Ag离子注入非晶SiO2的光学吸收、拉曼谱和透射电镜研究

能量为200keV的Ag离子,以1×1016,5×1016,1×1017cm-2的剂量分别注入到非晶SiO2玻璃,光学吸收谱显示:注入剂量为1×1016 cm-2的样品的光吸收谱为洛伦兹曲线,与Mie理论模拟的曲线形状一致;注入剂量较大的5×1016,1×1017 cm-2的谱线共振吸收增强,峰位红移并出现伴峰.透射电镜观察分析表明,注入剂量不同的样品中形成的纳米颗粒的大小、形状、分布都不同,注入剂量较大的还会产生明显的表面溅射效应,这些因素都会影响共振吸收的峰形、峰位和峰强.当注入剂量达到1×1017 cm-2时,Ag纳米颗粒内部可能还形成了杂质团簇.     

Al2O3薄膜/纳米Ag颗粒复合结构的光吸收谱及增强Raman散射光谱研究

Al₂O₃介质薄膜与纳米Ag颗粒构成的复合结构,被应用于表面增强Raman散射探测实验中,其中Al₂O₃介质薄膜对纳米Ag颗粒的吸收谱及增强Raman散射光谱的影响被特别关注.该复合结构的光学特性表征出纳米Ag颗粒的偶极振荡特性.从光吸收谱中可以看到,其共振吸收谱随Al₂O₃介质薄膜厚度增加而在整个谱域上发生红移,表明纳米Ag颗粒的周围介电常数随Al₂O₃介质薄膜厚度的增加而增大.采用罗丹明6G作为探针原子,6个Raman特征峰的平均增益值作为表征表面增强Raman散射衬底增益程度的量度.实验结果表明,Al₂O₃介质薄膜层的引入提高了纳米Ag颗粒的衬底介电常数,并引起了散射共振的增强,从而使表面增强Raman散射强度提高. 关键词： 纳米Ag薄膜 共振吸收 表面增强Raman散射 介电常数     

梯度掺杂与均匀掺杂GaN光电阴极的对比研究

为了提高负电子亲和势(NEA)GaN光电阴极的量子效率,利用金属有机化合物化学气相淀积(MOCVD)外延生长了梯度掺杂反射式GaN光电阴极,其掺杂浓度由体内到表面依次为1×10¹⁸ cm^-3,4×10¹⁷ cm^-3,2×10¹⁷ cm^-3和6×10¹⁶ cm^-3,每个掺杂浓度区域的厚度约为45 nm,总的厚度为180 nm.在超高真 关键词： NEA GaN光电阴极 梯度掺杂 量子效率 能带结构     

CF3CDCl2分子红外多光子光热吸收谱

本文报道用铂丝光热吸收池作为探测器得到了CF₃CDCI₂的红外多光子吸收谱。并发现在线性吸收谱中944cm^-1处的吸收峰在多光子吸收谱中分裂为947cm^-1和927cm^-1两个吸收峰。这一现象与科里奥利力和非谐性引起的简正振动的耦合作用有关。这样,在用CF₃CDCI₂/CF₃CHCI₂体系分离氘同位素时,可以根据这一新结果选择更合适的激发波长。实验还发现在线性吸收谱中986cm^-1处的吸收峰在多光子吸收谱中出现约6cm^-2的红移。这种红移现象起源于分子振动能级的非谐性。 关键词：     

Ag-AAO纳米有序阵列复合结构等离子共振吸收特性研究

研究了Ag-AAO纳米有序阵列复合结构的等离子共振吸收特性。结果显示,Ag表面等离子共振吸收峰位于λ=352-377nm范围内,且可通过控制Ag纳米粒子的长径比使其吸收特性发生改变。若长径比增加,吸收峰位蓝移,强度增大,峰形变锐;反之,若长径比减少,吸收峰位红移,强度减弱,峰形逐渐宽化;运用麦克斯韦-加尼特（M-G）理论模拟的计算结果与实验规律基本相符,并较好地阐释了Ag表面等离子共振吸收峰的频移与其纳米粒子长径比之间的一些依赖关系。     

Fe+注入植物种子射程实验的Monte-Carlo仿真

研究表明,TRIM程序运算结果与实验测量离子注入种子的射程分布数据相差甚远.本文根据种子微结构的特点,综合考虑多种因素,设计种子微结构模型和运算程序,用Monte-Carlo仿真不同能量（110 keV,20 keV,200 keV）、不同注量（2×10¹⁶ ions·cm^-2,5×10¹⁶ ions·cm^-2,10¹⁷ ions·cm^-2,2×10¹⁷ ions·cm^-2）的Fe⁺注入花生、彩棉、小麦种子的射程分布,结果显示本设计程序仿真的结果与实验测量数据较为吻合.所获得的注入离子与种子微结构相互作用的随机抽样模拟运算方法,为离子注入与生命体相互作用的理论研究提供新的思路.     

