锐钛矿型TiO2水溶胶的低温制备及其表征

Anatase titanium dioxide hydrosol was prepared at low temperature by a simple method. The title material was characterized by TEM, XRD, FTIR and BET, respectively. The photocatalytic activity of the as-prepared TiO₂ was evaluated by the degradation of methyl orange solution under sunlight and the photocatalytic oxidation of acetone in air. The results showed that the titanium dioxide hydrosol was composed of anatase phase with average grain size of about 7 nm, and the crystallinity became more perfect with the increase of temperature. The BET surface areas were more than 220 m²·g^-1 for these samples. It is found that the photocatalytic activity was much better for the higher heat processing temperature. Especially, the photocatalytic activity of the sample with a heat treatment of 110 ℃ was better than that of P25. In addition, TiO₂ hydrosol also possessed good photocatalytic activity under the sunlight illumination.     

CexPr1-xO2-δ复合氧化物的XRD和Raman表征

A series of Ce_xPr_1-xO_2-δ mixed oxides were synthesized by sol-gel method and characterized by Raman and XRD techniques. When x value was changed from 1.0 to 0.5, only a cubic phase CeO₂ was observed. The samples were very well crystallized on decreasing x from 0.50 to 0.99. For Ce_xPr_1-xO_2-δ samples 465 cm^-1 and 1 150 cm^-1 Raman peaks are attributed to the Raman active F_2g mode of CeO₂. The broad peak at about 570 cm^-1 in the region of 0.3 ≤x≤ 0.99 can be linked to lattice defects resulting in oxygen vacancies. The new band at about 195 cm^-1 may be attributed to the asymmetric vibration caused by the formation of oxygen vacancies. Calcination temperatures had great effect on the peak intensity for CeO₂ but less effect on Ce_0.8Pr_0.2O_2-δ in Raman spectra. It might be due to the transformation of the colors for the mixed oxides, the insertion of Pr atom into the ceria lattice could enhance the sintering resistance and thermal stability of the mixed oxides.     

合成大比表面γ-Mo2N的新方法

The production of high specific surface area γ-Mo₂N (up to 165 m²·g^-1, passivated) by temperature programmed reaction of MoO₃ with mixtures of N₂ and H₂ was reported. The synthetic condition of high surface area γ-Mo₂N (usually, S_BET>100 m²·g^-1) were quite difficult and the amount of starting material MoO₃ in each batch was much less than 0.5 gram. However, some synthetic conditions had been greatly improved in our experiments. The crystalline phase and specific surface area had been characterized by XRD and BET. The XRD gave some information for reaction mechanism.     

纳米Ce1-xLaxO2-δ的微波引诱燃烧合成及其性能表征

Nanometer Ce_1-xLa_xO_2-δ solid solutions were synthesized by microwave-induced combustion process us-ing cerium nitrate hexahydrate， lanthanum nitrate hexahydrate and urea as raw materials. The process took only six minutes to obtain La₂O₃-doped CeO₂ nanopowders. The nanopowders were characterized by XRD， Laser Raman spectrum ， UV-Vis spectroscopy，field-emission scanning electron micrograph(FE-SEM)and TEM. The results revealed that the grain size of Ce_1-xLa_xO_2-δ varied from 20 to 40 nm calculated by Scherer formula through the plane of (111)， that oxygen vacancy was produced in the crystal lattices and the concentration of oxygen vacancy was increased with La doping， therefore the covalence of Ce-O bond was strenthened， which results in more intensive UV-C(200～280 nm)absorption. It can be seen from SEM that the porous appearance was obtained. Grain size is no more than 40nm observed from TEM.     

硬脂酸法制备超细K2La2Ti3O10及其酸交换性质研究

A new stearic acid method(SAM) has been used to prepare ultrafine K₂La₂Ti₃O₁₀ nanocrystalline. Each state of synthesis process was followed by the use of FT-IR analysis. The resulting materials have been characterized by means of XRD， TEM， BET surface area analysis. The acid-exchanging property of the obtained product was also studied. The experimental results showed that comparing with the product of traditional solid-state reaction， the particle size of the K₂La₂Ti₃O₁₀ synthesized by SAM is greatly reduced， BET surface area is high(more than 11.83m²·g^-1) and has different acid-exchanging properties. It can be easily exfoliated in 2mol·L^-1 HNO₃ so-lution.     

