预还原氢化物发生-原子荧光光谱法快速测定化探样品中的As、Sb、Bi、Hg

通过对化探样品进行王水密闭溶解,饱和的硫脲-抗坏血酸预还原,运用氢化物发生-原子荧光光谱法实现了地质样品中As、Sb、Bi、Hg元素的任意配对以及连续快速测定。实验确定了原子化器高度为14mm,最佳溶样时间为1h。在优化条件下,结果显示还原剂(硫脲-抗坏血酸)对Hg、Bi测定结果无影响,且Hg、Bi测定结果在预还原20min至48h内都很稳定,测定结果良好,Cu、Co、Ni、Au、Ag、Cd、As、Sb、Bi、Se、Ge等金属离子对预还原测定汞均无干扰,对比实验表明还原剂体系下汞荧光强度值基本不变。方法的检出限低、精密度好、准确度高、操作简便,有效避免了元素污染问题,可满足大批量地质样品分析测定的需要。     

氢化物发生-原子荧光光谱法测定1：5万区域地质调查样品中的As、Sb、Bi、Hg等4种元素

建立了氢化物发生-原子荧光光谱法测定1∶5万区域地质调查样品中的As、Sb、Bi、Hg等4种元素的分析方法,通过采用王水(1+1)分解样品,在盐酸(5%)介质中用硼氢化钾作为还原剂对As、Sb、Bi、Hg等4种元素进行氢化物发生-原子荧光光谱法测定。方法检出限为0.008 9(As)、0.008 1(Sb)、0.008 1(Bi)、0.001 7(Hg)μg/g,测定结果的相对标准偏差(RSD,n=12)为0.82%～7.6%,准确度△lgC=-0.01～0.02。方法简便、成本低,检测结果准确,检出限、准确度及精密度均能达到行业规范要求,适用于1∶5万区域地质调查样品水系沉积物、土壤中As、Sb、Bi、Hg等4种元素的测定。     

连续流动原子荧光光谱法同时测定化探样品中的汞和铋北大核心CSCD

As、Sb、Bi、Hg是化探样品的常测元素。这4种元素都能在盐酸-硝酸（3＋1）混合液中溶出,并可使用原子荧光仪器进行测定^（[1-7]）。20世纪90年代以前都是使用单道原子荧光光谱仪逐一测定各元素。后来随着双道原子荧光光谱仪的普及,一般使用溶矿后原液同时测定Hg和Bi元素,预还原后溶液同时测定As和Sb元素。     

连续流动原子荧光光谱法同时测定化探样品中的汞和铋

正As、Sb、Bi、Hg是化探样品的常测元素。这4种元素都能在盐酸-硝酸(3+1)混合液中溶出,并可使用原子荧光仪器进行测定~([1-7])。20世纪90年代以前都是使用单道原子荧光光谱仪逐一测定各元素。后来随着双道原子荧光光谱仪的普及,一般使用溶矿后原液同时测定Hg和Bi元素,预还原后溶液同时测定As和Sb元素。连续流动是相对于断续流动而言,即测定完上一个样品后,不设定清洗步骤,直接吸入下一样品,     

化学蒸气发生-四通道原子荧光光谱法同时测定水样中的痕量砷、锑、硒和汞

应用自行设计的化学蒸气发生-四通道无色散原子荧光光谱仪,建立了同时测定水样中As、Sb、Se、Hg的新方法.在实验中优化了四元素同时化学蒸气发生条件和测定的最佳工作参数.在样品预处理阶段用HCl将Se6+还原为Se4+,然后用质量浓度5 g/L硫脲将As5+和Sb5+还原为As3+和Sb3+.在最佳条件下,方法对As、Sb、Se、Hg的检出限分别为0.05、0.03、0.05、0.01 ng/mL(3d);RSD分别为0.42%、0.74%、0.97%、1.0%(对5 ng/mL As、Sb、Se和0.5ng/mL Hg混合标准,n=7).用所建立的方法对不同类型水样中的As、Sb、Se、Hg进行了同时测定,测定结果与用标准方法测定所得结果之间无明显差异,各元素的加标回收率在93%～105%.     

