微量吸附量热研究CuO/γ-Al2O3催化剂的表面酸碱性质

The γ-Al₂O₃ supported CuO samples were studied. XRD results showed that the loading and calcination temperature affected the surface structure. For example， CuO crystallite appeared at the CuO loading of 7% (about 0.82mmol/100m²) on the support. Both CuO crystallite and CuAl₂O₄ spinel were present when the CuO/γ-Al₂O₃ sample was calcined at the same temperature (400℃). Microcalorimetric adsorption of CO₂ and NH₃ revealed that the strength of both the acidity and basicity decreased with the increase of CuO loading for the CuO/γ-Al₂O₃ sample. The increase of calcination temperature further decreased the basicity while the acidity was not affected.     

固溶体结构对Ca2-xSrxZn4Ti15O36∶Pr3+发光性质的影响

Ca_2-xSr_xZn₄Ti₁₅O₃₆∶Pr red long decay phosphor was synthesized by high temperature solid state reaction. Photoluminescence property and crystalline and unit cell parameters of the orthorhombic were investigated by fluorescence spectrophotometer and by powder X-ray diffraction, respectively. The emission intensity at 618 nm changes sharply when the concentration of Sr²⁺ (x) is less than 0.1 and the emission intensity reaches the maximum when x is equal to 0.007. There is an obviously broad excitation band at 270 nm when x is equal to 0.003 and it disappears gradually when x is over 0.01. The unit cell a parameter of Ca_2-xSr_xZn₄Ti₁₅O₃₆∶Pr decreases while c parameter increases with the increases of the concentration of the doped Sr²⁺. When x is over 0.1 the value of the unit cell parameters a and c become stable. TL peaks of Ca₂Zn₄Ti₁₅O₃₆∶Pr, Ca_1.993Sr_0.007Zn₄Ti₁₅O₃₆∶0.002Pr³⁺, 0.002Na⁺, are located at 62 ℃, 88 ℃, respectively, which indicates that there are deeper traps in Ca_1.993Sr_0.007Zn₄Ti₁₅O₃₆∶0.002Pr³⁺, 0.002Na⁺.     

CuO/TiO2/γ-Al2O3催化剂表征及对NO+CO反应性能研究

采用色谱-微反流动法反应装置考察了w%CuO/15%TiO₂/γ-Al₂O₃催化剂对NO+CO的反应活性;催化剂经空气氛或氢气氛预处理后,NO转化率达100%的反应温度分别是325和275 ℃;XRD仅能检测到γ-Al₂O₃晶相,负载15%CuO后可以检测到微弱的CuO晶相;H₂-TPR能检测到2个CuO的还原峰(α和β峰),将其归属于高度分散的CuO分别在裸露的γ-Al₂O₃和TiO₂/γ-Al₂O₃载体上的还原;原位红外分析结果表明催化剂经空气氛或氢气氛预处理后,吸附NO+CO反应气后,反应的中间产物N₂O出现的温度分别为200和150 ℃。     

阴极材料LaFe0.8-xCuxNi0.2O3的合成和烧结性能

LaFe_0.8-xCu_xNi_0.2O₃ (x=0.0~0.2) (LFCN), a new cathode material of solid oxide fuel cell (SOFC), was synthesized by Co-precipitation method using sodium bicarbonate. The lattice structures of samples with different x contents were characterized by XRD. Porosity and density of the porous LaFe_0.8-xCu_xNi_0.2O₃ (x=0.0~0.1) as a function of sintering temperature were investigated. It was found that the orthorhombic structure could be formed after calcination at 900 ℃ for 4 h. The particle size of LFCN was about 350 nm. The density of the porous LFCN increased with sintering temperature, but the opposite was true for the porosity. On the other hand, at the same sintering temperature, the porosity of LaFe_0.8-xCu_xNi_0.2O₃ (x=0.0~0.1) decreased with increasing x contents. It is indicated that the dopant of Cu on LaFe_0.8Ni_0.2O₃ can facilitate the sintering of the materials. After sintering at 1 100 ℃ for 4 h, the porous LaFe_0.7Cu_0.1Ni_0.2O₃ was still with appropriate structure, and its porosity was 29%.     

