ce的掺杂没有引起新的 光致发光现象，而适量Ce的掺杂能够降低TiO_2纳米粒子PL光谱的强度，这是因为 掺杂的Ce~(4+)易于捕获光生电子而生成Ce~(3+);600℃处理的掺杂Ce的TiO_2纳米 粒子表现出较高的光催化活性，这说明600℃是比较合适的焙烧温度，而掺杂不同 量的Ce的TiO_2样品的光催化活性顺序是：3 mol%＞4 mol%＞2 mol%＞5 mol%＞1 mol%＞0 mol%，这与它们的PL光谱强度的顺序是相反的，即PL光谱强度越低，其 光催化活性越高，这说明PL光谱与其光催化活性间有着必然的联系，这是因为掺杂 剂Ce~(4+)能够捕获光生电子，在光致发光过程中使PL光谱强度下降，而在光催化 反应过程中使有机污染物加快氧化。     

Effects of doping La and Cu on photoinduced charge properties of TiO_2 and its relationships with photocatalytic activity

In recent years, nanosized TiO2 materials have been widely studied in photocatalytic and photoelectric conversion fields because of their intrinsic characteris- tics, such as stable chemical property, strong oxidizing capability and nontoxicity[1,2]. And the preparation, characterization and modification of nanosized TiO2 are always crucial contents in semiconductor photo- electric chemistry and photocatalytic researches[3,4]. To further improve TiO2 performance, doping metal ion is consider…     

ZnO和TiO2纳米粒子的光致发光性能及其与光催化活性的关系

采用沉淀法和溶胶-凝胶法制备了ZnO和TiO2及掺Zn2+的TiO2纳米粒子,用XRD和荧光光谱(FS)等手段对样品进行了表征,重点探讨了样品光致发光机制及与光催化活性的关系.结果表明,ZnO和TiO2样品在大于带隙能的光激发下均表现出明显的FS信号,热处理温度升高,FS信号强度下降,并且二者的FS信号类似,这可能与二者具有类似的电子能带结构有关,同时也说明FS信号主要源于表面氧空位以及吸附氧物种等引起的激子或表面态能级.掺杂Zn2+使TiO2纳米粒子FS信号增强,这主要与表面氧空位和缺陷等量增加有关;此外,在光催化氧化苯酚实验中,样品光催化活性与其FS信号强度顺序一致,即FS信号越强,活性越高.这是由于在光致发光过程中,FS信号主要源于表面氧空位,而在光催化反应中,表面氧空位有利于氧化反应进行.     

Effects of simultaneously doped and deposited Ag on the photocatalytic activity and surface states of TiO2

Ag-TiO2 catalysts with different Ag contents were prepared via a sol-gel method in the absence of light. Based on the characterizations of XRD, photoluminescence (PL), surface photovoltage spectroscopy (SPS), field-induced surface photovoltage spectroscopy (FISPS), and XPS as well as the evaluation of the photocatalytic activity for degrading rhodamine B(RhB) solutions, it was found that the Ag dopant promoted the phase transformation as well as had an inhibition effect on the growth of anatase crystallite. The PL and SPS intensities were decreased with increasing Ag content, indicating that the Ag dopant could effectively inhibit the recombination of the photoinduced electrons and holes. However, the active sites capturing the photoinduced electrons reduced, while the Ag content exceeded 5 mol %. At rather low Ag dopant concentrations, the migration and diffusion of Ag+ ions were predominant, while at rather high Ag dopant concentrations, the migration, diffusion, and reduction of Ag ions simultaneously occurred. The Ag-TiO2 photocatalysts with appropriate content of Ag (Ag species concentration is from about 3 to 5 mol %) possessed abundant electron traps so as to be favorable for the separation of the photoinduced electron-hole pairs, which could greatly enhance the activity of the photocatalysts. From the results of FISPS measurements, it could be found that the impurity bands and abundant surface states were introduced into the interfacial layer of TiO2 because of Ag simultaneously doping and depositing, which could improve the absorption capability for visible light of the photocatalysts.     

金红石/锐钛矿混晶结构的TiO2薄膜光催化活性

采用磁控溅射法制备出一组金红石/锐钛矿混晶结构的纳米TiO2薄膜催化剂,并通过光催化降解苯酚实验考察该薄膜的催化性能. 光催化实验证明, 随着催化剂中金红石含量减少, 催化剂的光催化活性逐渐提高. X射线衍射(XRD)、X射线光电子能谱(XPS)、表面光电压谱(SPS)和原子力显微镜(AFM)结果表明, 催化剂为金红石和锐钛矿混晶结构, 并随着金红石含量减少, 催化剂的表面羟基(OH)和桥氧(—O—)的含量逐渐增加, 而且费米能级逐渐提高. 表面羟基和桥氧是有利于光催化的“活性物种”; 费米能级的提高使TiO2/H2O 面处TiO2的表面带弯增大, 导致了价带光生空穴参加光催化反应的几率增大, 有效地促进了光生载流子的分离; 这些因素是催化剂光催化活性逐渐提高的主要原因.     

掺杂Cu的TiO2纳米粒子的制备、表征及其光催化活性

采用Sol-gel法制备了纯的和掺杂不同量Cu的TiO2纳米粒子,并用TG-DTA,XRD,XPS,UV-Vis和荧光光谱对样品进行了表征,考察焙烧温度和Cu含量对TiO2纳米粒子的性质及光催化活性的影响,初步探讨了Cu的掺杂对TiO2相变的作用机制及样品荧光光谱与光催化活性的关系.结果表明,Cu2+的掺杂对TiO2的相变有很大的促进作用,并使其光谱响应范围向可见光区拓展.Cu的掺杂未引起新的荧光现象,但适量Cu的掺杂能够降低TiO2纳米粒子的荧光强度.此外,在光催化降解苯酚的实验中,于500℃处理的掺杂Cu的TiO2纳米粒子的光催化活性较高,与表征结果一致.而掺杂不同量Cu的TiO2的光催化活性顺序与样品荧光光谱强度的顺序相反,即荧光光谱强度越低,其光催化活性越高.     

