PTT/PET共混体系晶体形态与结晶性能的研究

用差示扫描量热仪(DSC)、广角X射线衍射(WAXD)和正交偏光显微镜研究了聚对苯二甲酸丙二酯(PTT)和聚对苯二甲酸乙二酯(PET)共混体系的晶体形态与结晶性能.结果表明,共混体系结晶性能与PTT的含量有关.PET的加入,使共混体系的球晶尺寸减小.球晶完善性降低.当PTT含量为40wt%～60wt%时,共混物分别出现了双重熔融峰和双重结晶峰.双重熔融峰是加热过程中熔融重结晶造成的,双重结晶峰说明不完善的晶体产生的次级结晶.     

聚己内酯/硝基纤维素共混体系结晶行为的研究

通过对聚己内酯／硝基纤维素共混体系的热分析、傅立叶变换红外光谱的研究，证实了该共混体系在聚己内酯含量较高时，是一个热力学相容的体系，同时两组分之间存在强的氢键相互作用。在此体系中聚己内酯长成了清晰规整的环带球晶。聚己内酯结晶形态随结晶温度和共混物组成的变化表明，在共混体系中聚己内酯结晶速率与非晶第二组分的扩散速率存在一定的匹配关系，是影响环带球晶形成的重要因素。     

SSBR/TPI共混体系中TPI的结晶、成核及动力学研究

研究了不相容共混体系溶聚丁苯橡胶(SSBR)/反式-1,4-聚异戊二烯(TPI)共混体系的结晶行为.当SSBR含量较低时,SSBR/TPI共混物的成核密度降低,晶体生长速率降低,等温结晶速率降低,非等温结晶峰移向低温,SSBR抑制了α-TPI的生成,SSBR/TPI共混体系总结晶度降低,但TPI的相对结晶度升高,结晶行为与热力学相容的结晶/非晶共混体系一致;当SSBR含量较高时,随着SSBR含量增加,体系的成核密度增加,球晶的生长速率显著降低,SSBR显著抑制了α-TPI的生成,共混体系以β晶为主.     

PP/PMMA/PP-g-MAH共混物的结晶和相形态研究

采用偏光显微镜和相差显微镜详细研究PP/PMMA不相容聚合物共混物体系和PP/PMMA/PP-g-PMMA增容共混体系的结晶和相形态.偏光显微照片的研究结果表明,增容剂PP-g-MAH中PP结晶需要克服更多的能垒,导致PP结晶形态变得不完善,球晶尺寸变小.比较PP/PMMA和PP/PMMA/PP-g-MAH的相差显微照片可以看出,由于增容剂的加入,PP与PMMA相之间的界面变得模糊,两相的相容性变好.随着PP-g-MAH中MAH接枝率的增加,PMMA分散相的尺寸减小且变得均匀;当增容剂的接枝率为2.41%,添加的质量分数为4.71%,PP/PMMA共混体系中PMMA分散相的相?尺寸可达最小.PP-g-MAH作为反应型增容剂,一方面与PP在界面区域产生共晶;另一方面,MAH极性基团与PMMA的极性基团间产生的强的化学键合作用,使得界面区域的PP-g-MAH分子采取有利于降低构象熵的构象来起到增容作用.PP/PMMA共混物在130℃等温结晶的结果显示,PMMA相对PP的结晶形态的影响较小,PP结晶呈现典型的均相成核特征.PP/PMMA共混体系中加入PP-g-MAH,PP结晶尺寸减少.与非等温结晶相比,等温结晶的PP/PMMA共混物中PMMA相区尺寸明显偏大.     

聚己内酯/纳米二氧化硅复合体系环带球晶形貌及结晶行为研究

采用溶液浇铸的方法制备了聚己内酯(PCL)/疏水性纳米二氧化硅(R974)复合体系薄膜,利用偏光显微镜、差示扫描量热仪、扫描电镜等研究了R974对PCL环带球晶形貌及结晶行为的影响,并从微观层次探讨了PCL/R974环带球晶可能的形成机理。结果表明,PCL/R974环带球晶是由扭转生长的片晶构成。R974的加入可诱导PCL环带球晶的形成,拓宽环带球晶形成温度。R974含量越高,PCL形成环带温度越低,环带周期越小,环带结构越规整。等温结晶时,R974加入并未改变PCL异相成核机理,但会影响其结晶动力学。当R974含量≤4%(wt)时,其异相成核作用占主导,促进了PCL结晶过程;当R974含量4%(wt)时,其对于球晶生长的阻碍大于异相成核作用,最终抑制了PCL的结晶。     

