聚甲基乙撑碳酸酯/氧化石墨烯纳米复合材料的制备及性能研究

本文采用改进Hummers法制备氧化石墨烯(GO),通过原子力显微镜对GO片层形貌进行表征;以聚甲基乙撑碳酸酯(PPC)、聚乙烯醇(PVA)和氧化石墨烯(GO)为原料,采用溶液和熔融共混法相结合,制备PPC/PVA/GO纳米复合材料,研究其力学性能、热学性能和动态流变行为。结果表明,当GO含量为0.5 wt%时,拉伸强度达到了22.03 MPa,与纯PPC相比提高了25.8%;当GO含量增大到1.0 wt%时,拉伸强度开始降低;断裂伸长率随GO的加入呈现降低的趋势。GO含量为1.0%时复合材料的热学性能最好,与纯PPC相比,复合材料的完全热分解温度从350℃提高到了400℃以上,并且热分解速率下降了12%/min;复合材料的复数黏度、储能模量和损耗模量随PVA及GO的引入也有一定程度的提高。     

改性氧化石墨烯稳定Pickering乳液法制备高导热相变整体材料

采用表面引发原子转移自由基聚合法(SI-ATRP)改性氧化石墨烯(GO), 并用其稳定Pickering高内相乳液, 一步成型制得高导热氧化石墨烯/石蜡复合整体相变材料. 通过SI-ATRP方法, 在氧化石墨烯表面引入分子刷, 提高GO的分散性, 实现了低GO含量下优异的导热强化效果. 当GO添加量仅为相变复合材料整体的0.4%(质量分数)时, 其热导率(3.968 W?m^-1?K^-1)比纯石蜡的热导率(0.608 W?m^-1?K^-1)有较大提升. 通过测试发现, 在1000次循环后相变材料的泄漏率仅为1.1%~1.3%, 表现出良好的形状稳定性和热可靠性. 制备的新型形状稳定相变材料在温控、 储能应用中具有潜在的用途.     

AOPAN/PA-66复合纳米纤维膜的制备及对金属离子的吸附性能

采用双喷头电纺丝技术,将尼龙(PA-66)纤维增强的聚丙烯腈(PAN)纳米纤维膜(PAN/PA-66)与盐酸羟胺进行偕胺肟化反应,制备了一种偕胺肟化聚丙烯腈/尼龙复合纳米纤维膜(AOPAN/PA-66).通过红外光谱及扫描电子显微镜等方法研究了偕胺肟化前后纳米纤维膜的组成、形貌和力学性能;并考察了AOPAN/PA-66复合纳米纤维膜对铜离子和铅离子的吸附性能.结果表明,AOPAN/PA-66复合纳米纤维膜的抗拉伸强度及断裂伸长率分别为4.73 MPa和30.76%,对Cu(Ⅱ)及Pb(Ⅱ)的吸附量分别为67.5和75.4 mg/g.     

氧化石墨烯增容尼龙6/聚苯乙烯共混体系的研究

氧化石墨烯(GO)亲水性的边缘和疏水性的中间片层使其具有两亲特性.利用GO的这种特性,将其加入尼龙6(PA6)/聚苯乙烯(PS)的共混体系,以提高PA6和PS的相容性.通过两步法制备了PA6/PS/GO共混物,研究了GO对PA6/PS共混材料结构形态与力学性能的影响,并对其增容机理进行了探讨.扫描电镜(SEM)结果表明,添加GO后,共混材料的分散相尺寸明显变小,分散更为均匀,少量的GO即可达到良好的增容效果.动态力学性能(DMA)测试进一步证明了GO对PA6/PS共混物具有一定的增容性.理论计算也表明PS/GO共混物和PA6具有更接近的表面自由能和较低的界面自由能.添加GO后共混物材料的拉伸性能和韧性明显提高.GO添加量为0.1 wt％时,共混材料的断裂伸长率较未添加GO的共混材料提高了170％,断裂能也提高了近240％.     

氧化石墨烯改性ZnO/CeO2复合纳米材料的制备及其紫外屏蔽性能研究

以六水硝酸锌、六水硝酸铈、氧化石墨烯为原料,采用溶胶凝胶法制备了氧化石墨烯(GO)改性ZnO/CeO_2复合纳米紫外屏蔽剂。采用X射线衍射(XRD)、扫描电镜(SEM)、傅立叶变换红外光谱(FTIR)、紫外可见分光光度计(UV-Vis)等测试手段对产物的结构、组成及形貌进行表征,研究了氧化铈与氧化锌摩尔比、GO投入量、屏蔽剂用量以及pH值对复合纳米材料紫外屏蔽性能的影响,探索了氧化石墨烯改性ZnO/CeO_2复合纳米的最佳制备条件。结果表明:氧化石墨烯改性ZnO/CeO_2复合纳米材料中GO、CeO_2、ZnO的平均粒径分别为8. 3、15. 4、37. 5 nm。当pH 6. 0、氧化铈与氧化锌摩尔比为4∶1、GO投入量为2. 0g、屏蔽剂用量为0. 06 g/L时,紫外屏蔽性能强弱顺序为:氧化石墨烯改性ZnO/CeO_2复合纳米材料 GOZnO/CeO_2复合纳米材料 CeO_2 ZnO。     

