Fabrication and Optical Properties of Aligned Zn1-xMgxO Nanowire Arrays

Aligned Zn_1-xMg_xO nanowire arrays were successfully prepared on Si(111) substrates via the chemical vapor deposition (CVD) method with a mixture of ZnO, Mg, and activated carbon powders as reactants. The microstructures and optical properties of the synthesized Zn_1-xMg_xO nanowire arrays were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive analysis X-ray (EDAX), and photoluminescence (PL) spectrum analytic apparatus, respectively. While Mg content was achieved or less approximately 0.29 (x, atomic ratio) in ZnO lattice, the crystal lattice of the synthesized samples exhibited wurtzite structure. The Mg atoms were distributed into the ZnO crystal as the interstitial and displaced atoms, and there was no phase separation in preparing Zn_1-xMg_xO nanowire arrays. However, as the Mg content was up to 0.53 (x) in the fabricated Zn_1-xMg_xO samples, a clear phase separation phenomena appeared in the Zn_1-xMg_xO crystal. Compared with the PL spectrum of the pure ZnO nanowire arrays, the analytic results showed that a blue-shift of the near-band edge emission with increasing Mg content was observed in the Zn_1-xMg_xO arrays. And the relative intensities of green peak at ca 535 nm and UV emission peak at ca 376 nm were all restrained.     

Effects of Mg doping on the properties of highly transparent conductive and near infrared reflective Zn1−xMgxO:Ga films

Highly transparent conductive and near infrared (IR) reflective Gallium-doped ZnMgO (Zn_1−xMg_xO:Ga) films with Mg content from 0 to 10 at% were deposited on glass substrate by DC reactive magnetron sputtering. X-ray diffraction shows all the ZnMgO:Ga films are polycrystalline and have wurtzite structure with a preferential c-axis orientation. Hall measurements indicate that the resistivity of these films obviously increases with the Mg concentration increasing. The average transmittance of Zn_1−xMg_xO:Ga films is over 90% in the visible range. All the Zn_1−xMg_xO:Ga films have low transmittance and high reflectance in the IR region.     

Synthesis and electrical conductivity of perovskite-type PrCo1−xMgxO3

Oxides in the system PrCo_1−xMg_xO₃ (x=0.0, 0.05, 0.10, 0.15, 0.20, 0.25) were synthesized by citrate technique and characterized by powder X-ray diffraction and scanning electron microscope. All compounds have a cubic perovskite structure (space group ). The maximum ratio of doped Mg in the system PrCo_1−xMg_xO₃ is x=0.2. Further doping leads to the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃. The substitution of Mg for Co improves the performance of PrCoO₃ as compared to the electrical conductivity measured by a four-probe electrical conductivity analyzer in the temperature range from 298 to 1073 K. The substitution of Mg for Co on the B site may be compensated by the formations of Co⁴⁺ and oxygen vacancies. The electrical conductivity of PrCo_1−xMg_xO₃ oxides increases with increasing x in the range of 0.0-0.2. The increase in conductivity becomes considerable at the temperatures ?673 K especially for x?0.1; it reaches a maximum at x=0.2 and 1073 K. From x>0.2 the conductivity of PrCo_1−xMg_xO₃ starts getting lower. This is probably a result of the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃ , which blocks oxygen transport, and association of oxygen vacancies. A change in activation energy for all PrCo_1−xMg_xO₃ compounds (x=0-0.25) was observed, with a higher activation energy above 573 K and a lower activation energy below 573 K. The reasons for such a change are probably due to the change of dominant charge carriers from Co⁴⁺ to Vö in PrCo_1−xMg_xO₃ oxides and a phase transition mainly starting at 573 K.     

Preparation of ternary metal chalcogenide (M1-xFexS, M = Cd and Zn) nanocrystallites using single source precursors

M_1−xFe_xS (M = Cd, Zn) nanocrystallites were prepared by pyrolysis and solvothermal decomposition methods using [M(Aftscz)₂] and [M(AftsczH)₂Cl₂] (M = Cd, Zn and AftsczH = monoacetylferrocene thiosemicarbazone) as single source precursors. The M_1−xFe_xS nanocrystallites were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray analysis and UV-Visible spectroscopy. XRD patterns show that the Cd_1−xFe_xS and Zn_1−xFe_xS nanocrystallites prepared by pyrolysis and solvothermal decomposition routes have hexagonal phase. TEM images show presence of spherical and spherical plate-like morphology of M_1−xFe_xS nanoparticles. M_1−xFe_xS nanoparticles obtained by solvothermal decomposition in ethylene glycol are found to be capped with ethylene glycol as evident from IR spectra.     