化学蒸气发生-四通道原子荧光光谱法同时测定高纯金中的痕量As,Sb,Bi,Te

采用化学蒸气发生-四通道原子荧光光谱法测定了高纯金中的痕量砷、锑、铋和碲。用乙酸乙脂萃取分离金,水相还原后采用化学蒸气发生-四通道原子荧光光谱法测定高纯金中的痕量砷、锑、铋和碲。在最佳条件下,方法对As,Sb,Bi,Te的检出限分别为0.04,0.05,0.04,0.03 ng/mL(3σ);测定精密度分别为0.98,0.89,0.94,0.99%(对10 ng/mL As,Sb,Bi和Te混合标准,n=7)。方法对实际样品中的As,Sb,Bi,Te进行了同时测定,测定结果与标准方法无明显差异,各元素的加标回收率为95%～105%。     

原子荧光法测定烟中砷与汞

众所周知,砷与汞都是有毒元素,尤其它的气体毒性更大。为了使人们充分认识到吸烟的危害性,我们用原子荧光光度计测定了烟中的砷和汞。 1.仪器与试剂 XDY-1双道原子荧光光度计。DW-1微波发生器。氢化物发生器。砷和汞无极放电灯。 1mg/ml Hg标准储备液。1mg/ml As标准储备液。硫脲和抗坏血酸各含5％混合溶液作为预还原剂。     

硼氢化钾还原-无色散原子荧光测定化探样及水样中痕量汞

原子荧光光谱法目前已发展成为一种新的痕量分析技术。特别是氢化物法配合无色散原子荧光仪器,在分析As、Sb、Bi、Se、Te及Hg等其他化学手段感到困难的痕量元素时效果更好。本文对报导较少的硼氢化钾还原-无色散原子荧光测汞方法作了比较全面的介绍。经过近万个化探样品的分析,证明方法灵敏、快速、可靠,具有一定特点。     

HG-ICP-MS同时测定生物样品中痕量As,Se,Hg

以HNO3为介质,采用自行研制的二级气液分离器代替易消耗的膜分离器,在优化的实验条件下,采用HG-ICP-MS实现了As,Se,Hg的同时测定,分别获得了0.022,0.016,0.009 ngmL的检出限。实验研究了二级气液分离器中的气液分离行为、样品酸度、NaBH4质量浓度和引入方式等因素对测定灵敏度和精密度的影响。实验的结果表明,HG-ICP-MS同时测定As,Se,Hg的主要干扰来自于Fe,cu等过渡金属离子,样品溶液中抗坏血酸-硫脲的加入可以掩蔽这些离子的干扰。利用所建立的方法测定了人发、灌木叶和大米粉标样中痕量的As,Se,Hg,结果与标准参考值相符。     

化学蒸汽发生/电感耦合等离子体质谱法测定近岸及河口海水中的超痕量砷、锑、铋、锗、锡、汞

建立了化学蒸汽发生(CVG)电感耦合等离子体质谱(ICP MS)同时测定近岸及河口海水中超痕量As、Sb、Bi、Ge、Sn和Hg元素的方法.研究了CVG过程中KBH4、盐酸和硫脲的浓度以及样品流速、载气流速、海水样品盐度等对方法分析性能的影响.结果表明,在0.70％6盐酸、0.10 g/L硫脲、11.0 g/L硼氧化钾...     

Slurry sampling flow injection chemical vapor generation inductively coupled plasma mass spectrometry for the determination of trace Ge,As, Cd,Sb, Hg and Bi in cosmetic lotions

A slurry sampling inductively coupled plasma mass spectrometry (ICP-MS) method has been developed for the determination of Ge, As, Cd, Sb, Hg and Bi in cosmetic lotions using flow injection (FI) vapor generation (VG) as the sample introduction system. A slurry containing 2% m/v lotion, 2% m/v thiourea, 0.05% m/v l-cysteine, 0.5 μg mL⁻¹ Co(II), 0.1% m/v Triton X-100 and 1.2% v/v HCl was injected into a VG-ICP-MS system for the determination of Ge, As, Cd, Sb, Hg and Bi without dissolution and mineralization. Because the sensitivities of the analytes in the slurry and that of aqueous solution were quite different, an isotope dilution method and a standard addition method were used for the determination. This method has been validated by the determination of Ge, As, Cd, Sb, Hg and Bi in GBW09305 Cosmetic (Cream) reference material. The method was also applied for the determination of Ge, As, Cd, Sb, Hg and Bi in three cosmetic lotion samples obtained locally. The analysis results of the reference material agreed with the certified value and/or ETV-ICP-MS results. The detection limit estimated from the standard addition curve was 0.025, 0.1, 0.2, 0.1, 0.15, and 0.03 ng  g⁻¹ for Ge, As, Cd, Sb, Hg and Bi, respectively, in original cosmetic lotion sample.     

