碲化铋红外透明导电薄膜的制备与光电性能（特邀）

采用射频磁控溅射法在石英衬底和硒化锌衬底上制备了碲化铋薄膜,分别研究了薄膜厚度、退火温度对薄膜微观结构和光电性能的影响。利用X射线衍射仪、X射线光电子能谱仪和冷场发射扫描电子显微镜,分析了薄膜结构、成分和形貌。结果表明,退火有利于薄膜的结晶,且不改变晶体的择优取向。傅里叶变换红外光谱测试结果表明,在石英衬底和硒化锌衬底上沉积的薄膜,光学透过率随着薄膜厚度和退火温度的增加而减小,在硒化锌衬底上沉积的薄膜透过波段比石英长,且光学透过率更加稳定。霍尔效应测试结果表明,随着薄膜厚度和退火温度的增加,薄膜的电阻率逐渐减小,最小为1.448×10^-3Ω·cm,迁移率为27.400 cm²·V^-1·s^-1,载流子浓度为1.573×10²⁰ cm^-3。在石英衬底上沉积的15 nm厚的Bi₂Te₃薄膜,在1～5μm波段的透过率达到80%,退火200℃后透过率达到60%,电阻率为5.663×10^-3Ω·cm。在...     

用激光分子束外延在Si衬底上外延生长高质量的TiN薄膜

采用激光分子束外延技术,利用两步法,在Si单晶衬底上成功地外延生长出TiN薄膜材料.原子力显微镜分析结果显示, TiN薄膜材料表面光滑,在10 μm×10 μm范围内,均方根粗糙度为0842nm.霍耳效应测量结果显示,TiN薄膜在室温条件下的电阻率为36×10^-5Ω·cm,迁移率达到5830 cm²/V·S,表明TiN薄膜材料是一种优良的电极材料.X射线θ—2θ扫描结果和很高的迁移率均表明,高质量的TiN薄膜材料被外延在Si衬底 关键词： 激光分子束外延 TiN单晶薄膜 外延生长     

α-四噻吩薄膜的生长及性能研究

利用原子力显微镜(AFM)、X射线衍射仪(XRD)研究了在氧化硅衬底上生长的α-四噻吩(α-4T)薄膜的表面形貌及分子取向。在低温下,获得了大尺寸、高有序的α-4T薄膜,为横向生长模式。衬底温度35 ℃以上转为纵向生长模式。晶体结构分析发现,α-4T薄膜属于单斜晶系,分子c-轴垂直基板排列。强的衍射峰和高有序的衍射峰意味着α-4T薄膜具有高的有序性和结晶性。电性能研究发现,提高衬底温度有利于提高薄膜的迁移率,衬底温度为35 ℃时器件迁移率为3.53×10^-2 cm²·V^-1·s^-1。但衬底温度进一步增加,迁移率反而下降,与原子力分析结果一致。低温退火可以降低器件的亚阈值陡度,从13.27 V·dec^-1降低到3.83 V·dec^-1,使器件的界面缺陷降低,电性能提高。     

衬底温度对MOCVD法沉积ZnO透明导电薄膜的影响

研究了衬底温度对MOCVD技术制备的ZnO薄膜的微观结构和光电特性影响. XRD和SEM的研究结果表明，衬底温度对ZnO薄膜的微观结构有显著影响，明显的形貌转变温度大约发生在175℃，低于175℃，薄膜呈镜面结构，晶粒为球状，高于177℃的较高温度范围，薄膜从“类金字塔”状的绒面结构演化为“岩石”状显微组织；随着温度增加，薄膜的晶粒尺寸明显增大.绒面结构的未掺杂ZnO薄膜具有17.96 cm²/V·s的高迁移率和3.28×10^-2 Ω·cm的低电阻率，对ZnO薄膜的进一步掺杂和结构优化有望应用于Si薄膜太阳电池的前电极. 关键词： MOCVD ZnO薄膜 透明导电氧化物 太阳电池     