LiNi0.8Co0.2O2 / MWNTs复合物超级电容器电极材料的研究

Multiwalled carbon nanotubes (MWNTs) were used as the conductive additive in the electrode materials. The electrochemical properties of supercapacitors based on LiNi_0.8Co_0.2O₂ / MWNTs composite and LiNi_0.8Co_0.2O₂/acetylene black composite and MWNTs in 1.0 mol·L^-1 LiClO₄ / EC+DEC [V(EC)∶V(DEC)=1∶1] electrolyte were investigated by means of constant charge/discharge current tests, respectively. The experimental results show that the LiNi_0.8Co_0.2O₂ / MWNTs composite has better performance than that of others, and the maximum specific capacitance of the supercapacitor can reach 271.6 F·g^-1, while the energy density is up to 339.5 Wh·kg^-1. Furthermore, it is remarkable that the performance of MWNTs is better than that of acetylene black as the conductive additive.     

硬脂酸法制备超细K2La2Ti3O10及其酸交换性质研究

A new stearic acid method(SAM) has been used to prepare ultrafine K₂La₂Ti₃O₁₀ nanocrystalline. Each state of synthesis process was followed by the use of FT-IR analysis. The resulting materials have been characterized by means of XRD， TEM， BET surface area analysis. The acid-exchanging property of the obtained product was also studied. The experimental results showed that comparing with the product of traditional solid-state reaction， the particle size of the K₂La₂Ti₃O₁₀ synthesized by SAM is greatly reduced， BET surface area is high(more than 11.83m²·g^-1) and has different acid-exchanging properties. It can be easily exfoliated in 2mol·L^-1 HNO₃ so-lution.     

梯度材料LiNi0.8Co0.2O2的合成与表征

The gradient composite LiNi_0.8Co_0.2O₂ was synthesized using spherical Ni(OH)₂ particle coated by a sol-gel containing cobalt and lithium. The precursor was examined by DSC-TG. The gradient composite was characterized by SEM, EDS, XPS, XRD and ICP-AES. The XPS, EDS and ICP-AES results show that content of cobalt in the surface is higher than in the center of the spherical particle of the gradient composite. The first discharge specific capacity of the gradient composite sintered at 700 ℃ is 187.3 mAh·g^-1.     

Ceramic Filter Balls Loaded with α-Fe2O3 and Their Application to NH3-N Wastewater Treatment

Hydrolysis reaction of Fe(NO₃)₃ at a high temperature in the presence of urea as the homogeneous precipitant was studied. With the prepared ceramic filter balls loaded with α-Fe₂O₃ after high temperature calcination, the loading of α-Fe₂O₃ on the porous ceramic filter balls from Fe(NO₃)₃ solutions of different concentrations and mechanical stability of the loaded α-Fe₂O₃ were studied. The product was characterized using XRD and SEM. Adsorption experiments were conducted to evaluate the performance of the product in adsorbing NH₃-N. It turned out that the specific surface area of the ceramic filter balls loaded with α-Fe₂O₃ had increased to 36.5387 m²/g from original 4.6127 m²/g. When the concentration of Fe(NO₃)₃ was 0.40 mol/L, the loading of α-Fe₂O₃ on the ceramic filter balls accounted for 8.4% of the total mass of the adsorbent and α-Fe₂O₃ was adsorbed on the filter balls very well. The adsorption isotherm of NH₃-N on the ceramic filter ball adsorbent loaded with α-Fe₂O₃ was of Langmuir type. The saturated adsorption capacity was 3.33 mg/L, and the adsorption constant K was 0.1873. NH₃-N was adsorbed by α-Fe₂O₃ more easily, which was a kind of specific adsorption.     

预处理气氛对CuO/CeO2/γ-Al2O3催化剂表面性质及“NO+CO”反应性能的影响

用不同的预处理气氛制备了CeO₂/γ-Al₂O₃载体以调节表面Ce的价态,并以Cu(CH₃COO)₂为前驱体制备了CuCeAl催化剂。XRD和H₂-TPR的结果表明在还原气氛下处理的CeO₂/γ-Al₂O₃载体具有更多的活性氧原子,因此相应的CuCeAl催化剂表面有更多分散态的Cu²⁺/Cu⁺物种。NO+CO反应的结果表明分散态的Cu²⁺/Cu⁺是NO转化的活性物质,而Cu⁰在低温下具有较好的N₂选择性。因此,同时含有分散态Cu²⁺/Cu⁺和少量晶相Cu⁰的催化剂具有最好的催化性能。     

锂离子电池用Li4Ti5O12-碳复合材料的制备与电化学性能

Li₄Ti₅O₁₂-C composite was prepared by sol-gel method using ethyl alcohol as solvent, lithium acetate and tetrabutyl titanate as raw materials, and graphite as carbon source. Li₄Ti₅O₁₂-C composites were characterized by thermogravimertric(TG) analysis and differential thermal analysis(DTA), X-ray diffraction(XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and electrochemical tests. Results show that Li₄Ti₅O₁₂-C composite with 5% carbon containing can be obtained by annealing the precursor at 600 ℃ for 6 h in N₂ atomsphere. The composites can deliver a specific capacity of 167.1 mAh·g^-1, 99.0% and 105.1% of the capacity can be retained after discharged for 80 times at 0.1C and 2.0C, respectively. Compared with pure Li₄Ti₅O₁₂, Li₄Ti₅O₁₂-C composite shares larger discharge capacity, better cyclability and rate performance.     