聚丙烯腈/纳米掺锑SnO_2复合导电材料的制备及性能研究

采用超声波辅助溶液共混的方式制备了聚丙烯腈(PAN)/纳米掺锑SnO_2(ATO)复合材料,采用扫描电镜(SEM)、广角X衍射(WXRD)、动态力学分析仪(DMA)及热失重分析仪(TGA)研究了复合材料的微观相态结构、动态力学性能及热性能,对复合材料的导电性能进行了测试.结果表明:经过钛酸酯偶联剂处理的纳米ATO在PAN基体中分散良好;纳米ATO的加入可以有效地提高PAN的导电性能,当其质量分数为8%时,复合材料电导率可达10~(-4)S/cm;添加纳米ATO后PAN的储存模量及玻璃化转变温度提高;PAN/ATO复合材料的热稳定性与纯PAN相比明显提高.     

掺杂羧基化碳纳米管的纳米碳纤维前驱体的制备及表征

为获得结构完整、 性能优良的纳米碳纤维前驱体, 采用静电纺丝法制备了掺杂羧基化多壁碳纳米管(MWCNTs)的聚丙烯腈(PAN)纳米纤维. 用扫描电子显微镜、 偏振红外光谱、 透射电子显微镜、 拉曼光谱及拉伸性能测试等对杂化纳米纤维的微观结构和力学性能进行了研究, 分析了MWCNTs含量的影响. 实验结果表明, 5%(质量分数)的MWCNTs掺杂量为杂化纳米纤维直径的突变点, 且MWCNTs的加入有利于PAN分子链的取向, MWCNTs在PAN纤维中大体上沿纤维轴向取向分布. 3%MWCNTs/PAN杂化纳米纤维的拉伸强度和拉伸模量分别达到88.6 MPa和3.21 GPa.     

乙醇胺功能化石墨烯及其PVB复合材料的制备

采用乙醇胺对石墨烯进行改性,一步合成了乙醇胺功能化石墨烯(EFG),探讨了实验条件对该过程的影响.结果表明,乙醇胺在对石墨烯进行功能化的同时还能起到还原氧化石墨烯(GO)的作用,反应产物的吸光度随着乙醇胺的用量、反应温度、反应体系pH值和反应时间的增加而增加,而产物中N元素的含量则随之减小,最佳合成条件为:乙醇胺与GO的质量比为4.0,反应温度50℃,体系pH 7.0,反应时间12 h.然后分别采用溶液共混法和原位还原法,制备了两种不同的EFG/聚乙烯醇缩丁醛(PVB)复合材料,研究了EFG的添加量和加入方式对PVB性能的影响.结果表明,EFG的引入可以极大的提高PVB的导电率、紫外线屏蔽能力和力学性能,且采用原位还原法的效果更好.当EFG添加量为3.0 wt%时,复合材料的导电率较PVB升高了约6~7个数量级;当EFG的添加量仅为1.0 wt%时,复合材料对紫外线的屏蔽能力就到达了90%以上.     

静电纺丝制备石墨烯基复合纳米纤维研究进展

在静电纺丝纳米纤维中加入纳米填料——石墨烯(G),有助于提高纳米纤维的性能,扩展其应用领域。本文综述了近年来国内外静电纺丝制备石墨烯基复合纳米纤维的研究现状,重点介绍了石墨烯与聚酰胺(PA)、聚甲基丙烯酸甲酯(PMMA)、聚丙烯腈(PAN)、二氧化钛(TiO2)等复合纳米纤维制备的研究进展及其在光催化剂、超级电容器、染料敏化太阳能电池(DSSCs)、传感器、生物医学等方面的应用潜力,展望了石墨烯基复合纳米纤维的发展前景。     

AOPAN@PAN同轴纳米纤维的制备及吸附性能

将盐酸羟胺与聚丙烯腈(PAN)反应得到偕胺肟化聚丙烯腈(AOPAN)溶液,随后采用同轴静电纺丝技术,制备了以AOPAN为壳,PAN为芯的同轴纳米纤维(AOPAN@PAN).通过透射电子显微镜(TEM)、扫描电子显微镜(SEM)和红外光谱(FTIR)等对纤维的形貌、组成和力学性能进行了表征.结果表明,随着PAN用量的增加,AOPAN@PAN同轴纳米纤维的强度逐渐变大,当芯层与壳层质量比为1∶3时,纳米纤维的抗拉伸强度和断裂伸长率分别为3.677 MPa和18.03%;对Cu~(2+),Pb~(2+),CrO_4~(2-)和甲基橙(MO)的最大吸附量分别为135.1,151.2,120.48和43.45 mg/g;使水中Cu~(2+),Pb~(2+),CrO_4~(2-)和MO的浓度分别降低到0.17,0.03,0.06和0.91 mg/L.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.