三维海胆状Co3O4的微纳结构制备及锂电池性能

水热法制备的合成海胆状Co₃O₄前驱物在空气中退火得到三维海胆状Co₃O₄的微纳结构. 采用FESEM、TEM、HRTEM以及XRD对产物进行形貌和结构的表征. 结果表明,合成的海胆状结构Co₃O₄由许多粒径约为15 nm的颗粒串接形成. 锂电池测试性能表明,制备的海胆状Co₃O₄首次放电容量达到1.369 Ah/g,经过20次循环     

焙烧温度对SiO2负载的Co3O4纳米粒子表面氧缺陷浓度和CO氧化催化性能的影响

以传统的浸渍法,在不同焙烧温度下制备了用于CO氧化反应的Co₃O₄/SiO₂催化剂．通过激光拉曼光谱(Raman)、X射线光电子能谱(XPS)、X射线衍射(XRD)、程序升温还原(TPR)和X射线吸收精细结构谱(XAFS)表征了该系列催化剂的结构．在所有的催化剂中,XRD和Raman光谱都只检测到了Co₃O₄晶相的存在．与Co₃O₄体相相比,XPS结果表明在200 oC焙烧的(Co₃O₄(200)/SiO₂)催化剂中Co₃O₄表面上存在着过量的Co²⁺．与XPS的结果一致,TPR结果表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄表面上存在氧缺陷, 并且XAFS结果也表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄具有更多的Co²⁺．提高焙烧温度使得过量的Co²⁺进一步氧化为Co³⁺,同时降低了表面氧缺陷浓度,从而得到计量比的Co₃O₄4/SiO₂催化剂．在所有的负载催化剂中Co₃O₄(200)/SiO₂催化剂表现出了最好的CO氧化催化性能,表明过量Co²⁺和表面氧缺陷的存在能够促进Co₃O₄催化CO氧化反应的活性.     

钴改性Fe3O4-MnO2催化转化生物质合成气制备液体燃料

本文制备了用于费托合成反应的钴改性Fe₃O₄-MnO₂双功能催化剂,并探究了钴负载量对Fe-Co协同效应的影响以及Fe₁Co_xMn₁催化剂的费托合成反应性能. 实验发现,在Fe₃O₄-Mn催化剂中加入Co可促进铁氧化物的还原、增加反应过程中铁位点的活性. 此外,Co的加入可增强Fe-Co金属间的电子转移,加强两者的协同作用,提高催化性能. Co负载较高的Fe₁Co_xMn₁催化剂可进一步促进加氢反应能力,使产品分布向短链烃方向转移. 在280 ^°C、2.0 MPa和3000 h^-1的最佳工况条件下,Fe₁Co₁Mn₁催化剂的液体燃料收率最高.     

压力对纳米CoFe2O4/SiO2复合材料结构的影响

 采用溶胶-凝胶工艺和高温高压实验技术,制备了纳米CoFe₂O₄/SiO₂复合材料。利用X射线衍射仪、扫描电子显微镜和振动样品磁强计,对样品的结构、微观形貌和磁性进行了研究,并对CoFe₂O₄中阳离子的占位情况进行了讨论。结果表明,随着处理压力的升高,样品的晶粒尺寸增大,晶格常数减小,比饱和磁化强度增大。通过计算结果可以推断,压力的升高导致CoFe₂O₄中的部分Fe³⁺从A位移向了B位,而部分Co²⁺则从B位移向了A位。     

纤维状TiO2/Bi2O3光催化剂的制备及其光催化性能

以C₁₆H₃₆O₄Ti和Bi(NO₃)·5H₂O为原料,以棉花纤维为生物模板,合成了系列纤维状TiO₂/Bi₂O₃光催化剂．采用XRD、SEM、UV-Vis等测试技术对样品的相结构、形貌和吸光性能等进行了表征分析．结果表明,样品中的Bi₂O₃为单斜相和四方相共存的混晶,纤维长度达到毫米级,     

