Effects of gold catalysts and thermal evaporation method modifications on the growth process of Zn1−xMgxO nanowires

In this paper, we investigate the roles of gold catalysts and thermal evaporation method modifications in the growth process of Zn_1−xMg_xO nanowires. Zn_1−xMg_xO nanowires are fabricated on silicon substrates with and without using a gold catalyst. Characterizations reveal that Mg acts in a self-catalyst role during the growth process of Zn_1−xMg_xO nanowires grown on catalyst-free substrate. The optical properties and crystalline quality of the Zn_1−xMg_xO nanowires are characterized by room temperature photoluminescence (PL) measurements and Raman spectroscopy, respectively. The Raman and PL studies demonstrate that the Zn_1−xMg_xO nanowires grown using the catalyst-free method have good crystallinity with excellent optical properties and have a larger band-gap in comparison to those grown with the assistance of gold.     

Effect of annealing temperature on the structural and optical properties of Zn1−xMgxO particles prepared by oxalate precursor

Zn_1−xMg_xO particles were prepared using zinc and magnesium oxalate precursor by co-precipitated method. The lattice constants of Zn_1−xMg_xO proved that the interstitial Mg formed at 500 °C and Mg replaced Zn in ZnO tetrahedral coordination at 800 °C. Compared with the ZnO, the absorbing band edge of the Zn_1−xMg_xO displayed blue shifts. The room temperature photoluminescence was similar to ZnO and variation of Mg content did not change the shape or peak position of the emission spectra markedly when it was annealed at 500 °C. However, its blue emission band disappeared, and a relatively strong green light emission at 498 nm appeared after annealed at 800 °C. The photoluminescence intensity ratios I_(green)/I_(UV) of Zn_1−xMg_xO varied with Mg content and the green light emission peak shifted from 498 nm to 472 nm when Mg content increased from 0 to 2.0 at.%.     

Effects of Mg doping on the properties of highly transparent conductive and near infrared reflective Zn1−xMgxO:Ga films

Highly transparent conductive and near infrared (IR) reflective Gallium-doped ZnMgO (Zn_1−xMg_xO:Ga) films with Mg content from 0 to 10 at% were deposited on glass substrate by DC reactive magnetron sputtering. X-ray diffraction shows all the ZnMgO:Ga films are polycrystalline and have wurtzite structure with a preferential c-axis orientation. Hall measurements indicate that the resistivity of these films obviously increases with the Mg concentration increasing. The average transmittance of Zn_1−xMg_xO:Ga films is over 90% in the visible range. All the Zn_1−xMg_xO:Ga films have low transmittance and high reflectance in the IR region.     

取向Zn1-xMgxO纳米线阵列的制备及光学特性

采用化学气相沉积(CVD)法, 以高纯ZnO、Mg和活性C混合粉末为原料, 在Si(111)衬底上制备了不同配比的取向Zn1-xMgxO纳米线阵列. 用X射线衍射仪(XRD), 扫描电镜(SEM), 能量色散X射线分析(EDAX)及光致发光(PL)光谱分析仪对样品的晶体结构、形貌、成分组成和光致发光特性进行了分析. 用霍尔效应测量系统测试了不同配比样品的载流子浓度. 实验发现, 当Zn1-xMgxO纳米线阵列中Mg原子相对Zn原子摩尔比x值较小时(x<0.29), XRD衍射谱中只有ZnO晶体标准衍射峰, 没有MgO晶体衍射峰, 说明此时制备的Zn1-xMgxO纳米线样品晶格结构以ZnO纤锌矿结构为主, Mg原子只是作为替位或填隙原子分布在ZnO晶体中. 但当样品中x>0.53时, ZnO与MgO的特征衍射峰同时出现在样品的衍射谱图中, 说明随原料中Mg原子摩尔比的增加, 制备的Zn1-xMgxO纳米阵列样品中ZnO纤锌矿结构与MgO岩盐结构同时存在, 样品呈现多晶体结构形式. 实验还对比了制备的纯ZnO与不同配比的Zn1-xMgxO纳米线阵列的光致发光光谱和载流子浓度, 发现随Mg含量的增加, Zn1-xMgxO阵列紫光发光峰出现了较明显的蓝移现象, 同时, 测试结果也表明, 随Mg含量的增加, Zn1-xMgxO阵列的紫光和绿光峰发光强度都有所减弱, 样品的载流子浓度也随之下降. 文章对实验结果进行了分析和探讨.     