Crystal Structure of Pseudorhombohedral InFe1−xTixO3+x/2 (x=2/3)

The structure of pseudorhombohedral-type InFe_1−xTi_xO_3−x/2 (x=2/3) was refined by Rietveld profile fitting. The crystal is a commensurate member of a series in a solution range on InFeO₃-In₂Ti₂O₇ including incommensurate structures. The structure with the unit cell of a=5.9188(1), b=10.1112(2), and c=6.3896(1) Å, β=108.018(2)°, and a space group P2₁/a is the alternate stacking of an edge-shared InO₆ octahedral layer and an Fe/Ti-O plane along c^*. Metal sites on the Fe/Ti-O plane are surrounded by four oxygen atoms on the Fe/Ti-O plane and two axial ones. Electric conductivities of the order 10⁻⁴ S/cm were observed for the samples at 1000 K, while the oxide ion transport number is almost zero as no electromotive force was detected by an oxygen concentration cell.     

Solvothermal Synthesis of Superfine Li1−xMn2O4−σ Powders

Superfine Li_1−xMn₂O_4−σ powders were successfully synthesized by the alcohol-thermal method using 0.01 mol of MnO₂, 0.01mol of LiOH·H₂O, and 0.06mol of NaOH as starting materials at 160-200°C. The products are characterized by XRD, TEM, ED, BET, and ICP. Results show that the Li_0.74Mn₂O_3.74 powder prepared at 200°C has an average size of 180 nm with BET surface areas of 16.44 m²/g. A possible formation mechanism is proposed. It was concluded that the alcohol acts not only as the solvent but also as the reducing agent in the synthesis of Li_1−xMn₂O_4−σ powders. The effects of reaction temperature and the contents of NaOH and LiOH on the formation of single phase Li_1−xMn₂O_4−σ were investigated.     

Synthesis, crystal structure, and density of (W1−xAlx)C

A new solid solution system of Al in WC, with the stoichiometry of (W_1−xAl_x)C (x=0.10, 0.25, 0.50, 0.75, 0.86), has been synthesized by a solid-state reaction between W_1−xAl_x alloys and carbon at around 1673 K in vacuum. Environment scanning electron microscope, energy-dispersive analysis of X-ray, X-ray photoelectron spectroscopy, and inductively coupled plasma analyses are used to certify the formation of the products. The mechanism of the solid-state reaction is also discussed. (W_1−xAl_x)C is identified to crystallize in the hexagonal space group P6m2 (No. 187) and belongs to the WC structure type. The atoms of W and Al occupy the same lattice site (1a site) in the cell of (W_1−xAl_x)C. The cell parameters for each specimen in the phase of W-Al-C are quite close to that of WC, while their densities are far lower than that of WC.     

High dielectric constant PrYxOy sensing films electrolyte-insulator-semiconductor pH-sensor for the detection of urea

In this paper, we describe the structural and sensing properties of high-k PrY_xO_y sensing films deposited on Si substrates through reactive co-sputtering. Secondary ion mass spectrometry and atomic force microscopy were employed to analyze the compositional and morphological features of these films after annealing at various temperatures. The electrolyte-insulator-semiconductor (EIS) device incorporating a PrY_xO_y sensing membrane that had been annealed at 800 °C exhibited good sensing characteristics, including a high sensitivity (59.07 mV pH⁻¹ in solutions from pH 2 to 12), a low hysteresis voltage (2.4 mV in the pH loop 7 → 4 → 7 → 10 → 7), and a small drift rate (0.62 mV h⁻¹ in the buffer solution at pH 7). The PrY_xO_y EIS device also showed a high selective response towards H⁺. This improvement can be attributed to the small number of crystal defects and the large surface roughness. In addition, the enzymatic EIS-based urea biosensor incorporating a high-k PrY_xO_y sensing film annealed at 800 °C allowed the potentiometric analysis of urea, at concentrations ranging from 1 to 16 mM, with a sensitivity of 9.59 mV mM⁻¹.     