Multivalency iodine doped TiO2: preparation, characterization, theoretical studies, and visible-light photocatalysis

Multivalency iodine (I(7)+/I(-)) doped TiO(2) were prepared via a combination of deposition-precipitation process and hydrothermal treatment. The as-prepared samples were characterized by X-ray diffraction, transmission electron microscopy, Brunauer-Emmett-Teller surface area, UV-vis diffuse reflectance spectra, X-ray photoelectron spectroscopy, surface photovoltage spectroscopy, and electric-field-induced surface photovoltage spectroscopy. The electronic structure calculations based on the density functional theory revealed that upon doping, new states that originated from the I atom of the IO(4) group are observed near the conduction-band bottom region of TiO(2), and the excitation from the valence band of TiO(2) to the surface IO(4-) is responsible for the visible-light response of the I-doped TiO(2). The as-prepared I-doped TiO(2) showed high efficiency for the photocatalytic decomposition of gaseous acetone under visible light irradiation (lambda > 420 nm). A possible mechanism for the photocatalysis on this multivalency iodine (I(7)+/I(-)) doped TiO(2) under visible light was also proposed.     

ZnO纳米粒子自建场的形成及对其光电特性的影响

The effect of built-in field on the surface photovoltage(SPV) response of ZnO nanoparticles was investigated by means of surface photovoltage spectroscopy(SPS). From the results of in situ SPS in atmosphere and in vacuum, we suggest that the built-in field should be a main condition for producing SPV response. By comparison of SPS with PL in vacuum as well as in atmosphere, we deduce that by changing the ambience of ZnO, its functional properties can be modulated.     

Preparation and characterization of porous TiO_2/ZnO composite nanofibers via electrospinning

<正>Porous TiO_2/ZnO composite nanofibers have been successfully prepared by electrospinning technique for the first time.It was generated by calcining TiO_2/ZnCl_2/PVP[PVP:polyvinyl pyrrolidone)]nanofibers,which were electrospun from a mixture solution of TiO_2,ZnCl_2 and PVP.Transmission electron microscopy(TEM) and X-ray diffraction(XRD) analyses were used to identify the morphology of the TiO_2/ZnO nanofibers and a formation of inorganic TiO_2/ZnO fibers.The porous structure of the TiO_2/ZnO fibers was characterized by N_2 adsoption/desorption isotherm.Surface photovoltage spectroscopy(SPS) and photocatalytic activity measurements revealed advance properties of the porous TiO_2/ZnO composite nanofibers and the results were compared with pure TiO_2 nanofibers,pure ZnO nanofibers and TiO_2/ZnO nanoparticles.     

可见光响应的LaVO4/TiO2 纳米管的合成、表征及对气相甲苯的光催化性能

通过水热方法合成了可见光响应的LaVO4/TiO2纳米管, 采用XRD, TEM, 氮气吸附-脱附以及表面光电压谱对样品进行了表征. 以气相甲苯为典型污染物, 研究了制备样品在可见光(λ＞420 nm)条件下的光催化性能. 实验结果表明, LaVO4的复合使TiO2的粒径减小, 比表面积增大, 光响应范围向可见光偏移. 光催化实验结果表明, 在可见光条件下, LaVO4/TiO2纳米管降解甲苯的效率比其它样品高, 与纯TiO2纳米管相比, 降解效率提高了47%.     

可见光激发下PtⅣClx /TiO2的光诱导电子转移研究

1998年, Kisch等[1]发现PtⅣ卤化物修饰的TiO2催化剂(PtⅣClx/TiO2)具有可见光活性, 他们认为PtⅣ卤化物作为光敏化物种, 能够将电子转移到TiO2导带, 催化剂的表面吸附氧捕获电子后生成氧自由基, 继而氧化降解成对氯苯酚. 但是, 由于PtⅣ卤化物及其激发态能级的不确定, 对其反应机理研究尚未见报道.     

Rup_2P表面敏化TiO_2基复合薄膜光致界面电荷转移

采用离子束溅射技术制备出TiO2/ITO、Zn2+掺杂的TiO2(TiO2-Zn)/ITO和TiO2/ZnO/ITO薄膜,采用表面敏化技术和旋转涂膜法,制备出(1,10-邻菲咯啉)2-2-(2-吡啶基)苯咪唑钌混配配合物(Rup2P)表面敏化的TiO2基复合薄膜Rup2P/TiO2/ITO、Rup2P/TiO2-Zn/ITO和Rup2P/TiO2/ZnO/ITO.表面光电压谱(SPS)结果发现:敏化后的TiO2基薄膜在可见区(400-600nm)产生SPS响应;TiO2基薄膜的能带结构不同,其在400-600nm和350nm处的SPS响应的峰高比不同.利用电场诱导表面光电压谱(EFISPS),测定TiO2基薄膜和表面敏化TiO2基复合薄膜各种物理参数,并确定其能带结构.分析可知,表面敏化TiO2基复合薄膜在400-600nm的SPS响应峰主要源于Rup2P分子的中心离子Ru4d能级到配体1,10-邻菲咯啉π*1和2-(2-吡啶基)苯咪唑π*2能级的跃迁;TiO2中Zn2+掺杂能级有利于Ru4d能级到配体π*1和π*2跃迁的光生电子向TiO2-Zn导带的注入;TiO2/ZnO异质结构有利于光生电子向ITO表面的转移,从而导致可见光(400-600nm)SPS响应增强以及光电转换效率的提高.