Modulated structure of the composite crystal InCr1−xTixO3+x/2

Incommensurately modulated structure of the composite crystal InCr_1−xTi_xO_3+x/2 was refined by the profile fitting of powder X-ray diffraction based on the four-dimensional superspace group. The crystal consists of two monoclinic subsystems mutually incommensurate in b. The first subsystem is the alternate stacking of an edge-shared InO₆ octahedral layer and a Cr/Ti triangle-lattice plane along c^*. A sheet of oxygen atoms constructing the second subsystem is also extending on the Cr/Ti plane. The whole structure is the alternate stacking of an edge-shared InO₆ octahedral layer and a Cr/Ti-O plane, where displacive modulation of O ions is prominent. Metal ions on the Cr/Ti-O plane are surrounded by three or four oxygen ions on the plane and, in addition, two axial ones.     

Synthesis, Characterization and Humidity Sensitive Properties of Nanocrystalline LaCoxFe1-xO3

The nanocrystalline LaCo_xFe_1-xO₃ with different concentrations of Co was prepared by polyethylene glycol (PEG) sol-gel method and characterized by differential thermal analysis and thermal gravimetric analysis (DTA-TGA), X-ray diffraction (XRD), and scanning electron microscope (SEM). It was found that the crystal structure of perovskite-type could be obtained at 600 °C, and the concentration of Co had significant effects on the solid-state reaction and the average particle size of the obtained nanocrystals. Furthermore, the humidity-sensitive properties of nanocrystalline LaCo_xFe_1-xO₃ were investigated, and it was found that LaCo_0.3Fe_0.7O₃ exhibited higher sensitivity to humidity compared with other samples. The addition of Na₂CO₃ improved the humidity-sensitive properties of this sample, and made its response to humidity good in the whole humidity range of 11%-95% relative humidity (RH).     

Structural and optical properties of ZnMgO nanostructures formed by Mg in-diffused ZnO nanowires

ZnMgO nanostructures with wurtzite phase were prepared by thermal diffusion of Mg into the ZnO nanowires. As ZnO light-emitting devices have been operated by using ZnMgO layers as energy barrier layers to confine the carriers, it is essential to realize the characterization of ZnMgO particularly. In this work, the Mg content in Zn_1−xMg_xO alloy determined by X-ray diffraction (XRD) and photoluminescence (PL) shows a good coincidence. The variation of lattice constant and the blueshift of near-band-edge emission indicate that Zn²⁺ ions are successfully substituted by Mg²⁺ ions in the ZnO lattice. In Raman-scattering studies, the change of E₂(high) phonon line shape in ZnO:Mg nanostructures reveals the microscopic substitutional disorder. In addition to the host phonons of ZnO, two additional bands around 383 and 510 cm⁻¹ are presumably attributed to the Mg-related vibrational modes.     

A novel boron-rich quaternary scandium borocarbosilicide Sc3.67−xB41.4−y−zC0.67+zSi0.33−w

A novel quaternary scandium borocarbosilicide Sc_3.67−xB_41.4−y−zC_0.67+zSi_0.33−w was found. Single crystallites were obtained as an intergrowth phase in the float-zoned single crystal of Sc_0.83−xB_10.0−yC_0.17+ySi_0.083−z that has a face-centered cubic crystal structure. Single crystal structure analysis revealed that the compound has a hexagonal structure with lattice constants a = b = 1.43055(8) nm and c = 2.37477(13) nm and space group (No. 187). The crystal composition calculated from the structure analysis for the crystal with x = 0.52, y = 1.42, z = 1.17, and w = 0.02 was ScB_12.3C_0.58Si_0.10 and that agreed rather well with the composition of ScB_11.5C_0.61Si_0.04 measured by EPMA. In the crystal structure that is a new structure type of boron-rich borides, there are 79 structurally independent atomic sites, 69 boron and/or carbon sites, two silicon sites and eight scandium sites. Boron and carbon form seven structurally independent B₁₂ icosahedra, one B₉ polyhedron, one B₁₀ polyhedron, one irregularly shaped B₁₆ polyhedron in which only 10.7 boron atoms are available because of partial occupancies and 10 bridging sites. All polyhedron units and bridging site atoms interconnect each other forming a three-dimensional boron framework structure. Sc atoms reside in the open spaces in the boron framework structure.     