Enzyme mimics of spinel-type CoxNi1−xFe2O4 magnetic nanomaterial for eletroctrocatalytic oxidation of hydrogen peroxide

A series of spinel-type Co_xNi_1−xFe₂O₄ (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) magnetic nanomaterials were solvothermally synthesized as enzyme mimics for the eletroctrocatalytic oxidation of H₂O₂. X-ray diffraction and scanning electron microscope were employed to characterize the composition, structure and morphology of the material. The electrochemical properties of spinel-type Co_xNi_1−xFe₂O₄ with different (Co/Ni) molar ratio toward H₂O₂ oxidation were investigated, and the results demonstrated that Co_0.5Ni_0.5Fe₂O₄ modified carbon paste electrode (Co_0.5Ni_0.5Fe₂O₄/CPE) possessed the best electrocatalytic activity for H₂O₂ oxidation. Under optimum conditions, the calibration curve for H₂O₂ determination on Co_0.5Ni_0.5Fe₂O₄/CPE was linear in a wide range of 1.0 × 10⁻⁸–1.0 × 10⁻³ M with low detection limit of 3.0 × 10⁻⁹ M (S/N = 3). The proposed Co_0.5Ni_0.5Fe₂O₄/CPE was also applied to the determination of H₂O₂ in commercial toothpastes with satisfactory results, indicating that Co_xNi_1−xFe₂O₄ is a promising hydrogen peroxidase mimics for the detection of H₂O₂.     

Modulated structure of the composite crystal InCr1−xTixO3+x/2

Incommensurately modulated structure of the composite crystal InCr_1−xTi_xO_3+x/2 was refined by the profile fitting of powder X-ray diffraction based on the four-dimensional superspace group. The crystal consists of two monoclinic subsystems mutually incommensurate in b. The first subsystem is the alternate stacking of an edge-shared InO₆ octahedral layer and a Cr/Ti triangle-lattice plane along c^*. A sheet of oxygen atoms constructing the second subsystem is also extending on the Cr/Ti plane. The whole structure is the alternate stacking of an edge-shared InO₆ octahedral layer and a Cr/Ti-O plane, where displacive modulation of O ions is prominent. Metal ions on the Cr/Ti-O plane are surrounded by three or four oxygen ions on the plane and, in addition, two axial ones.     

Analysis of magnetic and structural phase transition behaviors of La1−xSrxCrO3 for preparation of phase diagram

The phase transition behavior of perovskite-type compounds, La_1−xSr_xCrO₃, was investigated by differential scanning calorimetry (DSC), dilatometry, dc magnetic susceptibility measurement and X-ray diffraction analysis. Both second-order magnetic phase transition from antiferromagnetic to paramagnetic and first-order structural phase transition from orthorhombic to rhombohedral were observed in the DSC or dilatometric curve of every specimen. The temperatures of both these magnetic and structural phase transitions decreased linearly with an increase in Sr content. The structural phase transition temperature of La_1−xSr_xCrO₃ with x less than 0.11 is higher than the magnetic phase transition temperature; however, a larger decrease in structural phase transition temperature than in magnetic phase transition temperature was observed with an increase in Sr content, resulting in a structural phase transition temperature lower than the magnetic phase transition temperature for La_1−xSr_xCrO₃ with x of more than 0.12. It was also observed that the heat of absorption of the structural phase transition decreased with an increase in x. In the dependence of dc magnetic susceptibility on temperature, variations by not only magnetic but also structural phase transitions were observed. It was also revealed that thermal expansion coefficient is affected not only by structural phase transition but also magnetic phase transition. Magnetic and structural phase diagram of La_1−xSr_xCrO₃, suggesting the existence of two Sr contents and temperatures at which triple phases coexist, was proposed.     

Effect of annealing temperature on the structural and optical properties of Zn1−xMgxO particles prepared by oxalate precursor

Zn_1−xMg_xO particles were prepared using zinc and magnesium oxalate precursor by co-precipitated method. The lattice constants of Zn_1−xMg_xO proved that the interstitial Mg formed at 500 °C and Mg replaced Zn in ZnO tetrahedral coordination at 800 °C. Compared with the ZnO, the absorbing band edge of the Zn_1−xMg_xO displayed blue shifts. The room temperature photoluminescence was similar to ZnO and variation of Mg content did not change the shape or peak position of the emission spectra markedly when it was annealed at 500 °C. However, its blue emission band disappeared, and a relatively strong green light emission at 498 nm appeared after annealed at 800 °C. The photoluminescence intensity ratios I_(green)/I_(UV) of Zn_1−xMg_xO varied with Mg content and the green light emission peak shifted from 498 nm to 472 nm when Mg content increased from 0 to 2.0 at.%.     