脉冲激光沉积温度及氧压对Bi2Sr2Co2Oy热电薄膜晶体结构与电输运性能的影响

利用脉冲激光沉积技术在c-Al₂O₃单晶基片上制备了Bi₂Sr₂Co₂O_y热电薄膜并研究了沉积温度和氧压对薄膜晶体结构及电输运性能的影响.在最佳沉积条件下制备的单相、c轴取向的Bi₂Sr₂Co₂O_y薄膜的室温电阻率ρ和塞贝克系数S分别为2.9mΩ/cm和110μupV/K,其功率因子S²/ρ好于在单晶样品上得到的值.此外,该薄膜在低温下表现出较强的负磁阻效应,在2K,9T时达到了40%.     

LD抽运Er3+，Yb3+共掺磷酸盐玻璃被动调Q激光器的理论分析和数值计算

研究了以Co²⁺:MgAl₂O₄晶体为饱和吸收体的LD抽运Er³⁺,Yb³⁺共掺磷酸盐玻璃激光器.针对双掺离子之间的能量传递和Er³⁺的多种跃迁过程，结合Co²⁺:MgAl₂O₄晶体中Co²⁺离子的饱和吸收特性，给出了详尽的速率方程，在其基础上进行了数值分析，分析了输出镜透过率、激光介质长度、谐振腔长度、腔内往返损耗、饱和吸收体长度对激光阈值、峰值功率、单脉冲能量以及脉冲宽度的影响.     

具有介孔结构的MnSiO3@Fe3O4@C纳米粒子的制备以及作为pH响应的T1-T2*双模MRI造影剂的研究应用

本文通过一个简单的、温和的方案制备了平均尺寸为120 nm,介孔结构的纳米粒子MnSiO₃@Fe₃O₄@C. 粒子的细胞毒性微小,可以用作T₁-T₂^*双模MRI造影剂. 酸性条件下MnSiO₃@Fe₃O₄@C释放出大量的Mn²⁺缩短T₁弛豫时间,提高成像分辨率. 超顺磁性的Fe₃O₄可以增强T₂对比成像,检测病变组织. 类似于肿瘤微环境/细胞器的酸性PBS(pH=5.0)中Mn²⁺的释放率达到31.66%,约为中性条件(pH=7.4)下的7倍. 释放的Mn²⁺通过内吞作用被细胞摄取,经肾脏排出,细胞毒性实验表明,MnSiO₃@Fe₃O₄@C具有低的细胞毒性,即使高浓度的200 ppm MnSiO₃@Fe₃O₄@C对HeLa细胞的毒性也相对较小. 对荷瘤小鼠静脉注射定量MnSiO₃@Fe₃O₄@C后,可以观察到一个快速增强的对比成像,给药24 h后,T₁MRI信号显著增强,达到132%,而T₂信号则明显降低至53.8%,活体MR成像证明了MnSiO₃@Fe₃O₄@C可以同时作为阳性和阴性造影剂. 此外,得益于介孔MnSiO₃优秀的酸敏感性,MnSiO₃@Fe₃O₄@C可以作为一种潜在的药物载体,实现肿瘤的诊疗一体化.     

氧化还原可逆Nb2TiO7复合阴极电解池高温水蒸气电解研究

系统地研究Nb₂TiO₇与Nb_1.33Ti_0.67O₄材料相互转变的氧化还原循环可逆性能,同时研究Nb2TiO7和Nb_1.33Ti_0.67O₄样品随温度和氧分压变化的电导率,并与复合电极对称电池和电解池的电化学性能相关联. 在830 oC下,对Nb_1.33Ti_0.67O₄复合电极电解池进行水蒸气的电解研究测试. 电流电压曲线和电解池短期性能测试表明在低电压下主要为电极的还原和活化过程;而在高电压下主要为水蒸气的电解. 当3%H₂O/Ar/4%H_{2气体通入阴极时电解池水蒸气电解的法拉第效率为98.9%;而当通入气体转换为3%H2O/Ar时效率为89%.}     