一种锂离子二次电池正极材料LiVPO4Cl的水热法合成

Cathode material LiVPO₄Cl for lithium-ion rechargeable batteries was synthesized by one-step hydro-thermal method. The result of XRD measurement shows that LiVPO₄Cl material has a triclinic crystal structure， P1 space group; the results of SEM and TEM indicate that the sample is mostly single-crystalline， stick-like material; and the results of charge/discharge testing and cyclic voltammetry measurement demonstrate that the charging plateau of LiVPO₄Cl material maintains at 4.02 V and the discharging plateau at 3.86 V. After sufficient activation， the discharge capacity at 0.1C rate of the fortieth cycle of LiVPO₄Cl material with relatively higher content of carbon reaches 101 mAh·g^-1.     

CuO/Sn0.8Ti0.2O2催化剂的表征及对NO+CO反应活性研究

Reducibility and characteristics of CuO/Sn_0.8Ti_0.2O₂ catalysts were examined by using a microreactor-GC NO+CO reaction system, BET, TG-DTA, FTIR, XRD and H2-TPR techniques. CuO/Sn_0.8Ti_0.2O₂ had high activity in NO+CO reaction, showing 93% NO conversion at 300 ℃ in air, and 100% NO conversion at 225 ℃ after H₂ pretreatment. The pore size distribution of Sn_0.8Ti_0.2O₂ was mainly as micro-pores and meso-pores (1~5 nm), and the specific surface area and total pore volume of Sn_0.8Ti_0.2O₂ were 69 m²·g^-1 and 0.15 cm³·g^-1, respectively. As shown by XRD analysis, there was no CuO crystal diffraction peak at 9%CuO loading, but two CuO crystal diffraction peaks at 2θ 35.5° and 38.7° were present at 12% CuO loading. FTIR detected the adsorption of NO and CO on the surface of reduced 12%CuO/Sn_0.8Ti_0.2O₂. The Cu²⁺ sites and support surface adsorbed NO, and the process of NO adsorption led to the formation of N₂O and NO₃^-. In contrast, the Cu⁺、Cu⁰ sites and support surface adsorbed CO, and when the mixed gases of NO and CO were adsorbed by support surface, no NO₃^- was formed. H₂-TPR showed four reduction peaks (α, β, γ and δ). The α, β and γ peaks were the reductions of CuO species, and the δ peak was the reduction of Sn_0.8Ti_0.2O₂.     

储氧材料制备过程中的结构及织构变化

Ce_0.65Zr_0.35O₂ solid solution was prepared by co-precipitation method and characterized by X-ray diffraction (XRD), Raman spectra, BET, oxygen storage capacity (OSC) and temperature-programmed reduction measurements (H₂-TPR) after calcination at 100 ℃, 300 ℃, 600 ℃, and 1 000 ℃. The results showed that the precipitation was a crystalline of fluorite structure, and in the process of the precipitation transformation into Ce_0.65Zr_0.35O₂ solid solution, the fluorite structure of the precipitation kept unchanged. The samples had different BET surface areas and OSC at different temperatures, but they held the performance of stable structure. After 1 000 ℃, there didn′t appear the other crystalline phase. So the samples prepared by co-precipitation method had excellent texture and higher thermal stability.     

BaxCe0.8Y0.2O3-α固体电解质的氧离子导电性

Ba_xCe_0.8Y_0.2O_3-α(x=1.03，1，0.98) solid electrolyte samples show a single phase of orthorhombic perovskite of BaCeO₃. The oxide-ion conduction and transport number were detected in the temperature of 600～1000℃ by electrochemical oxygen permeation (oxygen pumping)， and compared with the results from the oxygen concentration cell. The relation between the ingredient of Ba and oxide-ion conduction was also researched. It was found that these electrolytes exhibited the mixed oxide-ionic and electronic hole conduction under the experimental temperature and oxygen gas. The oxide-ion transport numbers are 0.1～0.6， which are close to the results of the oxygen con-centration cell. They increase as the decrease of Ba content in the samples.     