Preparation of ZnO:CeO2-x thin films by AP-MOCVD: Structural and optical properties

The growth of columnar CeO₂, ZnO and ZnO:CeO_2−x films on quartz and AA6066 aluminum alloy substrates by economic atmospheric pressure metal-organic chemical vapor deposition (AP-MOCVD) is reported. A novel and efficient combination of metal acetylacetonate precursors as well as mild operating conditions were used in the deposition process. The correlation among crystallinity, surface morphology and optical properties of the as-prepared films was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), transmission electron microscopy (TEM) and UV-vis spectroscopy. The synthesized films showed different crystallographic orientations depending on the ZnO and CeO₂ lattice mismatch, cerium content and growth rate. The CeO₂ films synthesized in this work showed plate-like compact structures as a result of the growth process typical of CVD. Both pure and ZnO:CeO_2−x films were obtained with a hexagonal structure and highly preferred orientation with the c-axis perpendicular to both substrates under the optimal deposition conditions. The microstructure was modified from dense, short round columns to round structures with cavities (“rose-flower-like” structures) and the typical ZnO morphology by controlling the cerium doping the film and substrate nature. High optical transmittance (>87%) was observed in the pure ZnO films. As for the ZnO:CeO_2−x films, the optical transmission was decreased and the UV absorption increased, which subsequently was affected by an increase in cerium content. This paper assesses the feasibility of using ZnO:CeO_2−x thin films as UV-absorbers in industrial applications.     

Thermal and photochemical effects on the structure,morphology, thermal and optical properties of PVA/Ni0.04Zn0.96O and PVA/Fe0.03Zn0.97O nanocomposite films

Ni_0.04Zn_0.96O and Fe_0.03Zn_0.97O with average diameter of 23 and 19 nm, respectively, have been synthesized by a modified sol–gel method to be used in the preparation of (100 − x)/x poly(vinyl alcohol)/oxide nanocomposite films, with x = 0, 1, 3 and 5 (in wt.%). A 125 W-Hg vapor lamp with emission above 254 nmwas used to irradiate PVA/Ni_0.04Zn_0.96O and PVA/Fe_0.03Zn_0.97O films. The effect on their structural, thermal, morphological and optical properties was studied by TG, DSC, DRX, AFM, UV–vis and PL spectrophotometry. The Ni_0.04Zn_0.96O addition on PVA films decreases the thermal stability of the polymer in inert and in oxidative atmosphere. In contrast, the Fe_0.03Zn_0.97O presence in the PVA films seems to increase the thermal stability of the polymer. The characteristic peak of the crystalline phase of PVA and wurtzite phase of the zinc oxide were identified through X-ray diffraction in both films. The crystallinity of the PVA film increases with UV irradiation and with the presence of Ni_0.04Zn_0.96O and Fe_0.03Zn_0.97O. The roughness of the PVA film was not modified by the addition of the doped oxides; however, it increases after UV irradiation, more significantly in the films containing the oxides. The PVA film exhibits absorption around 280 nm characteristic of π–π^∗ transitions related to carbonyl groups from residuals acetate, while the 95/05 PVA/Ni_0.04Zn_0.96O and 95/05 PVA/Fe_0.03Zn_0.97O nanocomposite films show absorption at the visible region which is characteristics of the band gap reduction of the doped oxides. The photoluminescence of PVA was modified by the presence of the oxides in the film. These nanocomposite films are interesting due to their thermal, mechanical (flexible) properties and low cost of production. In addition they are also able to exhibit peculiar optical properties showing potential to be used in photonic devices, gas sensors and organic solar cell applications.     

Synthesis, optical properties and electronic structures of polyoxometalates K3P(Mo1−xWx)12O40 (0?x?1)

Various compositions of solid solutions K₃P(Mo_1−xW_x)₁₂O₄₀ (0?x?1) were prepared using two solid state synthetic routes. The crystallite size was determined by linewidth refinements of X-ray diffraction patterns using the Warren-Averbach method, and the grain size distribution by laser scattering experiments. Optical properties were determined by diffuse reflectance measurements in the UV-visible range. The optical gap E_g was found to increase exponentially from ∼2.5 to ∼3.30 eV with increasing x, and is systematically shifted to a higher energy when the grain size decreases. The relation between E_g and x was analyzed by calculating the HOMO-LUMO gaps of the [P(Mo_1−xW_x)₁₂O₄₀]³⁻ anions on the basis of tight-binding electronic structure calculations.     

Hydrothermal crystal growth of the potassium niobate and potassium tantalate family of crystals

Single crystals of KNbO₃ (KN), KTaO₃ (KT), and KTa_1−xNb_xO₃ (x=0.44, KTN) have been prepared by hydrothermal synthesis in highly concentrated KOH mineralizer solutions. The traditional problems of inhomogeneity, non-stoichiometry, crystal striations and crystal cracking resulting from phase transitions associated with this family compounds are minimized by the hydrothermal crystal growth technique. Crystals of good optical quality with only minor amounts of metal ion reduction can be grown this way. Reactions were also designed to provide homogeneous distribution of tantalum and niobium metal centers throughout the KTN crystal lattice to maximize its electro-optic properties. Synthesis was performed at relatively low (500-660 °C) temperatures in comparison to the flux and Czochralski techniques. This work represents the largest crystals of this family of compounds grown by hydrothermal methods to date.     