双组分共混体系中晶相结晶行为

含结晶组分的双组分共混体系，其中的结晶组分的结晶行为会受到另一组分的影响，进而影响到材料的结构与性能。本文总结了近年来含结晶相的聚合物共混物在改性过程中，共混与添加组分对晶相结晶速率、晶型比例、晶体尺寸等结晶行为的影响。     

液晶聚芳醚酮/含甲基苯侧基聚芳醚酮共混体系的环带球晶

本文通过研究含氯侧基液晶聚芳醚酮/含甲基苯侧基聚芳醚酮共混体系(结晶/非晶)环带球晶的形态演变和发展过程; 利用选择性溶剂刻蚀方法确定共混体系环带球晶的相组成和相结构, 探讨了环带球晶的形成机理.     

聚左旋乳酸/聚消旋乳酸共混物的结晶行为

非晶态聚消旋乳酸(PDLLA)对PLLA的结晶行为有较大的影响。本文利用差示扫描量热仪(DSC)和偏光显微镜(POM)对不同分子量PLLA、PDLLA按不同比例制得的共混物结晶进行了系统研究。结果表明随PDLLA含量的增大PLLA冷结晶温度升高,且越接近熔融温度。PDLLA分子量较小时PLLA球晶特征被明显破坏,PDLLA分子量较大时PLLA更易形保持球晶特征且易形成环带球晶形貌,这与结晶速率与非晶组分的扩散速率匹配程度有关。低分子量的PDLLA使PLLA的最大生长速率对应的温度出现在较低温度。     

PEO分子量对POM/PEO晶/晶共混物溶液结晶的影响

以六氟异丙醇(HFIP)为聚甲醛(POM)与聚氧化乙烯(PEO)的共溶剂,通过溶液结晶研究了PEO分子量对POM/PEO 50/50晶/晶共混物结晶行为及结晶形态的影响。结果表明,PEO分子量越小,POM与PEO在结晶过程中相互干扰越大。当PEO分子量为4×103时,共混物中POM形成部分不完善晶体,出现明显的熔融双峰。SEM结果表明:含不同分子量PEO的共混晶体均无明显相分离,且低分子量PEO的共混物更易形成规整球晶,认为通过溶液结晶,POM/PEO 50/50共混物中POM与PEO形成了晶体相互穿插的结晶结构。     

聚碳酸亚丙酯对聚(β-羟基丁酸酯-β-羟基戊酸酯)结晶行为的影响

用FTIR和DSC研究了PHBV及其与聚碳酸亚丙酯(PPC)熔融共混样的熔融结晶行为和等温结晶动力学.结果表明,PHBV与PPC熔融共混过程中发生了酯交换反应,两组分间存在一定的相互作用.PPC虽然能降低PHBV结晶折迭链的表面自由能,但同时也能够降低PHBV的结晶度、球晶径向生长速率、平衡熔点和结晶能力.     

Effects of amorphous poly(vinyl acetate) on crystalline morphology of poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid)

The amorphous and crystalline phase behavior, spherulite morphology, and interactions between amorphous poly(vinyl acetate) (PVAc) and poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid) (PHBV) were examined using differential scanning calorimetry, polarized-light optical and scanning electron, atomic-force microscopy (DSC, POM, SEM, AFM), and small-angle X-ray scattering (SAXS). The PHBV/PVAc blend was found to be miscible with an almost linear T _g-composition relationship, indicating perfect homogeneity. Interaction parameter by melting point depression is a negative value of χ = −0.32, suggesting quite favorable interaction strength. With the intimate interaction between the amorphous PVAc and crystalline PHBV polymers, effects of PVAc on the spherulitic morphology of PHBV are quite significant. Owing to the higher T _g of PVAc (than that of PHBV), the spherulite growth rate of PHBV was depressed by increasing PVAc content in blends. Neat PHBV exhibits ring-banded spherulites when crystallized at T_c = 60 ~ 110^° C {T_{\rm{c}}} = {6}0\sim {11}0^\circ {\hbox{C}} ; however, with increasing PVAc content in the blends, the temperature range at which the PHBV/PVAc blends exhibit ring-banded spherulites remains similar but the regularity increases, and the inter-ring spacing significantly decreases. In addition, the spherulite size and ring-band patterns therein are strongly dependent on T _max (190 vs. 220 °C, respectively, for erasing prior nuclei), from which the blends were quenched to a T _c (60–110 °C) for crystallization. For PHBV/PVAc blends crystallized at the same T _c from different T _max, higher T _max tends to erase nuclei, leading to larger spherulites. However, such larger spherulites owing to higher T _max are not necessarily packed with thicker lamellae.     

