聚溴酚蓝修饰玻碳电极的制备及电化学性质

在含溴酚蓝的磷酸缓冲溶液中,应用循环伏安法于经预处理的玻碳电极上形成聚合物薄膜.结果表明,在-1. 0V~+1. 8V(vs.Ag/AgCl)扫描电位之间形成的薄膜具有较高的电活性和稳定性.该电极对抗坏血酸电化学氧化有催化作用,既使抗坏血酸的氧化电位负移了 270mV,又增大了其氧化峰电流.催化峰电流与抗坏血酸浓度在 2. 5~250μg/mL范围内呈良好的线性关系.     

聚刚果红修饰玻碳电极的制备及其电催化性能

在含刚果红的硼砂缓冲溶液中,用循环伏安法扫描,在玻碳电极上形成聚合物薄膜.在 -0. 8V~+1. 8V(vsAg/AgCl)的扫描电位范围形成的薄膜具有较高的电活性和稳定性.该电极对抗坏血酸、邻苯二酚的电化学氧化有催化作用,增大了氧化峰电流.催化峰电流与抗坏血酸和邻苯二酚浓度分别在 20 ~1 200mmol/L, 50 ~2 000mmol/L范围内呈良好的线性关系.     

表面等离子体共振技术与循环伏安法联用检测甲苯胺蓝

将表面等离子体共振技术(SPR) 与循环伏安法(CV) 联用, 并用小波变换提取实验数据, 实现了甲苯胺蓝的定量检测. 以传感片上的金膜为SPR测量基底, 并作为电化学的工作电极, 以Ag/AgCl电极(饱和KCl) 为参比电极, 以铂丝为对电极, 同时进行SPR扫描和循环伏安法扫描, 发现电化学聚合导致甲苯胺蓝氧化峰峰电位正移, 还原峰峰电位不变, 而SPR响应也整体下降; 将SPR响应对电位求导后进而对电位作图, 经小波变换处理后, 发现波谱峰电位接近循环伏安法氧化还原法电位. 利用该方法检测甲苯胺蓝的检出限与采用循环伏安法检测甲苯胺蓝的检出限在一个数量级上.     

阿昔洛韦在硼掺杂金刚石电极上的电化学行为及其与DNA相互作用的研究

利用硼掺杂金刚石(BDD)电极通过循环伏安法和微分脉冲伏安法研究了阿昔洛韦在0.10 mol/L磷酸盐缓冲溶液(pH 7.4)中的电化学行为及其与DNA的相互作用.与玻碳电极相比,阿昔洛韦在BDD电极上的循环伏安曲线在1.17 V处的氧化峰电流更大,背景电流较低.根据峰电位随溶液pH值和扫描速率的变化趋势考察了阿昔洛韦...     

没食子酸在电活化玻碳电极上的电化学行为及测定

采用循环伏安法和线性扫描伏安法对没食子酸在电活化玻碳电极上的电化学行为进行了研究。玻碳电极在pH7.0的磷酸盐缓冲溶液中,用恒电位法在1.7 V电位阳极氧化400 s。然后在pH3.0的柠檬酸盐缓冲溶液中,没食子酸在0.479 V和0.442 V处有一良好的氧化还原峰,在0.02～0.40 V s-1范围内,其氧化峰电流与扫描速率呈良好线性关系,表明电极过程为受吸附控制的准可逆过程。线性循环伏安法的氧化峰电流与没食子酸浓度1×10-6～1×10-4mol L-1范围内呈良好的线性关系(r=0.980 6),检出限为7.6×10-7mol L-1(S/N=3)。该方法操作简便,重现性较好,并应用此法分析了健民咽喉片剂中的没食子酸的含量。     

铜掺杂聚L-酪氨酸修饰电极同时测定尿酸、多巴胺和抗坏血酸

用循环伏安法制备铜掺杂聚L-酪氨酸修饰玻碳电极,研究了尿酸、抗坏血酸和多巴胺在修饰电极上的电化学行为,建立了同时测定尿酸、抗坏血酸和多巴胺的新方法.在pH 3.0磷酸盐缓冲溶液中,扫描速率为140 mV/s,多巴胺在修饰电极上产生一对氧化还原峰,峰电位分别为0.502 V、0.370 V,尿酸和抗坏血酸分别产生一氧化峰...     