Al掺杂的尖晶石型LiMn2O4的结构和电子性质

采用基于密度泛函理论的第一性原理方法, 在广义梯度近似(GGA)和GGA+U方法下对尖晶石型LiMn₂O₄及其Al掺杂 的尖晶石型LiAl_0.125Mn_1.875O₄晶体的结构和电子性质进行了计算. 结果表明: 采用GGA方法得到尖晶石型LiMn₂O₄是立方晶系结构, 其中的Mn离子为+3.5价, 无法解释它的Jahn-Teller 畸变. 给出的LiMn₂O₄能带结构特征也与实验结果不符. 而采用GGA+U方法得到在低温下的LiMn₂O₄和其掺杂 体系LiAl_0.125Mn_1.875O₄的晶体都是正交结构, 与实验一致. 也能明确地确定Mn的两种价态Mn³⁺/Mn⁴⁺的分布并且能够说明Mn³⁺O₆的z方向有明显的Jahn-Teller 畸变, 而Mn⁴⁺O₆则没有畸变. LiMn₂O₄的能带结构与实验比较也能够符合. 采用GGA+U方法对Al掺杂体系的LiAl_0.125Mn_1.875O₄的研究表明, 用Al替换一个Mn不会明显地改变晶体的电子性质, 但可以有效地消除Al³⁺O₆ 八面体的Jahn-Teller畸变, 从而改善正极材料LiMn₂O₄的性能, 这与电化学实验的观察结果相一致.     

Catalytic performance of Mn3O4 and Co3O4 nanocrystals prepared by sonochemical method in epoxidation of styrene and cyclooctene

A simple sonochemical method was developed to synthesis uniform sphere-like Co₃O₄ and Mn₃O₄ nanocrystals. Epoxidation of styrene and cyclooctene by anhydrous tert-butyl hydroperoxide over the prepared Co₃O₄ and Mn₃O₄ nanocatalysts was investigated. The results of conversion activity were compared with bulk Co₃O₄ and Mn₃O₄. Under optimized reaction conditions, the nanocatalysts showed a superior catalytic performance as compared to the bulk catalysts. Powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and BET surface area, were used to characterize and investigate the nanocatalysts.     

Highly sensitive room-temperature gas sensors based on hydrothermal synthesis of Cr2O3 hollow nanospheres

This paper reports that Cr₂O₃ hollow nanospheres（HNs） were synthesized via a hydrothermal approach and characterized by scanning electron microscopy,x-ray powder diffraction,transmission electron microscopy（TEM）,selective area electron diffraction and high resolution TEM,respectively.In addition,the room-temperature（RT） gas sensing properties of Cr2O3 HNs and conventional powders（CPs） were investigated by means of the surface photovoltage technique.The experimental data demonstrate that the RT gas sensor of the as-fabricated HNs reaches below 5 ppm whereas that of the CPs is about 40 ppm,which results from there being much more adsorbed and desorbed oxygen in HNs than in CPs at RT.The as-prepared Cr₂O₃ HNs could have potential applications as RT nanosensors.     

Synthesis of urchin-like Co3O4 hierarchical micro/nanostructures and their photocatalytic activity

Urchin-like Co₃O₄ hierarchical micro/nanostructures have been successfully synthesized by calcining urchin-like precursor CoCO₃, which are prepared by a facile hydrothermal route. The particle size of the urchin-like Co₃O₄ could be easily controlled by altering the calcination temperature. The morphology and structure of the as-prepared urchin-like products were characterized by XRD, FESEM and TEM. Photocatalytic measurement demonstrates that these urchin-like Co₃O₄ micro/nanostructures show good photocatalytic effect and their degradation efficiency is strongly dependent on their particle size. Furthermore, a plausible reaction mechanism is also proposed to illustrate the photocatalytic processes of Co₃O₄.     