Quantitative FTIR study of PHBV/bisphenol A blends

FTIR spectroscopy was used to verify the presence of intermolecular hydrogen bond (inter-H-bond) between poly(3-hydroxybutyrate co-3-hydroxyvalerate) (PHBV) and bisphenol A (BPA). By monitoring the spectral changes during PHBV crystallization and blends dissociation, the absorptivity ratio of CO bonds in crystalline and amorphous regions in PHBV and that of H-bonded and free CO in PHBV/BPA blends were experimentally determined as 1.40 and 1.68, respectively. Using curve-fitting program, the CO absorptions in spectra of blends were ascribed to three types of bonds: amorphous, crystalline and H-bonded CO. The crystallinity of PHBV and the fraction of H-bonded CO were calculated. These results indicated that the H-bond clearly suppressed the PHBV crystallization. Furthermore, the fraction of BPA molecules that simultaneously formed two hydrogen bonds (H-bonds) with CO was estimated. It revealed that there existed a H-bond network in PHBV/BPA blends. This network was compared with the covalent network by estimating the number of atoms between every two adjacent crosslink points in chain. Up to the high density of H-bond discussed in this paper, there was always a certain part in PHBV that crystallized due to the dynamic character of hydrogen bonds; however, the hydrogen bonds significantly reduced the crystallization rate of PHBV.     

异相成核和拉伸诱导对生物基PHBV复合纤维结晶结构与力学性能的影响

采用熔融纺丝法制备了聚(3-羟基丁酸酯-co-3-羟基戊酸酯)(PHBV)/二硫化钨(WS_2)复合纤维.利用示差扫描量热仪(DSC)、热台偏光显微镜、二维广角射线衍射仪(2D-WXRD)、纤维强力仪研究了WS_2异相成核作用和牵伸诱导作用对纤维的结晶结构和力学性能的影响.研究表明,WS_2显著提高了PHBV的结晶温度,当使用2 wt%WS_2时,复合材料的结晶温度提高到115~130oC,比纯PHBV(99~105oC)提高了约25oC.WS_2不仅没有影响PHBV球晶的径向生长速率,且明显提高了PHBV/WS_2复合材料的晶核密度,熔体成核活性Φ由1.0降低为0.49.随着牵伸倍率和WS_2用量的增加,纤维的拉伸强度呈现出先增加后减小的趋势.当添加1 wt%WS_2并采用单向牵伸3.8倍时,纤维中的晶体取向产生了β晶结构,使复合纤维的拉伸强度由纯PHBV的37 MPa提高至155 MPa,断裂伸长率由2.4%增加至45%.     

Nonisothermal crystallization behavior, and morphology of poly(trimethylene terephthalate)/polyethylene glycol copolymers

Poly(trimethylene terephthalate)/polyethylene glycol (PTT/PEG) copolymers, with PEG content ranging from 27.2 to 47.4 wt%, were synthesized by melt copolycondensation. Wide-Angle X-ray diffractometer revealed that all copolymers had the same crystal structure of homo-PTT at room temperature. All copolymers could form ring-banded spherulites, and band spacing increased with increasing PEG content at a given crystallization temperature. Nonisothermal crystallization morphology of copolymers was greatly influenced by cooling rate. When the cooling rate was 2.5 °C/min or lower, banded patterns were absent, whereas when the cooling rate was 20 °C/min or higher, a novel crystal morphology composed of non-banded spherulites (central part) and ring-banded spherulites with decreasing band spacing along the radial growth direction was observed. Moreover, the size of the non-banded spherulitic part decreased with increasing cooling rate. Finally, the nonisothermal crystallization kinetics of copolymers were analyzed and only the Mo method was satisfactory to accurately describe this system.     