Chemical stability of La1−xSrxCrO3 in oxidizing atmospheres

The single-phase region of La_1−xSr_xCrO₃ (x=0.1, 0.2, 0.3) was precisely determined as a function of temperature, P_O2 and Sr content. The powders with the nominal composition of La_1−xSr_xCrO₃ were equilibrated under various conditions, and then identified by XRD analyses. To confirm the equilibration, two independent experiments were performed for each composition observing (i) the precipitation of the second phase from a single-phase solid solution, and (ii) the formation of the single phase from the constituent oxides. Two kinds of second phases, SrCrO₄ and an unknown phase, were observed depending on the conditions. The second phases tended to appear at low temperature, in high P_O2 and with a large Sr content. The single-phase regions obtained via the two equilibration routes were in good agreement with each other. The thermodynamic calculations on the supposition of ideality of the solid solution essentially reproduced the experimental results. When this material is used as the interconnects of solid oxide fuel cells, much attention should be paid to its relatively narrow solubility range of Sr; for example, the solubility limit is approximately 0.1 under a typical cathode-side condition (1273 K, air).     

Charge compensation and oxidation in NaxCoO2−δ and LixCoO2−δ studied by XANES

A comparative study on the oxidation and charge compensation in the A_xCoO_2−δ systems, A=Na (x=0.75, 0.47, 0.36, 0.12) and Li (x=1, 0.49, 0.05), using X-ray absorption spectroscopy at O 1s and Co 2p edges is reported. Both the O 1s and Co 2p XANES results show that upon removal of alkali metal from A_xCoO_2−δ the valence of cobalt increases more in Li_xCoO_2−δ than in Na_xCoO_2−δ. In addition, the data of O 1s XANES indicate that charge compensation by oxygen is more pronounced in Na_xCoO_2−δ than in Li_xCoO_2−δ.     

A reagentless DNA biosensor based on cathodic electrochemiluminescence at a C/CxO1−x electrode

A reagentless signal-on electrochemiluminescence (ECL) biosensor for DNA hybridization detection was developed based on the quenching effect of ferrocene (Fc) on intrinsic cathodic ECL at thin oxide covered glassy carbon (C/C_xO_1−x) electrodes. To construct the DNA biosensor, molecular beacon (MB) modified with ferrocene (3′-Fc) was attached to a C/C_xO_1−x electrode via the covalent bound between labeled amino (5′-NH₂) and surface functional groups. It was found that the immobilization of the probe on the electrode surface mainly depended on the fraction of surface carbonyl moiety. When a complementary target DNA (cDNA) was present, the stem-loop of MB on the electrode was converted into a linear double-helix configuration due to hybridization, resulting in the moving away of Fc from the electrode surface, and the restoring of the cathodic ECL signal. The restoration of the ECL intensity was linearly changed with the logarithm of cDNA concentration in the range of 1.0 × 10⁻¹¹ to 7.0 × 10⁻⁸ M, and the detection limit was ca. 5.0 pM (S/N = 3). Additionally, single-base mismatched DNA can be effectively discriminated from the cDNA. The great advantage of the biosensor lies in its simplicity and cost-effective with ECL generated from the electrode itself, and no adscititious luminophore is required.     

The electronic structure of the CuRh1−xMgxO2 thermoelectric materials: An X-ray photoelectron spectroscopy study

A detailed X-ray photoelectron spectroscopy study has been performed for the CuRh_1−xMg_xO₂ (x=0, 0.04 and 0.10) series for a better understanding of the role of the Mg²⁺ substitution on the electrical properties and the value of the Seebeck coefficient. This study is based on an analysis of different compounds such as Rh₂O₃, Sr₂RhO₄ and CuCrO₂ in order to characterize different oxidation states (Rh³⁺ and Rh⁴⁺ in octahedral oxygen environment and Cu⁺ in a dumbbell O-Cu-O coordination). The Cu2p signal of copper in the non-doped compounds CuCrO₂ and CuRhO₂ reveals different electronic structures. An evolution of the Cu2p core signal with the increase of Mg²⁺ content in the CuRh_1−xMg_xO₂ is highlighted by XPS. The differences observed, especially for the Cu2p core peaks are discussed for the non-doped compounds CuCrO₂ and CuRhO₂ as for the CuRh_1−xMg_xO₂ series upon Mg²⁺ substitution.