N2O活化的Fe/ZSM-5表面活性氧的表征(英)

Temperature-programmed reduction (H₂-TPR) was employed to quantitatively characterize the active oxygen species generated from a high Fe-loading Fe/ZSM-5 catalyst exposed to N₂O at 250 ℃. [Fe-O-Fe]²⁺ dimer was determined as the active iron complex for N₂O decomposition to produce the active oxygen. Reduction of Fe³⁺ to Fe²⁺ by H₂ in the dimer and removal of OH^- groups from Fe²⁺ dimer by heating Fe/ZSM-5 to 700 ℃ were the prerequisites for the formation of this active Fe complex. A linear correlation with a slope of 1.0 between the amount of [Fe-O-Fe]²⁺ and that of active oxygen species was observed. Maximum amount of active oxygen species can be generated by reducing Fe/ZSM-5 catalyst with H₂ at the temperatures over 500 ℃ and then heating the resulting product in Ar to 700 ℃, followed by N₂O exposure at 250 ℃. The ratio of the total number of oxygen atoms (Ode) deposited by interaction of [Fe-O-Fe]²⁺ with N₂O to the amount of [Fe-O-Fe]²⁺ was 2. However, not all the deposited oxygen atoms were active oxygen (O_a); the ratio of O_a and O_de was 0.5. The iron dimer complex composing active oxygen is a five-atom ion [Fe₂O₃]²⁺; the most probable structure is as follows:     

负载型Pd三效催化剂：载体CeO2-ZrO2-BaO的制备及催化性能

制备了不同BaO含量的CeO2-ZrO2储氧材料,并以此材料为载体浸渍H2PdCl6制得三效催化剂.结果表明,不论新鲜还是1 000 ℃老化状态下,以10%BaO添加CeO2-ZrO2储氧材料制备的Pd三效催化剂活性最佳,起燃和完全转化温度最低.XPS结果证实,10%BaO添加.通过稳定PdO活性组分并改变其电子环境使得催化剂有最佳活性.而随着BaO含量持续增加,Pd活件组分相对处于较氧化状态.储氧量、低温N2吸附-脱附测试以及XRD测试结果均表明10%BaO添加的材料储氧量,比表面积以及孔容均最大,而且有适应三效催化的孔径.这些结果均有助于以其制备的Pd三效催化剂获得更好的活性以及热稳定性.     

陈化体系组成对Ce0.65Zr0.35O2储氧材料性能的影响

采用共沉淀法制备了Ce_0.65Zr_0.35O₂(CZ)储氧材料, 在传统的水陈化体系中引入了乙醇, 研究了乙醇的加入对CZ储氧材料性能的影响. 对所制备样品进行了傅里叶变换红外(FTIR)光谱、X射线光电子能谱(XPS)、粉末X射线衍射(XRD)、扫描电镜(SEM)、N₂吸附-脱附、储氧量(OSC)和H₂程序升温还原(H₂-TPR)的表征, 并考察了以CZ储氧材料为载体制备的单钯催化剂的三效性能. 结果表明, 乙醇引入陈化体系对样品的结构和性能有显著影响. 以醇水共存体系陈化制备的CZ储氧材料颗粒小、堆积松散、孔径分布宽、孔容大, 具有优异的储氧性能和热稳定性, 经1000 °C焙烧后, 比表面积为29.3 m²·g^-1, 储氧量仍高达520 μmol·g^-1. 以此为载体制备的单钯催化剂, 空燃比操作窗口宽, 对C₃H₈、CO、NO的转化明显优于水陈化体系制备的储氧材料所制备的催化剂.     

不同铈添加量对CeO2-ZrO2-Al2O3材料性能的影响

采用共沉淀法制备了一系列不同铈添加量的CeO2-ZrO2-Al2O3(CZA)储氧材料,并通过XRD、低温N2吸附-脱附、氧脉冲吸附(OSC)和H2-TPR等手段进行了表征。XRD结果表明,在1 000和1 100℃高温焙烧后,当CeO2添加量为8%时样品具有最好的结构稳定性能。N2吸附-脱附结果表明,CeO2添加量为8%时样品具有最好的织构性能,1 000℃时,比表面积和孔容分别为:136.6 m2.g-1和0.38 mL.g-1;1 100℃时,比表面积和孔容分别为:83.7 m2.g-1和0.23 mL.g-1。OSC结果显示,CeO2添加量为8%时样品具有最大的储氧量,1 000℃和1 100℃分别为70μmol.g-1和31μmol.g-1。H2-TPR结果表明,CeO2添加量为8%时样品具有最佳的还原性能。     

