甲基对硫磷在聚噻吩/纳米二氧化钛修饰玻碳电极上的电化学行为及其测定

用循环伏安法(CV)、线性扫描溶出伏安法(LSSV)研究了甲基对硫磷(MPT)在聚噻吩/纳米二氧化钛修饰玻碳电极(PTh-NTiO2/GCE)上的电化学行为.实验表明,该修饰电极能显著提高MPT的氧化还原峰电流,在B-R缓冲溶液(pH 5.72)中,于-0.662V( vs.SCE)处产生灵敏的不可逆还原峰,其峰电流与...     

阿昔洛韦在活化玻碳电极上的电化学行为及其分析应用

采用循环伏安法和微分脉冲溶出伏安法对抗病毒药阿昔洛韦在活化玻碳电极上的电化学行为进行了研究.玻碳电极在1.0 mol·L-1氢氧化钠溶液中,用循环伏安法在0.5～1.5 V电位范围内活化500 S,在pH 3.0的B-R缓冲溶液中,阿昔洛韦在1.25 V(对Ag/AgCl)处有一良好的氧化峰,线性范围为5.0×10-7～1.0×10-5mol·L-1,检出限(3S/N)为1.7×10-7mol·L-1,比非活化玻碳电极测定降低了约12倍,应用此法分析了阿昔洛韦片剂中阿昔洛韦的含量,测得结果与分光光度法测得的结果相符.     

多孔钛基掺硼金刚石电极结构对电催化降解阿司匹林性能的影响

利用扫描电子显微镜(SEM)和X射线衍射仪(XRD)对多孔Ti/BDD电极及传统平板Ti/BDD(BDD=钛基掺硼金刚石)电极进行了研究,通过循环伏安法考察了电极的背景电流和电化学窗口.以阿司匹林为模型污染物,研究了BDD电极结构对阿司匹林电催化降解的影响.结果表明,多孔Ti/BDD电极的总带电量,内、外部带电量,孔隙率和比表面积均高于平板Ti/BDD电极;多孔Ti/BDD在对COD和阿司匹林的去除率和能量消耗等方面均优于平板Ti/BDD电极.     

磷钨酸/乙炔黑修饰电极上的阿昔洛韦电化学行为及其测定

本文制备了磷钨酸/乙炔黑修饰电极(PTA/AB/GCE),用循环伏安法(CV)研究了阿昔洛韦(ACV)在该修饰电极上的循环伏安行为。结果表明在pH 6.0的磷酸盐缓冲液中,ACV在该修饰电极上出现一明显的氧化峰。在60～220mV.s-1扫速范围内,其氧化峰电流(Ipa)与扫速平方根(v1/2)呈线性关系,表明该电极过程是受扩散控制的不可逆过程。计算了电极过程的部分动力学参数:电极有效面积为0.06902cm2,转移电子数为2,扩散系数为2.063×10-6cm2.s-1。运用方波溶出伏安法测定不同浓度ACV的方波溶出伏安曲线,结果表明氧化峰电流(Ipa)与ACV浓度在7.8×10-7～1.0×10-4mol.L-1范围内呈良好线性关系(r=0.9924),检出限(S/N=3)为3.1×10-7mol.L-1,加标回收率为95.69%～107.2%。     

6-取代嘌呤的电化学行为及与DNA的相互作用

应用循环伏安法和微分脉冲伏安法研究了6-糠氨基嘌呤(6-KT)和6-巯基嘌呤(6-MP)在汞电极上的电化学行为及与小牛胸腺DNA的相互作用.结果发现,6-KT和6-MP的循环伏安曲线均显示两对分别表征为扩散控制和吸附控制的氧化还原波.扩散控制波的氧化峰电流随6-取代嘌呤浓度在0.1~50.0μmol.L-1范围内呈现良好的线性关系.依据预吸附时间和溶液pH值对吸附控制波的还原峰电位和峰电流的影响,讨论了6-KT和6-MP在汞电极上的吸附机理.作者认为,6-KT乃通过部分插入作用与DNA结合,而6-MP与DNA间的相互作用为静电模式.     

6-糠氨基嘌呤的电化学行为及与DNA的相互作用

应用循环伏安法、微分脉冲伏安法和紫外光谱法研究了6-糠氨基嘌呤(6-KT)在汞电极上的电化学行为及与小牛胸腺DNA的相互作用.结果发现,6-KT的循环伏安曲线显示两对表征为扩散控制和吸附控制的氧化还原波.扩散控制波的氧化峰电流随6-KT浓度在1.00×10-4～5.00×10-2mmol·L-1范围内呈现良好的线性关系.依据预吸附时间和溶液pH值对吸附控制波的还原峰电位和峰电流的影响,讨论了6-KT在汞电极上的吸附机理.另外,6-KT的扩散控制波的还原峰电流随DNA浓度的增加而减小,峰电位正移,紫外吸收峰出现明显的减色效应,认为6-KT乃通过部分插入作用与DNA结合,结合常数为2.60×103 L·mol-1.     