Determination of As, Sb, Bi and Hg in water samples by flow-injection inductively coupled plasma mass spectrometry with an in-situ nebulizer/hydride generator

A simple and very inexpensive in-situ nebulizer/hydride generator was used with inductively coupled plasma mass spectrometry (ICP-MS) for the determination of As, Sb, Bi and Hg in water samples. The application of hydride generation ICP-MS alleviated the sensitivity problem of As, Sb, Bi and Hg determinations encountered when the conventional pneumatic nebulizer was used for sample introduction. The sample was introduced by flow injection to minimize the deposition of solids on the sampling orifice. The elements in the sample were reduced to the lower oxidation states with L-cysteine before being injected into the hydride generation system. This method has a detection limit of 0.003, 0.003, 0.017 and 0.17 ng ml⁻¹ for As, Bi, Sb and Hg, respectively. This method was applied to determine As, Sb, Bi and Hg in a CASS-3 nearshore seawater reference sample, a SLRS-2 riverine water reference sample and a tap water collected from National Sun Yat-Sen University. The concentrations of the elements were determined by standard addition method. The precision was better than 20% for most of the determinations.     

Simultaneous determination of arsenic, antimony, bismuth and mercury in geological materials by vapor generation-four-channel non-dispersive atomic fluorescence spectrometry

Chemical vapor generation (CVG) coupled with non-dispersive atomic fluorescence spectrometry (NDAFS) has been widely used for determination of vapor-forming elements, but most of such works have been focused on single element analysis, and reports dealing with more than three elements simultaneous determination by CVG-NDAFS are rare. In this work, a sensitive and robust analytical procedure for the simultaneous determination of arsenic, antimony, bismuth and mercury in geological materials using vapor generation-four-channel non-dispersive atomic fluorescence spectrometry has been developed. The conditions of instrumentation and vapor generation of arsenic, antimony, bismuth and mercury were optimized. The optimized concentrations of KBH(4) and HCl required for analytes generation were 1.3% (m/v) and 20% (v/v), respectively. The interferences of coexisting ions and mutual hydride interferences were investigated carefully. One thousand milligrams per litre of Fe(3+); 500mgl(-1) of Pb(2+), Zn(2+), Mn(2+); 50mgl(-1) Cu(2+), Ni(2+), Cr(6+), Co(2+); 10mgl(-1) Ag(+) and 5mgl(-1) Au(3+) does not interfere with the determination of As, Sb, Bi and Hg. Associating a dilution of 1:250 (m/v) in the procedure of sample pretreatment, the tolerant concentrations of As, Sb, Bi and Hg in real geological materials are 2500, 1000, 250 and 5000ppm, respectively. Under optimal conditions, the detection limits for As, Sb, Bi and Hg were determined to be 0.068, 0.047, 0.037 and 0.008ngml(-1), respectively. The precisions for seven replicate determinations at the 5ngml(-1) of As, Sb, Bi and 1ngml(-1) of Hg were 0.47, 0.60, 0.97 and 0.93% (R.S.D.), respectively. Sample digestion was carried out on 500mg sample with 3ml HNO(3) and 10ml HCl, followed by addition of thiourea solution for the quantitative reduction of As(V), Sb(V) to As(III), Sb(III). The proposed method was successfully applied to the simultaneous determination of As, Sb, Bi and Hg in a series of certified geological reference materials using simple aqueous standard calibration technique. The results obtained are in good agreement with the certified values.     

赶酸对微波消解-氢化物发生-原子荧光法测定谷物中砷元素的影响

在利用氢化物发生-原子荧光分测定谷物类样品中砷元素时,硫脲-抗坏血酸的还原效果会受到硝酸含量的影响,试液中硝酸含量过高,会与硫脲-抗坏血酸溶液发生氧化还原反应,降低其还原效率。本研究通过对赶酸时间和赶酸温度进行试验,获得最佳的赶酸条件,结合微波消解技术,利用氢化物发生-原子荧光光谱法测定谷物中的微量砷,结果表明,谷物中砷浓度与荧光强度呈线性关系,线性方程为 y=0.0028x-0.1728,线性相关系数R2=0.9993,检出限为1.72ng/g。 通过对9份样品进行检测,其相对标准偏差RSD在4.32-7.59%之间,其准确度相对误差RE均小于±6.50%。经多次检测证实该方法较稳定,可用于谷物类样品中砷元素的快速测定。     