磷钼酸修饰的铂电极对二甲醚氧化的电催化作用

利用循环伏安扫描法制备了磷钼酸(H3PMo12O40)修饰的铂电极.在制备修饰电极时,随着扫描次数的增加,磷钼酸的氧化还原峰电流增大,但最终获得稳定的重现性好的磷钼酸修饰的铂电极.通过循环伏安法研究了该修饰电极对二甲醚氧化的电催化反应.结果表明,与未修饰的铂电极相比,磷钼酸修饰的铂电极电催化氧化二甲醚的起始氧化电位负移50 mV,氧化峰电位负移35 mV,氧化峰电流密度提高了1.86倍,这表明修饰电极的电催化活性有了很大的提高.同时,电位负扫时,二甲醚在425 mV(vsSCE)处出现氧化峰,表明二甲醚在修饰电极上的电氧化机理可能发生了改变.实验还发现,制备修饰电极时,降低扫速会提高还原物质杂多蓝的吸附量,但过多的修饰物质会降低铂的活性位数目,反而降低了对二甲醚氧化的电催化作用.     

灿烂甲酚蓝的伏安性能

灿烂甲酚蓝(Brillant Cresyl Blue)结构式为: 可作为氧化还原指示剂。未见其极谱研究的报导。本文发现灿烂甲酚蓝在Britton-Robinson缓冲溶液中,在pH2.55时可产生一个氧化波和两个还原波,半波电位分别为:-0.09、-0.25、-0.42V(对当量Hg_2SO_4 电极)。进而用普通极谱、脉冲极谱、循环伏安法研究了它的伏安行为。由实验结果确定了各波的性质,测定了还原态的表观离解常数,讨论了电还原机理。实验部分国产883型极谱仪;79-1型伏安分析仪(济南无线电四厂);FA-1型伏安仪(本所自制);LZ3-204型函数记录仪(上海自动化仪表二厂);ATA-1A型旋转圆盘电极(江苏电分析仪     

双酚A在氮掺杂多壁碳纳米管修饰电极上的电化学行为及测定

构建了不同百分含量的氮掺杂的多壁碳纳米管化学修饰石墨电极,利用线性扫描伏安法及循环伏安法研究了双酚A(BPA)在修饰电极上的电化学行为。提出了一种灵敏、简便的直接检测双酚A的电化学分析方法。在pH6.98的PBS缓冲溶液中,在电位0.20 V富集后,该修饰电极在0.680 V出现一个灵敏的、峰形好的氧化峰。表明氮掺杂多壁碳纳米管薄膜对双酚A的氧化表现出一定的催化作用,能显著提高双酚A的氧化峰电流。在优化条件下,采用线性扫描伏安法对双酚A进行测定。双酚A的氧化峰电流与其浓度在2.5×10-7～1.0×10-4 mol/L之间有很好的线性关系(R为0.996),检出限为5.0×10-8mol/L。电极已初步用于实际样品中BPA的测定。     

烟酰胺辅酶在聚甲苯胺蓝膜修饰的玻碳电极上的电催化氧化

用循环伏安法在玻碳电极上电沉积一层稳定的甲苯胺蓝聚合物膜 ,研究了这层膜在 0 .2mol/L磷酸缓冲溶液 (pH 6 .86 )中的电化学性质 ,并且考察了该膜修饰的玻碳电极对烟酰胺辅酶 (NADH)的电催化作用 ,用旋转圆盘电极测量了NADH在该修饰电极上的催化反应常数。实验发现 ,在该修饰电极上 ,NADH氧化峰电位比未修饰的玻碳电极负移了 4 5 0mV ,且其催化反应速率常数为 3.5× 10 3 L·mol-1·s-1,说明聚甲苯胺蓝膜对NADH有良好的电催化作用     

A novel amperometric sensor for the determination of nitric oxide, and its application in rat liver cells

A novel amperometric nitric oxide sensor with a wide linear range, low detection limit and fast response time was developed. The sensor was fabricated using a poly-brilliant cresyl blue (PBCB)/Nafion film modified glassy carbon electrode (GCE). The PBCB on the working GCE surface dramatically improves the oxidation response of nitric oxide and lowers the required potential for the two-step oxidation of NO. Otherwise, Nafion coated onto the film electrode surface does not only improve the selectivity of the sensor, but also further lowers the active energy of the direct three-electron oxidation of NO to nitrate. The effect of the preanodic time and the film thickness of the electropolymerization on the nitric oxide response as well as the volume of Nafion coated onto the surface and the potential for amperometric detection were optimized. This novel sensor has been applied to the determination of NO released from rat liver cells, and the result is satisfactory. Correspondence: Sheng Shui Hu, Department of Chemistry, Wuhan University, Wuhan 430072, P.R. China     

Functionalized Multiwalled Carbon Nanotubes Through In Situ Electropolymerization of Brilliant Cresyl Blue for Determination of Epinephrine