6-苄氨基嘌呤的电化学行为及与DNA的相互作用

应用循环伏安法、微分脉冲伏安法和紫外光谱法研究了6-苄氨基嘌呤(6-BA)在汞电极上的电化学行为,及与小牛胸腺DNA的相互作用.结果发现,6-BA的循环伏安曲线显示三对扩散或吸附控制的氧化还原波.扩散波的氧化峰电流随6-BA浓度在0.1～50.0 μmol·L-1范围内呈现良好的线性关系.依据预吸附时间和溶液pH值对吸附波的还原峰电位和峰电流的影响,讨论了6-BA在汞电极上的咐附机理.另外,6-BA的还原峰电流随DNA浓度的增加而减小,峰电位正移,紫外吸收峰出现明显的减色效应,认为6-BA通过部分插入作用与DNA结合,结合常数为2.3×103L·mol-1.     

药物分子在玻碳电极上的电分析化学研究——Ⅳ.乙酰螺旋霉素的伏安测定

本文对乙酰螺旋霉素在GCE上的伏安行为进行了研究,发现在磷酸盐缓冲溶液(pH=7.87)中,於十0.85V(vs.Ag/AgCl)左右产生一良好的阳极氧化伏安峰.浓度在0.5～100μg/mL之间与峰电流呈线性关系,分析了制剂中乙酰螺旋霉素的含量,相对标准偏差为4.5%,平均回收率为101%.经循环伏安法验证,电极反应为不可逆反应.     

微分脉冲伏安法用于血液中两种核苷类抗病毒药物的同时测定

采用微分脉冲伏安法考察了两种核苷类抗病毒药物阿昔洛韦(aciclovir)和喷昔洛韦(penciclovir)在乙二胺修饰的玻碳电极上的电化学行为及其在代谢血样中的同时测定方法,并探讨了电极修饰和电极反应的机理。在pH2.56的Britton-Robinson缓冲溶液中,阿昔洛韦和喷昔洛韦在乙二胺修饰的玻碳电极上均有一灵敏的不可逆氧化峰,峰电位分别为1.20和1.17 V。在优化的实验条件下,阿昔洛韦和喷昔洛韦分别在0.20~4.0 mg/L和0.02~0.40 mg/L浓度范围内与峰电流呈线性关系,其检出限分别为77和12μg/L。引入化学计量学方法对其混合组分的伏安谱进行解析,实现了两组分的同时测定,并对小鼠血液中代谢的两种核苷类抗病毒药物进行了同时测定。     

聚灿烂甲酚蓝修饰玻碳电极的制备及电化学性质

在含灿烂甲酚蓝的磷酸缓冲溶液中,用循环伏安法扫描.在经预处理的玻碳电极上形成了聚合物薄膜.在-0.7V-+0.9V(vsSCE)的扫描电位范围和弱碱性介质中形成的薄膜具有较高电活性和稳定性.制备好的聚灿烂甲酚蓝修饰电极在磷酸缓冲溶液的循环伏安曲线有两对氧化还原峰,峰电位随pH升高而向负电位方向移动.该电极对NADH的电化学氧化有催化作用,使其氧化电位负移了270mV并增大了氧化峰电流.     

Comparison of Boron‐Doped Diamond and Glassy Carbon Electrodes for Determination of Procaine Hydrochloride

The electrochemical oxidation of procaine hydrochloride (PC?HCL, 2‐diethylaminoethyl 4‐aminobenzoate hydrochloride) was investigated at as‐deposited boron‐doped diamond (ad‐BDD) electrode, anodically oxidized BDD (ao‐BDD) electrode and glassy carbon (GC) electrode using cyclic voltammetry (CV). Well‐defined cyclic voltammograms were obtained for PC?HCL oxidation with high signal‐to‐background (S/B) ratio, low tendency for adsorption, good reproducibility and long‐term stability at ad‐BDD electrode, demonstrating its superior electrochemical behavior and significant advantages in contrast to ao‐BDD and GC electrode. At 100 μM PC?HCL, the voltammetric S/B ratio was nearly one order of magnitude higher at an ad‐BDD electrode than that at a GC electrode. In a separate set of experiments for oxidation of 100 μM PC?HCL, 96%, 92% and 84% of the initial oxidation peak current was retained at the ad‐BDD, ao‐BDD and GC electrode, respectively, by stirring the solution after the tenth cycle. The current response was linearly proportional to the square root of the scan rate within the range 10–1000 mV s^?1 in 10 μM PC?HCL solutions, indicating that the oxidation process was diffusion‐controlled with negligible adsorption at an ad‐BDD surface. The good linearity was observed for a concentration range from 5 to 200 μM with a linear equation of y=0.03517x+0.65346 (r=0.999), and the detection limit was 0.5 μM for oxidation of PC?HCL at the ad‐BDD electrode. The ad‐BDD electrode could maintain 100% of its original activity after intermittent use for 3 months.     