975 nm量子阱激光二极管的质子位移损伤

针对典型卫星轨道辐射环境下激光二极管(LD)的可靠性评估问题，对自研的975 nm GaAs基量子阱(QW)LD开展了10 MeV质子、3×10⁸～3×10¹¹ cm^-2注量的地面模拟辐照实验。结合蒙特卡罗软件仿真模拟和数学分析方法，全面研究了器件位移损伤退化规律，以及不同注量、不同辐照缺陷对器件功率特性、电压特性和波长特性等关键参数的影响。结果显示，质子辐照会引入非辐射复合中心等缺陷并破坏界面结构，导致载流子浓度降低、光电限制能力下降，宏观上体现为器件阈值电流增加、输出功率下降、波长红移和单色性受损。同时，3×10¹⁰ cm^-2以上注量的10 MeV质子等效位移损伤剂量辐照会对975 nm QW LD性能产生较大影响。     

SiC埋层的制备及其红外吸收特性

采用metal vapor vacuum arc离子源的离子束合成方法，对单晶Si衬底注入C^＋离子，获得不同剂量下的SiC埋层．C^＋离子束的引出电压为50kV，注入的剂量为3.0×10¹⁷—1.6×10¹⁸cm^-2．通过红外吸收谱的测试和分析，表明SiC埋层的结晶程度依赖于剂量的大小．研究证实，可以在较低的平均衬底温度下（低于400℃）得到含立方相结构的SiC埋层． 关键词：     

n型Bi2Te3基化合物的类施主效应和热电性能

晶粒细化是提高Bi₂Te₃基热电材料力学性能的重要方法,但晶粒细化过程中伴随的类施主效应严重劣化了材料的热电性能,并且一旦产生类施主效应,就很难通过简单的热处理等工艺消除.本文系统研究n型Bi₂Te₃基化合物烧结前粉体颗粒尺寸对材料类施主效应和热电性能的影响规律.随着颗粒尺寸减小,氧诱导的类施主效应明显增强,载流子浓度从10 M烧结样品的3.36×10¹⁹ cm^-3急剧增加到120 M烧结样品的7.33×10¹⁹ cm^-3,严重偏离最佳载流子浓度2.51×10¹⁹ cm^-3,热电性能严重劣化.当粉体颗粒尺寸为1—2 mm时,烧结样品的Seebeck系数为–195 μV/K,载流子浓度为3.36×10¹⁹ cm^-3,与区熔样品沿着ab面方向的Seebeck系数为–203 μV/K和载流子浓度为2.51×10¹⁹     

掺Er/Er+O的GaN薄膜光学性质的研究

利用Raman散射谱研究了GaN注Er以及Er+O共注样品的振动模，并讨论了共注入O对Er离子发光的影响. 在Raman散射谱中，对于注Er的GaN样品出现了300 cm^-1和670 cm^-1两个新的Raman峰，而对于Er+O共注样品，除了上述两个峰外，在360 cm^-1处出现了另外一个新的峰，其中300 cm^-1峰可以用disorder-activated Raman scattering (DARS)来解释，670 cm^-1峰是由于与N空位相关的缺陷引起的，而360 cm^-1峰是由O注入引起的缺陷络合物产生的. 由于360 cm^-1模的缺陷出现，从而导致Er+O共注入GaN薄膜红外光致发光(PL)强度的下降. 关键词： GaN Er Raman散射 光致发光     

Ion synthesis of silver nanoparticles in viscous-fluid epoxy resin

A method is described for the ion synthesis of silver nanoparticles in epoxy resin that is in a viscousfluid state (viscosity 30 Pa s) during irradiation. The viscous-fluid or glassy polymer is implanted by 30-keV silver ions at a current density of 4 μA/cm² in the ion beam in the dose range 2.2 × 10¹⁶–7.5 × 10¹⁶ ions/cm². The epoxy layers thus synthesized contain silver nanoparticles, which are studied by transmission electron microscopy and optical absorption spectroscopy. The use of the viscous-fluid state increases the diffusion coefficient of the implanted impurity, which stimulates the nucleation and growth of nanoparticles at low implantation doses and allows a high factor of filling of the polymer with the metal to be achieved.     