Synthesis and electrical conductivity of perovskite-type PrCo1−xMgxO3

Oxides in the system PrCo_1−xMg_xO₃ (x=0.0, 0.05, 0.10, 0.15, 0.20, 0.25) were synthesized by citrate technique and characterized by powder X-ray diffraction and scanning electron microscope. All compounds have a cubic perovskite structure (space group ). The maximum ratio of doped Mg in the system PrCo_1−xMg_xO₃ is x=0.2. Further doping leads to the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃. The substitution of Mg for Co improves the performance of PrCoO₃ as compared to the electrical conductivity measured by a four-probe electrical conductivity analyzer in the temperature range from 298 to 1073 K. The substitution of Mg for Co on the B site may be compensated by the formations of Co⁴⁺ and oxygen vacancies. The electrical conductivity of PrCo_1−xMg_xO₃ oxides increases with increasing x in the range of 0.0-0.2. The increase in conductivity becomes considerable at the temperatures ?673 K especially for x?0.1; it reaches a maximum at x=0.2 and 1073 K. From x>0.2 the conductivity of PrCo_1−xMg_xO₃ starts getting lower. This is probably a result of the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃ , which blocks oxygen transport, and association of oxygen vacancies. A change in activation energy for all PrCo_1−xMg_xO₃ compounds (x=0-0.25) was observed, with a higher activation energy above 573 K and a lower activation energy below 573 K. The reasons for such a change are probably due to the change of dominant charge carriers from Co⁴⁺ to Vö in PrCo_1−xMg_xO₃ oxides and a phase transition mainly starting at 573 K.     

Crystal Structure of Pseudorhombohedral InFe1−xTixO3+x/2 (x=2/3)

The structure of pseudorhombohedral-type InFe_1−xTi_xO_3−x/2 (x=2/3) was refined by Rietveld profile fitting. The crystal is a commensurate member of a series in a solution range on InFeO₃-In₂Ti₂O₇ including incommensurate structures. The structure with the unit cell of a=5.9188(1), b=10.1112(2), and c=6.3896(1) Å, β=108.018(2)°, and a space group P2₁/a is the alternate stacking of an edge-shared InO₆ octahedral layer and an Fe/Ti-O plane along c^*. Metal sites on the Fe/Ti-O plane are surrounded by four oxygen atoms on the Fe/Ti-O plane and two axial ones. Electric conductivities of the order 10⁻⁴ S/cm were observed for the samples at 1000 K, while the oxide ion transport number is almost zero as no electromotive force was detected by an oxygen concentration cell.     

Co3−δO4 paracrystal: 3D assembly of nanosize defect clusters in spinel lattice

Paracrystalline array of defect clusters ca. five times the lattice spacing of the average Co_3−δO₄ spinel structure occurred more or less in a relaxed manner when the sintered Co_1−xO polycrystals were air-quenched below the Co_1−xO/Co_3−δO₄ transition temperature to activate oxy-precipitation of cube-like Co_3−δO₄ at dislocations. The same paracrystalline spacing was obtained for Co_3−δO₄ when formed via oxidizing/sintering the Co_1−xO powders at 800°C in air, suggesting a nearly constant δ value for Co_3−δO₄ in the T-P_O2 conditions encountered. The extra cobalt vacancies and Co³⁺ interstitials, as a result of δ value, may form additional 4:1-derived defect clusters for further paracrystalline distribution in the spinel lattice. The nanosize defect clusters self-assembled by columbic interactions and lattice relaxation in ionic crystal may have potential applications as step-wise sensor of oxygen partial pressure at high temperatures.     

Synthesis, crystal structure, and density of (W1−xAlx)C

A new solid solution system of Al in WC, with the stoichiometry of (W_1−xAl_x)C (x=0.10, 0.25, 0.50, 0.75, 0.86), has been synthesized by a solid-state reaction between W_1−xAl_x alloys and carbon at around 1673 K in vacuum. Environment scanning electron microscope, energy-dispersive analysis of X-ray, X-ray photoelectron spectroscopy, and inductively coupled plasma analyses are used to certify the formation of the products. The mechanism of the solid-state reaction is also discussed. (W_1−xAl_x)C is identified to crystallize in the hexagonal space group P6m2 (No. 187) and belongs to the WC structure type. The atoms of W and Al occupy the same lattice site (1a site) in the cell of (W_1−xAl_x)C. The cell parameters for each specimen in the phase of W-Al-C are quite close to that of WC, while their densities are far lower than that of WC.     