苏丹红I号在纳米金/碳球修饰硼掺杂金刚石电极上的电化学行为

采用纳米金/碳球(Au/CS)复合物修饰硼掺杂金刚石(BDD)电极,研究了苏丹红I号在Au/CS修饰BDD电极上的电化学行为,并据此建立了实际样品中的苏丹红I号的测定方法.结果表明,与裸BDD电极相比,苏丹红I号在Au/CS修饰BDD电极上的氧化峰电流由0.24μA增加到0.83μA,峰电位由0.809V负移到0.743V.在最优测试条件下,苏丹红I号浓度与其峰电流在4~100μmol/L范围内呈线性关系,线性方程为Ip=0.011 26c+0.116(R2=0.999),检出限为8.33μmol/L.采用本方法对实际样品中的苏丹红I号进行测定,测定结果及平均回收率均优于BDD电极法.     

Studies on electrochemical behaviors of acyclovir and its voltammetric determination with nano-structured film electrode

A multi-wall carbon nanotubes (MWNTs)-dihexadecyl hydrogen phosphate (DHP) film-coated glassy carbon electrode (GCE) was fabricated, and the electrochemical behaviors of acyclovir on the MWNTs-DHP film-coated GCE were investigated by using cyclic voltammetry (CV), linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS) and chronocoulometry (CC). The oxidation peak current of acyclovir increased significantly and the peak potential shifted negatively at the MWNTs-DHP film-modified GCE, compared with that at a bare GCE. The results showed that this nano-structured film electrode exhibited excellent enhancement effects on the electrochemical oxidation of acyclovir. Consequently, a simple and sensitive electroanalytical method was developed for the determination of acyclovir. The oxidation peak current was proportional to the concentration of acyclovir from 8.0 × 10⁻⁸ to 1.0 × 10⁻⁵ mol/L. The detection limit was about 3.0 × 10⁻⁸ mol/L for 60 s accumulation at 0.00 V. The proposed method was demonstrated by using acyclovir tablets and the result was satisfying.     

Electrochemical behaviors of native and thermally denatured fish DNA in the presence of cytosine derivatives and porphyrin by cyclic voltammetry using boron-doped diamond electrode

The electrochemical behaviors of native and thermally denatured fish DNA was investigated using boron-doped diamond (BDD) film electrode by cyclic voltammetry. The BDD electrode afforded us to measure weak current less than muA for the DNA solution in 100 microl. The mixture of acetic acid and sodium acetate solution (0.2 M) was used as a supporting electrolyte. Two oxidation peaks were observed at about +1.1 V and +1.3 V at pH 4.6 for thermally denatured fish DNA. This is due to the oxidation of guanine and adenine in the denatured fish DNA, respectively. In contrast, the native fish DNA showed ill-defined peaks at +1.1 V. Furthermore, the electrochemical behaviors of thermally denatured fish DNA were studied in the presence of cytosine, cytidine, cytidine-5-monophosphate, tetrakis(1-methypyridinium-4-yl)porphyrin (H(2)(TMPyP)(4+)) and Ru(II)(TMPyP)(4+). The oxidation peak intensity at +1.1 V gradually decreased with the increase of the concentrations of the above compounds. Based on the above studies, electrochemical behaviors of the thermally denatured fish DNA at BDD electrode is discussed.     

Anodic Oxidation Behaviors of Formaldehyde at Boron‐Doped Diamond Electrodes

The electrochemical behaviors of formaldehyde (FA) at boron‐doped diamond (BDD) electrodes are investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and linear scanning voltammetry (LSV) techniques. The CV results show that the oxidation reaction of FA is influenced by the hydroxyl concentration in the solution, and the peak current response with the FA concentration is linear at the range from 10 to 100 mM. The differential capacitance from EIS results indicate that the FA molecules adsorb at the BDD electrode surface at low potential (from 1.0 to 1.4 V). The kinetic studies have been examined with the various concentrations of FA, pH, and temperature. The activation energy of FA oxidation is also calculated. The results of kinetic study indicate that the adsorption of FA molecules at the BDD electrode is the rate‐determining step at low potential (from 1.0 to 1.40 V).     