Synthesis of Ag metallic nanoparticles by 120 keV Ag− ion implantation in TiO2 matrix

TiO₂ thin film synthesized by the RF sputtering method has been implanted by 120 keV Ag^? ion with different doses (3?×?10¹⁴, 1?×?10¹⁵, 3?×?10¹⁵, 1?×?10¹⁶ and 3?×?10¹⁶ ions/cm²). Further, these were characterized by Rutherford back Scattering, XRD, X-ray photoelectron spectroscopy (XPS), UV–visible and fluorescence spectroscopy. Here we reported that after implantation, localized surface Plasmon resonance has been observed for the fluence 3?×?10¹⁶ ions/cm², which was due to the formation of silver nanoparticles. Ag is in metallic form in the matrix of TiO₂, which is very interestingly as oxidation of Ag was reported after implantation. Also, we have observed the interaction between nanoparticles of Ag and TiO₂, which results in an increasing intensity in lower charge states (Ti³⁺) of Ti. This interaction is supported by XPS and fluorescence spectroscopy, which can help improve photo catalysis and antibacterial properties.     

钴离子注入对二氧化钛晶体的结构和光学性能的影响

采用离子注入法制备了钴离子掺杂的金红石相TiO₂样品;离子注入能量、注量分别为40 keV(1×10¹⁶cm^-2),80 keV(5×10¹⁵,1×10¹⁶,5×10¹⁶,1×10¹⁷cm^-2),120 keV(1×10¹⁶cm^-2). 通过XRD,XPS和UV-Vis等手段对掺杂前后样品的结构和光学性能进行了表征,分析了掺杂元素在金红石TiO₂中的存在形式. XRD测试表明随着注入能量的增加晶体的损伤程度增加. UV-Vis测试表明掺杂后所有样品在可见光区的吸收增强; 并且随着注量的增加,注量为5×10¹⁵cm^-2到5×10¹⁶cm^-2范围内注入样品的光学带隙逐渐变小. 关键词： 钴 二氧化钛 离子注入 掺杂     

离子注入ZnO薄膜的拉曼光谱研究

室温下,用80 keV N⁺和400 keV Xe⁺离子注入ZnO薄膜,注入剂量分别为5.0×10¹⁴—1.0×10¹⁷/cm²和2.0×10¹⁴—5.0×10¹⁵/cm².利用拉曼散射技术对注入前后的ZnO薄膜进行光谱测量和分析,研究了样品的拉曼光谱随离子注入剂量的变化规律.实验结果发现,未进行离子注入的样品在99,435 cm<     

Optical properties of ZnO and Al2O3 implanted with silver ions

ZnO and Al₂O₃ samples implanted with 30-keV silver ions with fluences in the interval (0.25–1.00) × 10¹⁷ ions/cm² are studied by the method of optical photometry in the visible part of the spectrum. The optical transmission spectra of the implanted samples exhibit a selective band associated with surface plasmon resonance absorption of silver nanoparticles. The intensity of this band nonmonotonically depends on the implantation fluence. The silver ion depth distribution in the samples is calculated. It is shown that the non-monotonicity observed in experiments is due to an increase in the substrate sputtering ratio with increasing implantation fluence. It is found that vacuum thermal annealing of the implanted Al₂O₃ layers up to 700°C causes a considerable narrowing of the plasmon absorption bandwidth without a tangible change in its intensity. At higher annealing temperatures, the plasmon absorption band broadens and its intensity drops. Annealing of the ZnO films under such conditions causes their complete vaporization.     

Iron nanoparticles in amorphous SiO<Subscript>2</Subscript>: X-ray emission and absorption spectra

The local structure of the chemical bond of iron ions implanted into SiO₂ glasses (implantation energy, 100 keV; fluence, 1 × 10¹⁶ cm^?2) is investigated using x-ray emission and absorption spectroscopy. The Fe L x-ray emission and absorption spectra are analyzed by comparing them with the corresponding spectra of reference samples. It is established that iron nanoparticles implanted into the SiO₂ vitreous matrix are in an oxidized state. The assumption is made that the most probable mechanism of transformation of iron nanoparticles into an oxidized state during implantation involves the breaking of Si-O-Si bonds with the formation of Si-Si and Fe-O bonds.     