基于聚(4-乙烯基苯酚)衬底修饰层喷墨打印的小分子有机半导体薄膜制备和表征

采用旋涂法预先在SiO₂衬底表面形成一层聚（4-乙烯基苯酚）（PVP）作为表面修饰层,以喷墨打印的6,13-双（三异丙基甲硅烷基乙炔基）并五苯（TIPS并五苯）作为有源层制作有机薄膜晶体管,有效改善了有机半导体薄膜的形貌。采用真空热蒸镀工艺制备源漏电极,形成底栅顶接触结构的有机薄膜晶体管（OTFT）器件。作为对比,在未经过表面修饰的SiO₂衬底上采用相同条件打印TIPS并五苯薄膜晶体管,发现在经过PVP修饰的SiO₂衬底上打印的单点厚度更均匀,咖啡环效应被抑制或被消除;而通过多点交叠打印形成的矩形薄膜的晶粒尺寸更大,相应的OTFT器件具有更高的场效应迁移率。在有PVP修饰层的衬底上制作的OTFT,器件在饱和区的平均场效应迁移率达到了0.065 cm²·V^-1·s^-1;而直接在SiO₂衬底上制作的器件,相应的平均场效应迁移率仅为0.02 cm²·V^-1·s^-1。     

衬底温度对磁控溅射制备掺铝氧化锌薄膜的结构和光电性能的影响

利用射频磁控溅射在石英基片上沉积掺铝氧化锌薄膜,研究了衬底温度对薄膜结构和光电性能的影响.当给衬底加热时,X射线衍射观测(002)峰相对强度明显增强.在衬底温度250℃下制备的薄膜的晶粒尺寸最大,为24.9nm,表面粗糙度最小,为8.1nm,表明在衬底温度250℃下制备的薄膜的结晶效果最好.衬底温度从30℃升高到250℃,薄膜的电阻率相应地从14.35×10-4Ω·cm降低到7.18×10-4Ω·cm,随着衬底温度的升高,电阻率反而增大.所有样品在可见光区的平均光学透射率都大于85%.引入品质因子分析薄膜的光电性能,当衬底温度为250℃时,品质因子最大为16.15×10-3Ω-1,其光电性能最好.     

有机衬底SnO2:Sb透明导电膜的制备与特性研究

常温下,采用射频磁控溅射法在有机的柔性衬底上制备出了SnO2:Sb透明导电膜,并对薄膜的结构和光电性质进行了研究.制备的样品为多晶薄膜,并且保持了二氧化锡的金红石结构.性能良好的薄膜电阻率为6.5×10-3Ω·cm,载流子浓度为1.2×1020cm-3,霍耳迁移率是9.7cm2·V-1·s-1.薄膜在可见光区的平均透过率达到了85%. 关键词： 柔性衬底 SnO2:Sb透明导电膜 射频磁控溅射法     

溶胶-凝胶法制备Li-N双掺p型ZnO薄膜的结构、光学和电学性能

采用溶胶-凝胶法在n型Si(100)衬底上沉积Li-N双掺杂ZnO薄膜,经X射线衍射和扫描电镜图片分析,所制备薄膜具有多晶纤锌矿结构和高的c轴择优取向.室温下霍尔效应测试结果显示Li-N双掺杂ZnO薄膜具有p型导电特性.在Li掺杂量为15.0at%,Li/N（摩尔比）为1∶1,700℃退火等优化条件下得到的最佳电学性能结果是：电阻率为0.34 Ω·cm,霍尔迁移率为16.43 cm²/V·s,载流子浓度为2.79×10¹⁹ cm^{-3关键词： Li-N双掺 p型ZnO薄膜 溶胶-凝胶 性能}     

热丝化学气相沉积技术低温制备多晶硅薄膜的结构与光电特性

以金属W和Ta为热丝，采用热丝化学气相沉积 ，在250℃玻璃衬底上沉积多晶硅薄膜.研究了热丝温度、沉积气压、热丝与衬底间距等沉积参数对硅薄膜结构和光电特性的影响，在优化条件下获得晶态比X_c＞90%，暗电导率σ_d=10^-7—10-6Ω ^-1cm^-1，激活能E_a=0.5eV，光能隙E_opt≤1.3 eV的多晶硅薄膜. 关键词： 多晶硅薄膜 热丝化学气相沉积 光电特性     

射频反应性溅射沉积的Cd2SnO4薄膜物理性质与缺陷特性研究

在Ar+O₂混合气氛中射频反应性溅射Cd-Sn合金靶制备了透明导电Cd₂SnO₄(简称CTO)薄膜。用X射线衍射测量了CTO膜的结构。实验结果表明,这种薄膜的电学和光学性质依赖于混合气体中的氧浓度、衬底温度以及沉积后的热处理。获得的CTO膜最低电阻率为1.74×10^-6Ω·cm,可见光光谱区最高透射率为95％。对于氧浓度为6％、衬底温度为400℃时沉积的CTO膜,经热处理后,其光隙能由热处理前的2.37eV增大为2.6 关键词：     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.