CuO/Ti0.5Zr0.5O2催化剂对NO+CO反应的催化作用

环境治理是当今社会面临的一大主要问题。目前,城市空气污染日趋严重,特别是工厂和汽车排放的大量未燃烧的烃类、CO、NOx是主要的空气污染物。其中,氮氧化物(NOx)排放状况尤其严重,它的排放会给环境和人们生活带来严重危害,因此,如何有效地消除NOx已成为目前环境保护中一个非常     

Ca2+-Mg2+-Zn2+体系在水溶性聚磷酸铵溶液中螯合规律的研究

近年来,水溶性聚磷酸铵在液体肥料和复合肥料的领域受到了广泛的关注,并在发达国家中得到了大面积的推广及应用。在pH值为5.5~8.0、温度为278.15 K~323.15 K的条件下,本文采用滴定法研究Ca_²⁺-Mg_²⁺-Zn_²⁺体系在聚磷酸铵溶液中的螯合规律。实验结果表明：相同质量分数的聚磷酸铵溶液对金属离子的螯合量会随着体系中Ca_²⁺、Mg_²⁺、Zn_²⁺的摩尔浓度的变化而变化;随着温度的升高而逐渐降低;随着pH的增加而逐渐增加;随着聚合度的升高而逐渐增加。采用傅里叶红外光谱对聚磷酸铵和A₁B₃C₃体系的螯合物进行表征。     

La7O6(BO3)(PO4)2:Eu3+/Tb3+荧光材料的制备及其光致发光性能

采用优化的高温固相方法制备了稀土离子Eu³⁺和Tb³⁺掺杂的La₇O₆（BO₃）（PO₄）₂系荧光材料,并对其物相行为、晶体结构、光致发光性能和热稳定性进行了详细研究。结果表明,La₇O₆（BO₃）（PO₄）₂：Eu³⁺材料在紫外光激发下能够发射出红光,发射光谱中最强发射峰位于616 nm处,为⁵D₀→⁷F₂特征能级跃迁,Eu³⁺的最优掺杂浓度为0.08,对应的CIE坐标为（0.610 2,0.382 3）;La₇O₆（BO₃）（PO₄）₂：Tb³⁺材料在紫外光激发下能够发射出绿光,发射光谱中最强发射峰位于544 nm处,对应Tb³⁺的⁵D₄→⁷F₅能级跃迁,Tb³⁺离子的最优掺杂浓度为0.15,对应的CIE坐标为（0.317 7,0.535 2）。此外,对2种材料的变温光谱分析发现Eu³⁺和Tb³⁺掺杂的La₇O₆（BO₃）（PO₄）₂荧光材料均具有良好的热稳定性。     

Conversion of NO in NO/N2, NO/O2/N2, NO/C2H4/N2 and NO/C2H4/O2/N2 Systems by Dielectric Barrier Discharge Plasmas

An experimental study on the conversion of NO in the NO/N₂, NO/O₂/N₂, NO/C₂H₄/N₂ and NO/C₂H₄/O₂/N₂ systems has been carried out using dielectric barrier discharge (DBD) plasmas at atmospheric pressure. In the NO/N₂ system, NO decomposition to N₂ and O₂ is the dominating reaction; NO conversion to NO₂ is less significant. O₂ produced from NO decomposition was detected by an on-line mass spectrometer. With the increase of NO initial concentration, the concentration of O₂ produced decreases at 298 K, but slightly increases at 523 K. In the NO/O₂/N₂ system, NO is mainly oxidized to NO₂, but NO conversion becomes very low at 523 K and over 1.6% of O₂. In the NO/C₂H₄/N₂ system, NO is reduced to N₂ with about the same NO conversion as that in the NO/N₂ system but without NO₂ formation. In the NO/C₂H₄/O₂/N₂ system, the oxidation of NO to NO₂ is dramatically promoted. At 523 K, with the increase of the energy density, NO conversion increases rapidly first, and then almost stabilizes at 93–91% of NO conversion with 61–55% of NO₂ selectivity in the energy density range of 317–550 J L⁻¹. It finally decreases gradually at high energy density. A negligible amount of N₂O is formed in the above four systems. Of the four systems studied, NO conversion and NO₂ selectivity of the NO/C₂H₄/O₂/N₂ system are the highest, and NO/O₂/C₂H₄/N₂ system has the lowest electrical energy consumption per NO molecule converted.     