In this work, a polymeric brilliant cresyl blue (BCB) and dihexadecyl phosphate (DHP) dispersed Multi‐walled carbon nanotubes (MWNTs) composite film modified glass carbon electrode (PBCB‐MWNTs‐DHP/GCE) denoted as epinephrine (EP) sensor was prepared by an in‐situ electropolymerization method. The electrochemical response of EP at the sensor is much better. Voltammetric investigations indicated that the improved response of EP at the sensor mainly arose from the enhanced adsorption of EP at PBCB‐MWNTs‐DHP film, perhaps through the hydrogen bonding and π–π interactions between EP and PBCB. The sensor was applied to the determination of EP in injection by a standard addition method and the results were satisfied.     

Polymer/Iron Oxide Nanoparticle Modified Glassy Carbon Electrodes for the Enhanced Detection of Epinephrine

Novel electrochemical sensors for epinephrine (EP) based on a glassy carbon electrode (GCE) modified with a redox polymer film and iron (III) oxide nanoparticles (Fe₂O₃NP) have been developed. Two redox polymers‐poly(brilliant cresyl blue) (PBCB) and poly(Nile blue) (PNB), and two different architectures‐polymer/Fe₂O₃/GCE and Fe₂O₃/polymer/GCE were investigated. The electrochemical oxidation of epinephrine at the modified electrodes was performed by differential pulse voltammetry (DPV), in pH 7 electrolyte, and the analytical parameters were determined. The results show enhanced performance, more sensitive responses and lower detection limits at the modified electrodes, compared to other electrochemical epinephrine sensors reported in the literature. The best voltammetric response with the lowest detection limit was obtained for the determination of epinephrine at PBCB/Fe₂O₃/GCE. The novel sensors are reusable, with good reproducibility and stability, and were successfully applied to the determination of epinephrine in commercial injectable adrenaline samples.     

Electrochemical Preparation of Brilliant‐Blue‐Modified Poly(diallyldimethylammonium Chloride) and Nafion‐Coated Glassy Carbon Electrodes and Their Electrocatalytic Behavior Towards Oxygen and L‐Cysteine

Brilliant blue FCF‐modified glassy carbon electrodes have been prepared by cycling the Nafion (or poly(diallyldimethylammonium chloride) (PDDAC)) coated electrodes repeatedly 15 cycles in brilliant blue FCF (BB FCF) dye solution. The BB FCF molecules are incorporated into Nafion coating by cycling the film‐covered electrode between +0.3 to 1.2 V (vs. Ag/AgCl) in pH 1.5 BB FCF solution while PDDAC‐coated electrode cycled between 0 to ?1.0 V (vs. Ag/AgCl) in pH 6.5 BB FCF solution to immobilize the dye. Electrostatic interaction between dye molecule and PDDAC was predominant in PDDAC coating whereas immobilization of dye in Nafion film attributed to the combined effect of electrostatic and hydrophobic interactions. The voltammetric features of BB FCF‐modified electrodes resemble that of surface‐confined redox couples. The peak potentials of BB FCF‐incorporated PDDAC‐coated electrode were shifted to more positive potential region with decreasing pH of contacting solution. BB FCF‐modified electrodes showed electrocatalytic activity towards reduction of oxygen and oxidation of L ‐cysteine with significant decease of overvoltage compared to unmodified electrode. The BB FCF‐modified Nafion‐coated electrode was tested for its analytical applications toward determination of L ‐cysteine. The linear range of calibration plot at BB FCF‐modified Nafion‐coated electrode is 10 to 100 μM, which coincides with L ‐cysteine levels in biological fluids. Sensitivity and detection limit of the electrode are 111 nA μM^?1 and 0.5 μM, respectively.     

Electrochemical preparation of composite of poly brilliant cresyl blue (PBCB)–poly 5-amino-2-napthalenesulfonic acid electrode and electrocatalytic application

Poly brilliant cresyl blue (PBCB) and poly 5-amino-2-napthalenesulfonic (PANS) polymer composite modified electrode was fabricated by the electrochemical polymerization of brilliant cresyl blue and 5-amino-2-napthalenesulfonic acid. When compared polymer composite electrodes with PBCB and PANS electrode, it showed enhanced electrochemical property. The morphology of the resulting composite electrode was characterized by AFM, and the electrochemical properties of the modified electrode were characterized by cyclic voltammetry and amperometry. The composite electrode showed surface-confined and pH-dependent electrochemical property. The composite electrode exhibited high catalytic behavior toward the reduction of hydrogen peroxide at low overpotential. The detection limit and sensitivity of the electrode toward H₂O₂ detection was 5 μM and 1 μA/mM, respectively, and response time was less than 10 s for hydrogen peroxide.     