Vacancy ordering and oxygen dynamics in oxide ion conducting La1−xSrxGa1−xMgxO3−x ceramics: Ga, Mg and O NMR

The oxygen vacancies distribution in the rigid lattice and the thermally activated motion of oxygen atoms are studied in La_1−xSr_xGa_1−xMg_xO_3−x (x=0.00; 0.05; 0.10; 0.15 and 0.20) compounds. For that ⁷¹Ga, ²⁵Mg and ¹⁷O NMR was performed from 100 K up to 670 K, and ion conductivity measurements were carried out up to 1273 K. The comparison of the electric field gradients at the Ga- and Mg-sites evidences that oxygen vacancies appear exclusively near gallium cations as a species trapped below room temperature in local clusters, GaO_5/2-□-GaO_5/2. These clusters decay at higher temperature into mobile constituents of the structural octahedra Ga(O_5/6□_1/6)_6/2. At the same time, the nearest octahedral oxygen environment of magnesium cations persists at different doping levels. The case of two adjacent vacant anion sites is found highly unlikely within the studied doping range. The thermally activated oxygen motion starts to develop above room temperature as is observed from both the motional narrowing of ¹⁷O NMR spectra and the ¹⁷O nuclear spin-lattice relaxation rate. The obtained results show that two types of motion exist, a slow motion and a fast one. The former is a long-range diffusion whereas the latter is a local back and forth oxygen jumps between two adjacent anion sites. These sites are strongly differentiated by the probability of the vacancy formation, like the vacant apical site and the occupied equatorial site in the orthorhombic compositions x <0.15.     

Preparation of ZnO:CeO2-x thin films by AP-MOCVD: Structural and optical properties

The growth of columnar CeO₂, ZnO and ZnO:CeO_2−x films on quartz and AA6066 aluminum alloy substrates by economic atmospheric pressure metal-organic chemical vapor deposition (AP-MOCVD) is reported. A novel and efficient combination of metal acetylacetonate precursors as well as mild operating conditions were used in the deposition process. The correlation among crystallinity, surface morphology and optical properties of the as-prepared films was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), transmission electron microscopy (TEM) and UV-vis spectroscopy. The synthesized films showed different crystallographic orientations depending on the ZnO and CeO₂ lattice mismatch, cerium content and growth rate. The CeO₂ films synthesized in this work showed plate-like compact structures as a result of the growth process typical of CVD. Both pure and ZnO:CeO_2−x films were obtained with a hexagonal structure and highly preferred orientation with the c-axis perpendicular to both substrates under the optimal deposition conditions. The microstructure was modified from dense, short round columns to round structures with cavities (“rose-flower-like” structures) and the typical ZnO morphology by controlling the cerium doping the film and substrate nature. High optical transmittance (>87%) was observed in the pure ZnO films. As for the ZnO:CeO_2−x films, the optical transmission was decreased and the UV absorption increased, which subsequently was affected by an increase in cerium content. This paper assesses the feasibility of using ZnO:CeO_2−x thin films as UV-absorbers in industrial applications.     

Crystal structure, thermal expansion and conductivity of anisotropic La1−xSrxGa1−2xMg2xO3−y (x=0.05, 0.1) single crystals

Crystal structure and anisotropy of the thermal expansion of single crystals of La_1−xSr_xGa_1−2xMg_2xO_3−y (x=0.05 and 0.1) were measured in the temperature range 300-1270 K. High-resolution X-ray powder diffraction data obtained by synchrotron experiments have been used to determine the crystal structure and thermal expansion. The room temperature structure of the crystal with x=0.05 was found to be orthorhombic (Imma, Z=4, a=7.79423(3) Å, b=5.49896(2) Å, c=5.53806(2) Å), whereas the symmetry of the x=0.1 crystal is monoclinic (I2/a, Z=4, a=7.82129(5) Å, b=5.54361(3) Å, c=5.51654(4) Å, β=90.040(1)°). The conductivity in two orthogonal directions of the crystals has been studied. Both, the conductivity and the structural data indicate three phase transitions in La_0.95Sr_0.05Ga_0.9Mg_0.1O_2.92 at 520-570 K (Imma-I2/a), 770 K (I2/a-R3c) and at 870 K (R3c-R-3c), respectively. Two transitions at 770 K (I2/a-R3c) and in the range 870-970 K (R3c-R-3c) occur in La_0.9Sr_0.1Ga_0.8Mg_0.2O_2.85.     