中温固体氧化物燃料电池复合阴极材料LaBiMn2O6-Sm0.2Ce0.8O1.9的制备与电化学性质

采用甘氨酸燃烧法合成了LaBiMn_2O_6粉体,并与Sm_(0.2)Ce_(0.8)O_(1.9)均匀混合制备了LaBiMn_2O_6-Sm_(0.2)Ce_(0.8)O_(1.9)(LBM-SDC)复合阴极材料。利用X射线衍射(XRD)和扫描电子显微镜(SEM)对材料的物相及微观形貌进行分析,结果表明LBM与SDC在1 000℃下有良好的化学稳定性。SDC的复合增加了氧离子传导路径,进而使氧还原反应(ORR)速度加快。电化学阻抗谱(EIS)测试结果表明,复合阴极极化电阻(Rp)随SDC复合量的增加呈现先降低后升高的趋势,当复合量为30%(w/w)时,阴极材料的性能最优。在700℃空气气氛下的极化电阻为0.186Ω·cm~2,相对LBM(0.717Ω·cm~2)减少74%。氧分压测试结果表明阴极反应的速率控制步骤为氧分子的吸附-解离过程。以复合阴极构筑的电解质支撑单电池Ni-SDC/SDC/LBM-30%SDC在700℃的最大输出功率密度为234 mW·cm~(-2),连续测试90 h输出功率衰减约4%。     

Polymorphism in mercury(I) selenite(IV): preparation, crystal structures of α-, β-and γ-Hg2SeO3, and thermal behavior of the α- and β-modification

Mercury(I) selenite(IV) is polymorphic and crystallizes at least in three modifications, named α-, β-and γ-Hg₂SeO₃. Polycrystalline β-Hg₂SeO₃ was prepared by precipitation of a concentrated mercurous nitrate solution with selenous acid. Hydrothermal treatment of the colorless β-Hg₂SeO₃ powder in demineralized water at 250°C (10 days) yields light-yellow single crystals of α-Hg₂SeO₃ which show the highest density of the three modifications. Colorless needle-shaped single crystals of β-Hg₂SeO₃ and very few single crystals of γ-Hg₂SeO₃ co-crystallize from strongly diluted Hg₂(NO₃)₂ and H₂SeO₃ solutions and were grown by a diffusion technique. All crystal structures were solved and refined from single crystal diffractometer data sets and are based on Hg₂²⁺ dumbbells and trigonal pyramidal SeO₃²⁻ anions as the main building units. A common structural feature of all modifications is the formation of open channels extending parallel to the shortest crystallographic axis. The non-bonding orbitals of the Se^IV atoms are stereochemically active and protrude into the channels. Upon heating in an open system under N₂ atmosphere, both α- and β-Hg₂SeO₃ decompose in a well-separated three-step mechanism. The first step (T > 250°C) involves disproportionation into elementary mercury and α-HgSeO₃ which at ca. 400°C subsequently transforms into β-HgSeO₃. The second step between T = 400 and 500°C is accompanied by a loss of Hg and SeO₂ and the formation of the basic salt Hg₃SeO₆. In the third step, at temperatures between T = 500° and 600°C, this material decomposes completely. Upon heating in a closed system (sealed silica capillaries), β-Hg₂SeO₃ transforms between 320-340°C into the more dense α-Hg₂SeO₃ which on further heating likewise converts into elementary mercury and β-HgSeO₃.     

Synthesis of nano-sized crystalline oxide ion conducting fluorite-type Y2O3-doped CeO2 using perovskite-like BaCe0.9Y0.1O2.95 (BCY) and study of CO2 capture properties of BCY

Formation of nano-sized Y₂O₃-doped CeO₂ (YCO) was observed in the chemical reaction between proton conducting Y₂O₃-doped BaCeO₃ (BCY) and CO₂ in the temperature range 700-1000 °C, which is generally prepared by wet-chemical methods that include sol-gel, hydrothermal, polymerization, combustion, and precipitation reactions. BCY can capture CO₂ of 0.13 g per ceramic gram at 700 °C, which is comparable to that of the well-known Li₂ZrO₃ (0.15 g per ceramic gram at 600 °C). Powder X-ray diffraction (PXRD), energy dispersive X-ray analysis (EDX), laser particle size analysis (LPSA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and ac impedance spectroscopy were employed to characterize the reaction product obtained from reaction between BCY and CO₂ and subsequent acid washing. PXRD study reveals presence of fluorite-like CeO₂ (a=5.410 (1) Å) structure and BaCO₃ in reaction products. TEM investigation of the acid washed product showed the formation of nano-sized material with particle sizes of about 50 nm. The electrical conductivity of acid washed product (YCO) in air was found to be about an order higher than the undoped CeO₂ reported in the literature.     