铋膜修饰玻碳电极用于线性扫描溶出伏安法测定铝箔中痕量镓

用电化学沉积法将铋离子修饰在玻碳电极上,应用此铋膜修饰玻碳电极测定镓时,将试液在pH 5.4的六次甲基四胺-盐酸缓冲溶液中在-1.30 V处预还原40 s,然后在-1.30~-0.50 V范围内扫描,使镓离子从修饰电极上溶出,实现了镓离子的溶出伏安法测定,在-1.01 V处可得镓离子的氧化峰电位,镓的质量浓度在0.002 8~0.21μg.L-1范围内与其峰电流值呈线性关系,方法的检出限(3S/N)为0.7 ng.L-1。方法用于测定铝箔中镓的含量,加标回收率在98.2%~103.8%之间。     

Electrochemical polymerization of toluidine blue o and its electrocatalytic activity toward NADH oxidation

A stable electroactive thin film of poly(toluidine blue o) (PTOB) has been deposited on the surface of a glassy carbon electrode by cyclic voltammetry from an aqueous solution containing toluidine blue o (TOB). Cyclic voltammograms of PTOB indicate the presence of two redox couples and the formal potential shifts linearly in the negative direction with increasing solution pH with a slope of 58 and 54 mV per pH unit for couple I and couple II, respectively. The PTOB modified glassy carbon electrode shows electrocatalytic activity toward NADH oxidation in phosphate buffer solution (pH 7.0), with an overpotential ca. 470 mV lower than that of the bare electrode. The catalytic rate constant of the modified glassy carbon electrode for the oxidation of NADH is determined by cyclic voltammetry and rotating disk electrode measurements. The experimental results indicate that the electrode can be used as a detector for NADH determination with a linear range of 5.0×10⁻⁶ to 2.0×10⁻³ mol l⁻¹ and the detection limits of (5.0±0.3)×10⁻⁷ mol l⁻¹ at optimal conditions.     

pMB/MWNTs/GC电极对水体中苯二酚异构体的同时测定

通过在多壁碳纳米管修饰玻碳电极上电聚合亚甲基蓝,制备了聚亚甲基蓝/碳纳米管/玻碳电极(pMB/MWNTs/GC)。用循环伏安法研究了3种苯二酚异构体在该电极上的电化学行为,结果表明,在pH7.0的磷酸盐缓冲溶液中,该修饰电极对苯二酚异构体的氧化表现出优异的电催化性能和选择性,对苯二酚、邻苯二酚和间苯二酚的氧化峰分别为0.104、0.203、0.609 V(vs.SCE),峰电位差值分别为99、406 mV。基于苯二酚异构体在pMB/MWNTs/GC修饰电极上的伏安行为,建立了苯二酚3种异构体同时分析的新方法。考察了各影响因素对测定的影响,最优实验条件下,在5.0×10-6~1.5×10-4mol.L-1范围内,3种苯二酚异构体的阳极峰电流与其浓度存在线性关系,检出限均为1.0×10-6mol.L-1。将该法用于水体及冲洗废液中苯二酚异构体含量的测定,结果满意。     

Electropreparation of Poly(benzophenone‐4) Film Modified Electrode and Its Electrocatalytic Behavior Towards Dopamine,Ascorbic Acid and Nitrite

The oxidation of benzophenone‐4 (2‐hydroxy‐4‐methoxybenzophenone‐5‐sulfonic acid) at glassy carbon electrode gives rise to stable redox active electropolymerized film during repetitive potential cycling between 0 to 1.3 V (Ag/AgCl). Cyclic voltammogram of poly(benzophenone‐4) film shows a redox couple with well‐defined peaks. The redox response of the modified electrode was found to be depending on the pH of the contacting solution. The peak potentials were shifted to a less positive region with increasing pH and the dependence of the peak potential was found to be 51 mV/pH. The electrocatalytic behavior of poly(benzophenone‐4) film modified electrode towards oxidation of dopamine, ascorbic acid and reduction of nitrite was investigated. The oxidation of dopamine and ascorbic acid occurred at less positive potential on poly(benzophenone‐4) film compared to bare glassy carbon electrode. For dopamine, the overpotential was reduced about 180 mV. Feasibility of utilizing poly(benzophenone‐4) film coated electrode in analytical estimation of dopamine, ascorbic acid and nitrite was also demonstrated.