Optimization of a single-drop microextraction method for multielemental determination by electrothermal vaporization inductively coupled plasma mass spectrometry following in situ vapor generation

A headspace single-drop microextraction (HS-SDME) method has been developed in combination with electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) for the simultaneous determination of As, Sb, Bi, Pb, Sn and Hg in aqueous solutions. Vapor generation is carried out in a 40 mL volume closed-vial containing a solution with the target analytes in hydrochloric acid and potassium ferricyanide medium. Hydrides (As, Sb, Bi, Pb, Sn) and Hg vapor are trapped onto an aqueous single drop (3 µL volume) containing Pd(II), followed by the subsequent injection in the ETV. Experimental variables such as medium composition, sodium tetrahydroborate (III) volume and concentration, stirring rate, extraction time, sample volume, ascorbic acid concentration and palladium amount in the drop were fully optimized. The limits of detection (LOD) (3σ criterion) of the proposed method for As, Sb, Bi, Pb, Sn and Hg were 0.2, 0.04, 0.01, 0.07, 0.09 and 0.8 µg/L, respectively. Enrichment factors of 9, 85, 138, 130, 37 and 72 for As, Sb, Bi, Pb, Sn and Hg, respectively, were achieved in 210 s. The relative standard deviations (N = 5) ranged from 4 to 8%. The proposed HS-SDME-ETV-ICP-MS method has been applied for the determination of As, Sb, Bi, Pb, Sn and Hg in NWRI TM-28.3 certified reference material.     

Determination of mercury, selenium, bismuth, arsenic and antimony in human hair by microwave digestion atomic fluorescence spectrometry

A novel method for determination of Hg, Se, Bi, As and Sb based on microwave digestion followed by continuous flow vapour generation atomic fluorescence spectrometry was developed. The digestion for Hg was based on a two stage digestion involving HNO(3) and H(2)O(2), whilst for the hydride forming elements a common digestion using HCl and H(2)O(2) was found to be the most effective. The instrumentation and chemistry were optimised in order to provide the best accuracy and precision. The method detection limit for hair samples was found to be 0.2 ng g(-1) for Hg and between 2 and 10 ng g(-1) for the hydride forming elements. The atomic fluorescence detector showed excellent linearity over the concentration ranges studied with linear correlation co-efficients between 0.99984 and 0.99997. To validate the accuracy of the method a human hair certified reference material (GBW 0706) was analysed and excellent agreement with the certified value was obtained for all elements.     

Simultaneous determination of trace arsenic, antimony, bismuth and selenium in biological samples by hydride generation-four-channel atomic fluorescence spectrometry

A new and sample technique for the simultaneous determination of trace arsenic, antimony, bismuth and selenium in biologic samples by hydride generation-four-channel nondispersive atomic fluorescence spectrometry was development. The conditions of instrumentation and hydride generation of arsenic, antimony, bismuth and selenium were optimized. For reducing hexavalent Se to the tetravalent state was to heat the sample with 6 mol l⁻¹ HCl, and then pre-reducing pentavalent As and Sb to the trivalent state was achieved by the addition of 0.05 mol l⁻¹ thiourea. The interferences of coexisting ions were evaluated. Under optimal conditions, the detection limits for As, Sb, Bi and Se were determined to be 0.03, 0.04, 0.04 and 0.03 ng ml⁻¹, respectively. The precision for seven replicate determinations at the 5 ng ml⁻¹ of As, Sb, Bi and Se were 0.9, 1.2, 1.3 and 1.5% (R.S.D.), respectively. The proposed method was successfully applied to the simultaneous determination of As, Sb, Bi and Se in a series of Chinese certified biological reference materials using simple aqueous standard calibration technique, the results obtained are in good agreement with the certified values.     

Simultaneous spectrophotometric determination of Bi(III) and Sb(III) based on their complexes with iodide in acidic media using the H-point standard addition method and first-derivative spectrophotometry.

The H-point standard addition method (HPSAM) was applied to the simultaneous determination of Bi(III) and Sb(III). This method is based on the difference in the absorbance of complexes of Bi(III) and Sb(III) with iodide in acidic media in different wavelength pairs. The results showed that Bi(III) and Sb(III) can be determined simultaneously with concentration ratios of 15:1 to 1:20. First-derivative spectrophotometry was also used for the simultaneous determination of Bi(III) and Sb(III) based on their complexes with iodide. The proposed methods were successfully applied to the simultaneous determination of Bi(III) and Sb(III) in synthetic samples.