Periodic radial growth in ring-banded spherulites of poly(ε-caprolactone)/poly(styrene-co-acrylonitrile) blends

The isothermal crystallization process of a PCL/SAN blend (90/10 wt.-%) was investigated by using real time image analysis and hot stage optical microscopy. It was found that the growth rate of ringbanded spherulites in the isothermal crystallization process is not constant. Slow growth occurs in the bright bands, while fast growth is found in the dark bands. The radially unequal growth rate of ring-banded spherulites in PCL/SAN blends may be related to the convex band structure on the surface. This new discovery gives us the idea that rhythmic growth is effective in the growth process of ring-banded spherulites.     

Composition distributions within poly(vinylidene fluoride) spherulites as grown in blends with poly(methyl methacrylate)

Upon crystalline solidification of one component in a homogeneously molten polymer blend, composition profiles develop outside (i.e., in the rest melt) and behind (i.e., within the spherulites) the crystal growth front. The present article is devoted to the detailed verification and the interpretation of these distributions and their temporal development inside growing spherulites. To this end, the energy dispersive X‐ray emission (EDX) of suitable elements has been recorded locally resolved in a scanning electron microscope and evaluated correspondingly. The investigations were performed at the melt homogeneous blend of poly(vinylidene fluoride) (PVDF) as crystallizing and poly(methyl methacrylate) (PMMA) as steadily amorphous component. If the spherulites are not volume filling, the mean PMMA content 〈?_PMMA〉 inside the PVDF spherulites is for all blends about 0.2 below the starting composition. ?_PMMA increases however slightly from the center of a spherulite to its border. That increase reflects the PMMA concentration in front of the spherulite surface, which increases likewise with time, and is clearly above the initial composition. There is at the spherulite surface, consequently, a remarkable jump in composition from the spherulite internal to its amorphous surroundings. It may amount up to 0.5. With volume filling spherulites, a slight variation of the composition from the center of a spherulite to its border is observed, too. This proves that also at these conditions composition profiles develop in the spherulite's surroundings. They remain however so weak that they do not inhibit crystallization even in its later stages. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 338–346, 2006     

Thermal behavior and phase behavior in blends of liquid crystalline poly(aryl ether ketone) and poly(aryl ether ether ketone) containing thioether units

Thermal behavior and phase behavior in blends of liquid crystalline poly(aryl ether ketone) with lateral methoxy groups (M-PAEK) and poly(aryl ether ether ketone) containing thioether units (S-PEEK) have been investigated by differential scanning calorimetry (DSC) and polarized light microscopy (PLM) techniques. The results indicate that the composition of the blends has great effect on the phase behavior and morphology. Thin films of pure M-PAEK and S-PEEK crystallized from the melts exhibit typical mosaic and spherulitic structures, respectively. For the blends with higher M-PAEK contents (> 50%), an unusual ring-banded spherulite with structural discontinuity is formed. The bright core and rings of the ring-banded spherulites under PLM are composed of M-PAEK phase, while the dark rings consist mainly of S-PEEK phase. For the 50:50 M-PAEK/S-PEEK blend, the ring-banded spherulites and S-PEEK spherulites coexist, which implies that a partial phase separation between the two components takes place in the melting state. In S-PEEK-rich blends, a volume-filled spherulite is produced. In addition, the effect of isothermal crystallization temperature on the phase behavior, especially the ring-banded spherulite formation in the blends, is discussed.     

新型sPS/PA6/SsPS-H塑料合金的性能和形态结构

研究新型sPS PA6 SsPS H塑料合金的力学性能和微观形态结构 .间规聚苯乙烯 (sPS)的磺化产物磺化间规聚苯乙烯 (SsPS H)的加入明显地改善了sPS PA6(聚酰胺 6)二组分合金的力学性能 ,在sPS PA6 SsPS H重量组成为 80 2 0 5时 ,三组分合金的冲击强度最大 ,为 1 5 6kJ m2 ,约为纯sPS冲击强度的 3倍 DMA和SEM结果表明 ,SsPS H对sPS和PA6共混有良好的增容作用 ,它起到了降低合金的微相尺寸和加强相间界面粘结的作用 .此外 ,FTIR结果还表明SsPS H和PA6之间存在特殊相互作用 ,其作用方式是通过SsPS H的磺酸基将其质子转移给PA6酰胺基的氮