Changes in Structural and Optical Properties of Polycarbonate Induced by Ag+ Ion Implantation

Transparent polycarbonate samples were implanted with 1 MeV Ag⁺ ions to various doses ranging from 5 × 10¹⁴ to 3 × 10¹⁶ ions cm^?2 with a beam current density of 900 nA cm^?2. Modification in the structure of polycarbonate as a function of the implantation fluence was investigated using micro-Raman spectroscopy, glancing angle X-ray diffraction, and UV-Vis spectroscopy. Raman spectroscopy pointed toward the formation of graphite structures/clusters due to the ion implantation. UV-Vis absorption analysis suggests the formation of a carbonaceous layer and a drastic decrease in optical band gap from 4.12 eV to 0.50 eV at an implanted dose of 3 × 10¹⁶ ions cm^?2. The correlation between the decrease in band gap and the structural changes is discussed.     

Interaction of high-power laser pulses with glasses containing implanted metallic nanoparticles

Sodium calcium silicate glasses with Ag⁺ implanted ions are studied. The ion implantation conditions are as follows: the energy is 60 keV, the dose is 7×10¹⁶ cm⁻², and the ion current density is 10 μA/cm². Ion implantation provides the formation of a composite layer that incorporates silver nanoparticles in the surface region of glass. The size distribution of nanoparticles over the depth in the composite layer is strongly nonuniform. The effect of a high-power pulsed excimer laser on the composite layer is investigated. It is found that, under laser irradiation, the size of silver nanoparticles in the implanted layer decreases but the size distribution of nanoparticles over the depth remains nonuniform, even though it becomes slightly narrower compared to that observed prior to irradiation. The experimental results are interpreted in terms of the effects of the melting of glass and metallic particles on a nanosecond scale. __________ Translated from Fizika Tverdogo Tela, Vol. 43, No. 11, 2001, pp. 2100–2106. Original Russian Text Copyright ? 2001 by Stepanov, Popok, Hole, Bukharaev.     

Electrical characteristics of etched ion-tracks in polyimide filled with silver nanoparticles

Silicon ions, of energy 150?MeV and fluence ～10¹²?ions/cm², were used to register latent tracks in 40?µm thick polyimide samples. Different sizes of tracks were obtained by etching the ion irradiated polyimide samples, in chemical solutions, by varying the temperature and etching period. Silver nanoparticles were diffused into the etched tracks by immersing the polyimide samples in silver solution and then irradiating with 6.5?MeV electrons at different fluences varying from 1?×?10¹⁵ to 5?×?10¹⁵?cm^?2. Results of morphological and elemental analysis, carried out by Scanning Electron Microscopy and Energy Dispersive X-ray. Analysis revealed that the conical tracks could be fully filled with silver nanoparticles at electron fluence of 5?×?10¹⁵?cm^?2. The minimum d. c. resistance of an array of tracks, filled with silver nanoparticles and measured across the polyimide film, was orders of magnitude higher as compared to that of silver wires of equivalent sizes connected in parallel. In addition, these silver nanoparticles filled tracks exhibited rectifying I–V behavior and frequency dependent a. c. resistance, characteristic of metal–polymer nano-composites. Possible mechanisms have been discussed, which can justify the asymmetric current–voltage characteristics in such nano-composites.     

Ag-Cu离子注入玻璃后不同气氛退火的光吸收研究

采用MEVVA源（metal vapor vacuum arc ion source）引出的强束流脉冲Ag,Cu离子先后注入到SiO₂玻璃，x射线光电子能谱仪（XPS）分析显示Ag，Cu大多仍为金属态，有部分氧化态Cu存在.透射电镜观察分析和光学吸收谱都表明在衬底中形成了纳米合金颗粒.结合有效媒质理论，得到模拟的光学吸收谱，与实验结果基本符合，较好地验证了以上结论.样品退火后颗粒发生分解，分解的颗粒在氧化气氛下被氧化，且有部分向样品表面蒸发；在还原气氛下氧化态元素被还原并成核生长.故 关键词： 离子注入 纳米颗粒 退火 光学吸收率