Ta/BDD薄膜电极电化学催化氧化硝基酚

研究了热丝化学气相沉积法(HFCVD)制备得到钽衬底掺硼金刚石膜电极(Ta/BDD)的物理性质和电势窗口, 并考察了其用于电化学催化氧化硝基酚过程中的性能及各种影响因素. 扫描电镜和拉曼光谱表明, Ta/BDD电极具有良好的物理性能, 通过测试Ta/BDD电势窗口发现, 该电极具有较高的析氧过电位. 在Ta/BDD电化学催化氧化硝基酚过程中, 化学需氧量(COD)和高效液相色谱测试表明, 硝基酚能够有效降解, 电流密度、支持电解液及浓度对降解过程影响较大, 温度影响不明显. 强化寿命实验表明, Ta/BDD电极具有较好的稳定性. 实验结果表明, Ta/BDD电极是一种适于硝基酚降解和COD去除的优良电极.     

Hydroxyl radicals electrochemically generated in situ on a boron-doped diamond electrode

The hydroxyl radicals electrochemically generated in situ on a boron-doped diamond (BDD) electrode have been investigated for the first time in different electrolyte media, over the whole pH range between 1 and 11. A more extensive characterisation of BDD electrochemical properties is very important to understand the reactivity of organic compounds towards electrochemical oxidation on the BDD electrode, which is related to their interaction with adsorbed hydroxyl radicals due to water oxidation on the electrode surface. An oxidation peak corresponding to the transfer of one electron and one proton was observed in pH <9 electrolytes, associated with the water discharge process and electrochemical generation of hydroxyl radicals, which can interact and enhance the electro-oxidation of organic compounds. In pH >9 electrolytes the electrochemical generation of hydroxyl radicals was not observed; ammonia buffer electrolyte gave a pH-independent peak corresponding to the ammonia oxidation reaction. Additionally, for most pH values studied, a few small peaks associated with the electrochemical interaction between non-diamond carbon species on the doped diamond electrode surface and the electrolyte were also seen, which suggests that the doped diamond is relatively unreactive, but not completely inert, and the electrogenerated hydroxyl radicals play a role as mediator in the oxidation of organics.     

Sensitive Electrochemical Detection of Oxalate at a Positively Charged Boron‐Doped Diamond Surface

Allyltriethylammonium bromide (ATAB) was covalently attached to the surface of hydrogen‐terminated boron‐doped diamond (BDD) thin films using a photochemical method to fabricate positively charged electrode surfaces. The anodic current for oxalate oxidation both in cyclic voltammetry and in flow‐injection analysis with amperometry was found to be up to two times larger at ATAB‐modified BDD (ATAB‐BDD) than at an unmodified BDD electrode, which may be based on the electrostatic interaction between the oxalate anion and the electrode surface. In addition, the stability of the electrochemical detection of oxalate was improved at the ATAB‐BDD electrode compared to the unmodified electrode.     

Electroanalysis of tetracycline using nickel-implanted boron-doped diamond thin film electrode applied to flow injection system.

The electrochemical analysis of tetracycline was investigated using nickel-implanted boron-doped diamond thin film electrode by cyclic voltammetry and amperometry with a flow injection system. Cyclic voltammetry was used to study the electrochemical oxidation of tetracycline. Comparison experiments were carried out using as-deposited boron-doped diamond thin film electrode (BDD). Nickel-implanted boron-doped diamond thin film electrode (Ni-DIA) provided well-resolved oxidation irreversible cyclic voltammograms. The current signals were higher than those obtained using the as-deposited BDD electrode. Results using nickel-implanted boron-doped diamond thin film electrode in flow injection system coupled with amperometric detection are presented. The optimum potential for tetracycline was 1.55 V versus Ag/AgCl. The linear range of 1.0 to 100 microM and the detection limit of 10 nM were obtained. In addition, the application for drug formulation was also investigated.     

Electrochemical oxidation and determination of methylparaben at overoxidized polypyrrole film modified a boron-doped diamond electrode

Electrochemical oxidation of methylparaben (MP) is studied on an overoxidized polypyrrole (OPPy)-modified boron-doped diamond electrode using the cyclic voltammetry (CV) and square wave voltammetry (SWV) techniques. The OPPy-modified BDD electrode displays the catalytic activity of electrooxidation of methylparaben. The modification of BDD electrode surface results in higher values of recorded oxidation currents of the methylparaben than on a bare BDD electrode. The diffusion character of recorded current is determined on the basis of the relation between the current and the scan rate. The linear relationship between methylparaben oxidation peak current is obtained in the range 1.57?×?10^??6–2.06?×?10^??5 mol L^??1. A new voltammetric procedure is proposed to quantify methylparaben in cosmetic products using an overoxidized polypyrrole (OPPy)-modified BDD electrode. The results are compared to the HPLC technique described in the literature as the reference method.