Characterization and evaluation of Fe2O3/Al2O3 oxygen carrier prepared by sol–gel combustion synthesis

The sol-gel combustion synthesis (SGCS) for oxygen carrier (OC) to be used in chemical looping combustion (CLC) was first designed and experimented in this work, which is a new method of OC synthesis by combining sol-gel technique and solution combustion synthesis. Cheap hydrated metal nitrates and urea were adopted as precursors to prepare Fe₂O₃/Al₂O₃ OC at the molar ratio to unity (Fe1Al1), which was characterized through various means, including Fourier transforms infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffractor (XRD), and N₂ isothermal adsorption/desorption method. FTIR analysis on the chemical structure of the dried gel of Fe1Al1 indicated that urea was partly hydrolyzed and the hydrated basic carbonate was formed by the combination of groups such as (Fe(_1−yAl_y)_1−xO_1−3x, CO₃²⁻ and -OH-. By analyzing the staged products during SGCS, calcination was found as a necessary step to produce Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃. Through TGA-DTA, the decomposition of the dried gel was found to undergo five stages. The analysis of the evolved gases from the gel decomposition using FTIR partially confirmed the staged decomposition and assisted a better understanding of the mechanism of SGCS. XRD identification further substantiated the necessity of calcination to synthesize Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃, though it was not necessary for the synthesis of single phase α-Fe₂O₃ and α-Al₂O₃. Structural characterization performed on N₂ adsorption analyzer displayed that the pore shape of Fe1Al1 particles was heterogeneous. Finally, H₂ temperature-programmed reduction (TPR) of Fe1Al1 products in TGA indicated that the reduction reaction of Fe1Al1 OC after calcination was a single step reaction from α-Fe₂O₃ to Fe, and calcination benefited to improve the transfer rate of the lattice oxygen from the OC to fuel H₂. Furthermore, four times of reduction and oxidization (redox) reaction by alternating with H₂ and air demonstrated the synthesized OC had good reactivity and sintering-resistance, much suitable to be used in the realistic CLC. Overall, the SGCS method was found superior to other existent methods to prepare Fe₂O₃/Al₂O₃ OC for CLC application.     

g-C3N4/双钙钛矿复合材料的制备及氧催化性能

通过溶胶-凝胶法制备出不同Ni掺杂比例的双钙钛矿Sr_2Ni_xCo_(2-x)O_6(x=0.2,0.4,0.6,0.8),通过热分解法制备出具有层状结构的纳米颗粒g-C_3N_4,并制备其复合物催化剂。将双钙钛矿和g-C_3N_4分别制备成双功能电极片,用于测试其对氧还原(ORR)和氧析出(OER)的催化活性,然后选取具有最佳氧催化活性的Ni掺杂比例x=0.4的双钙钛矿与一定重量比例的g-C_3N_4进行复合,测试复合催化剂的氧催化活性。结果表明,复合后的催化剂催化效果明显优于单一催化剂,当g-C_3N_4添加量占双钙钛矿的30%(w/w)时复合催化剂催化氧还原反应的最大电流密度为395.7 mA·cm~(-2)(-0.6 V vs Hg/HgO),氧析出反应的最大电流密度为372.0mA·cm~(-2)(1 V vs Hg/HgO),这表明g-C_3N_4与Sr_2Ni_(0.4)Co_(1.6)O_6复合后协同催化能够提高双钙钛矿的氧催化活性。     

氧分子在Cu2O(111)表面吸附与解离的理论研究

本文采用密度泛函方法结合周期性平板模型,研究了氧原子和氧分子在完整和存在缺陷的Cu₂O(111)表面的吸附。计算结果表明氧原子倾向于吸附在配位饱和的Cu_CSA位,而对于氧分子,则强烈倾向于吸附在配位不饱和的Cu_CUS位。氧分子在含有氧空位的缺陷表面的优势吸附位为平行吸附于空位上方的桥位。过渡态的计算表明氧分子在缺陷表面的解离是一个活化能很小的放热过程。     

(ZrO2)0.92(Gd2O3)0.08纳米晶的水热合成及其烧结体的电性能

用新制备的(Gd，Zr)(OH)_x·yH₂O共沉淀作前驱体，在强碱性介质中用水热法合成了(ZrO₂)_0.92(Gd₂O₃)_0.08纳米立方晶，考察了反应温度、pH值等水热反应条件对纳米晶粒大小的影响。将(ZrO₂)_0.92(Gd₂O₃)_0.08