IR and Raman spectra of two layered aluminium phosphates Co(en)3Al3P4O16 · 3H2O and [NH4]3[Co(NH3)6]3[Al2(PO4)4]2 · 2H2O

The FT IR and FT Raman spectra of Co(en)₃Al₃P₄O₁₆ · 3H₂O (compound I) and [NH₄]₃[Co(NH₃)₆]₃[Al₂(PO₄)₄]₂ · 2H₂O (compound II) are recorded and analysed based on the vibrations of Co(en)₃³⁺, Co(NH₃)₆³⁺, NH₄⁺, Al---O---P, PO₃, PO₂ and H₂O. The observed splitting of bands indicate that the site symmetry and correlation field effects are appreciable in both the compounds. In compound I, the overtone of CH₂ deformation Fermi resonates with its symmetric stretching vibration. The NH₄ ion in compound II is not free to rotate in the crystalline lattice. Hydrogen bonding of different groups is also discussed.     

Ce3+,Tb3+,Eu3+共掺杂Sr2MgSi2O7体系的白色发光和能量传递机理

通过正交试验,采用高温固相法制备了Sr2-x-y-zMgSi2O7∶xCe3+,yTb3+,zEu3+系列样品.使用X射线衍射仪和荧光光谱仪表征了样品的物相和发光性质,并讨论了Ce3+-Tb3+-Eu3+共掺杂Sr2MgSi2O7体系中的能量传递过程.实验结果表明,在327 nm波长激发下,所合成荧光粉的发射峰主要位于387 nm(蓝紫)、542nm(绿)和611 nm(红)处;分别以387,542和611 nm为监控波长,所得激发光谱显示荧光粉在327 nm处有最好的激发.在327 nm光激发下,系列样品发光进入白光区.最优化的荧光粉为Sr1.91MgSi2O7∶0.01Ce3+,0.05Tb3+,0.03Eu3+,其色坐标为(0.337,0.313),是一种潜在的发光二极管(LED)用白色荧光粉.     

Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al₂O₃-SiO₂系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho³⁺/Yb³⁺共掺以ZnAl₂O₄为主晶相的ZnO-Al₂O₃-GeO₂-SiO₂系玻璃陶瓷。因[GeO₄]四面体和[SiO₄]四面体都是玻璃网络形成体,讨论了GeO₂取代SiO₂对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO₂的取代量为10.55%（w/w）时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色（546 nm）和弱的红色（650 nm）上转换发光,并研究了不同Ho³⁺/Yb³⁺掺杂比对样品上转换发光的影响,最终结果表明当Ho³⁺/Yb³⁺掺杂比为1：11（n/n）时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

Fe(0)(CO)3(Ph2Ppy)2Mn+Cln中金属-金属成键的光谱研究

本文研究了七个以反式二（二苯基膦吡啶）－三羰基铁为三齿配体的过渡金属双核配合物，将Ｊｏｒｇｅｎｓｅｎ建议的处理电荷转移光谱的方法推广处理ＭＭＣＴ跃迁，通过光学电负性的计算取得金属－金属成键的证据。由Ｒａｍａｎ光谱羰基伸缩振动频率的蓝移进一步支持这类化合物中存在金属－金属成键相互作用的推断。     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

稀土掺杂Lu3Al5O12荧光粉的发光特性及能量传递

采用高温固相法制备了Ce、Sm共掺Lu₃Al₅O₁₂荧光粉。通过X射线衍射分析、荧光光谱分析研究了样品的结构、发光特性,并通过理论计算研究了能量传递效率、能量传递的临界距离以及能量传递方式。X射线衍射分析表明所制备的荧光粉具有单一的石榴石结构;荧光光谱分析表明,在464 nm蓝光激发下,Sm³⁺的引入可增加Lu₃Al₅O₁₂：Ce,Sm发射光谱中红光成分,并且随着Sm³⁺浓度的增加,Ce³⁺发光强度逐渐减弱。计算出Ce³⁺、Sm³⁺之间的能量传递效率高达77.42%,确定了Ce³⁺、Sm³⁺之间的能量传递机制为偶极-偶极相互作用。