New synthesis of excellent visible-light TiO2−xNx photocatalyst using a very simple method

An excellent visible-light-responsive (from 400 to 550 nm) TiO_2−xN_x photocatalyst was prepared by a simple wet method. Hydrazine was used as a new nitrogen resource in this paper. Self-made amorphous titanium dioxide precursor powders were dipped into hydrazine hydrate, and calcined at low temperature (110 °C) in the air. The TiO_2−xN_x was successfully synthesized, following by spontaneous combustion. The photocatalyst was characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), transmission electron microscope (TEM), UV-Vis diffuse reflectance spectrometer (DRS), and X-ray photoelectron spectroscopy (XPS). Analysis of XPS indicated that N atoms were incorporated into the lattice of the titania crystal during the combustion of hydrazine on the surface of TiO₂. Ethylene was selected as a target pollutant under visible-light excitation to evaluate the activity of this photocatalyst. The newly prepared TiO_2−xN_x photocatalyst with strong photocatalytic activity and high photochemical stability under visible-light irradiation was firstly demonstrated in the experiment.     

Chemical stability of La1−xSrxCrO3 in oxidizing atmospheres

The single-phase region of La_1−xSr_xCrO₃ (x=0.1, 0.2, 0.3) was precisely determined as a function of temperature, P_O2 and Sr content. The powders with the nominal composition of La_1−xSr_xCrO₃ were equilibrated under various conditions, and then identified by XRD analyses. To confirm the equilibration, two independent experiments were performed for each composition observing (i) the precipitation of the second phase from a single-phase solid solution, and (ii) the formation of the single phase from the constituent oxides. Two kinds of second phases, SrCrO₄ and an unknown phase, were observed depending on the conditions. The second phases tended to appear at low temperature, in high P_O2 and with a large Sr content. The single-phase regions obtained via the two equilibration routes were in good agreement with each other. The thermodynamic calculations on the supposition of ideality of the solid solution essentially reproduced the experimental results. When this material is used as the interconnects of solid oxide fuel cells, much attention should be paid to its relatively narrow solubility range of Sr; for example, the solubility limit is approximately 0.1 under a typical cathode-side condition (1273 K, air).     

Analysis of magnetic and structural phase transition behaviors of La1−xSrxCrO3 for preparation of phase diagram

The phase transition behavior of perovskite-type compounds, La_1−xSr_xCrO₃, was investigated by differential scanning calorimetry (DSC), dilatometry, dc magnetic susceptibility measurement and X-ray diffraction analysis. Both second-order magnetic phase transition from antiferromagnetic to paramagnetic and first-order structural phase transition from orthorhombic to rhombohedral were observed in the DSC or dilatometric curve of every specimen. The temperatures of both these magnetic and structural phase transitions decreased linearly with an increase in Sr content. The structural phase transition temperature of La_1−xSr_xCrO₃ with x less than 0.11 is higher than the magnetic phase transition temperature; however, a larger decrease in structural phase transition temperature than in magnetic phase transition temperature was observed with an increase in Sr content, resulting in a structural phase transition temperature lower than the magnetic phase transition temperature for La_1−xSr_xCrO₃ with x of more than 0.12. It was also observed that the heat of absorption of the structural phase transition decreased with an increase in x. In the dependence of dc magnetic susceptibility on temperature, variations by not only magnetic but also structural phase transitions were observed. It was also revealed that thermal expansion coefficient is affected not only by structural phase transition but also magnetic phase transition. Magnetic and structural phase diagram of La_1−xSr_xCrO₃, suggesting the existence of two Sr contents and temperatures at which triple phases coexist, was proposed.     

Effect of boron non-stoichiometry on B-site in perovskite type structure ScBxRh3 and CeBxRh3 on charges of atoms on A-site: study by X-ray photoelectron and nuclear magnetic resonance spectroscopies

The solid solutions of ScBRh₃-ScRh₃ and CeBRh₃-CeRh₃ are synthesized by the arc melting method, where RBRh₃ and RRh₃ (R=rare earth element) have perovskite and AuCu₃ type structures, respectively. The binding energy of Sc 2p_3/2 for ScB_xRh₃ increases with the boron concentration. The Knight shift of ⁴⁵Sc observed by nuclear magnetic resonance spectroscopy decreases with increase of boron concentration. The decrement of the Knight shift corresponds the Sc 4s electron density at the Fermi level. The intensity ratio of f²: f¹: f⁰ of Ce 3d XPS spectrum changes with boron concentration of CeB_xRh₃. It is concluded that in both cases of ScB_xRh₃ and CeB_xRh₃ the charge on the atoms on A-site changes with the concentration of the atoms on B-site, where the atoms are not directly bound.