双掺杂BaxAgyCa3-x-yCo4O9氧化物的织构与电输运性能

采用柠檬酸溶胶凝胶和放电等离子烧结制备了Ca位双掺杂型的Ba_xAg_yCa_3-x-yCo₄O₉烧结体,利用X射线衍射仪、扫描电子显微镜、电阻率测试仪等研究了烧结体相组成、取向度、织构及电性能.结果表明：含Ag的掺杂试样中出现了偏离化学计量比分布的Ag单质,掺杂试样取向度随Ba与Ag掺杂量之比x/y的增大而提高,含Ag的掺杂试样取向度低于未掺杂试样,不含Ag的掺杂试样取向度高于未掺杂试样.x=y=01的试样导电机理发生变化.Ba,Ag掺杂量相等的试样保持较低取向度的同时具有较低的电阻率,在973 K时达到最低值（73 mΩcm）,而取向度最低的Ag单掺杂试样电阻率在所有试样中最低,在973 K时为63 mΩcm. 关键词： 3Co₄O₉')" href="#">Ca₃Co₄O₉ 双掺杂 织构 电输运性能     

Facile method to prepare stable superhydrophobic Co3O4 surface

A facile and novel method was developed to fabricate rough Co₃O₄ surface with hierarchical micro- and nanostructures by the combination of simple solid state reactions and coating process. After modification with stearic acid, a superhydrophobic surface with water contact angle of 155 ± 1.8° and sliding angle of 2° was obtained. The superhydrophobic Co₃O₄ surface remained superhydrophobic property in a wide pH range from 3 to 14. The superhydrophobic Co₃O₄ surface also showed excellent self-cleaning property and high stability in ambient environments.     

硅纳米孔柱阵列及其四氧化三铁复合薄膜的湿敏电容特性研究

报道了硅纳米孔柱阵列（Si-NPA），Fe₃O₄复合的Si-NPA（Fe ₃O₄/Si-NPA）两种薄 膜材料的制备方法并对其形貌和结构进行了表征，研究了其电容湿度传感特性.结果表明，S i-NPA，Fe₃O₄/Si-NPA均为微米/纳米结构复合体系.当环境相对湿 度从11％上升到95％ 时，采用100 Hz的信号频率进行测试，以Si-NPA和Fe₃O₄/Si-NPA 为电介质材料制成的湿 敏元件的电容增加值分别为起始值的1500％和5500％；采用1000 Hz的信号频率测试时，则 分别为起始值的800％和12000％，显示出两种材料较高的湿度灵敏性和较强的绝对电容输出 信号强度.同时，在升湿和降湿过程中，Si-NPA，Fe₃O₄/Si-NPA都 具有较快的响应速度 ，其响应时间分别为15 s，5 s和20 s，15 s.文章结合材料的形貌和结构特性对其物理机理 进行了分析.上述结果表明，Si-NPA无论是直接作为湿度薄膜传感材料还是作为复合薄膜湿 度传感材料的衬底都具有很好的前景. 关键词： 硅纳米孔柱阵列 3O₄')" href="#">Fe₃O₄ 湿度电容传感特性     

调控氧空位实现高比表面积Co3O4纳米片上的产氧反应

Electrochemical water splitting requires efficient water oxidation catalysts to accelerate the sluggish kinetics of water oxidation reaction. Here, we designed an efficient Co₃O₄ electrocatalyst using a pyrolysis strategy for oxygen evolution reaction (OER). Morphological characterization confirmed the ultra-thin structure of nanosheet. Further, the existence of oxygen vacancies was obviously evidenced by the X-ray photoelectron spectroscopy and electron spin resonance spectroscopy. The increased surface area of Co₃O₄ ensures more exposed sites, whereas generated oxygen vacancies on Co₃O₄ surface create more active defects. The two scenarios were beneficial for accelerating the OER across the interface between the anode and electrolyte. As expected, the optimized Co₃O₄ nanosheets can catalyze the OER efficiently with a low overpotential of 310 mV at current density of 10 mA/cm² and remarkable long-term stability in 1.0 mol/L KOH.     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.