淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂的制备

以过硫酸铵为引发剂,N,N-亚甲基双丙烯酰胺为交联剂,淀粉与丙烯酸/醋酸乙烯酯混合单体通过接枝共聚,制备了吸水及耐盐性能均较好的淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂(CGAV)。最佳工艺条件为:淀粉10.0 g,m(混合单体)∶m(淀粉)=4∶1,w(引发剂)=0.3%,w(交联剂)=0.05%,于45℃反应2h~3 h。在最佳工艺条件下制得的CGAV吸去离子水率760 g.g-1,吸0.9%NaC l水溶液率68 g.g-1。     

高取代度羧甲基壳聚糖的制备

用非质子溶剂法,以DMSO-H2O为溶剂,在碱性条件下壳聚糖(CTS)与氯乙酸反应,制得取代度为1.93的羧甲基壳聚糖(CMC)。较适宜的反应条件为:CTS 1 g,m(氯乙酸)∶m(CTS)=5∶1,w(NaOH)=35%(以CTS质量计算),w(十六烷基三甲基溴化铵)=5%(以CTS质量计算),于50℃反应6 h。用XRD和IR对CMC进行表征,结果表明CTS的-OH参与了羧甲基化反应,-NH2没有参与反应。     

泡沫聚合法制备超大多孔水凝胶

采用泡沫体系分散聚合法,过硫酸铵(APS)及N,N,N′,N′-四甲基乙二胺(TMEDA)为氧化还原引发体系,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,碳酸钠为发泡剂,聚氧化乙烯-氧化丙稀(PF127)为泡沫稳定剂,用羧甲基纤维素钠(CMC)接枝丙烯酸(AA)和2-丙烯酰胺基-2-甲基丙磺酸(AMPS)合成了CMC-g-(AA-co-AMPS)超大多孔水凝胶。通过FTIR、SEM表征,表明材料是具有超大多孔结构的CMC-g-(AA-co-AMPS)水凝胶。对各影响因素的研究表明,在m(CMC)∶m(AA)∶m(AMPS)为1∶4∶1,w(APS)为0.8%[其中m(APS)∶m(TMEDA)=2∶1],w(Na2CO3)=65%,w(PF127)=0.2%,温度为65℃时,制得的凝胶吸蒸馏水倍率可达1281g/g,吸0.9%盐水倍率达143g/g,10min时已基本达到溶胀平衡。     

甲基葡萄糖苷硬脂酸酯及其聚氧丙烯醚的合成

以α-甲基葡萄糖苷和硬脂酸甲酯为原料,在碱性催化剂K2CO3和相转移催化剂四丁基氯化铵(TBAC)共同作用下,无溶剂法合成了甲基葡萄糖苷硬脂酸酯(SS),再与环氧丙烷反应,合成了甲基葡萄糖苷硬脂酸酯聚氧丙烯醚(SSP),并对产品进行了IR表征.探讨了相转移催化酯交换反应机理.研究了原料配比、催化剂种类及用量、反应温度、反应时间等因素对SS收率的影响,得到了合成SS的适宜工艺条件:n(甲基葡萄糖苷)∶ n(硬脂酸甲酯)=0.71∶ 1,w(K2CO3)∶ w(硬脂酸酸甲酯)=0.04∶ 1,w(TBAC)∶ w(硬脂酸甲酯)=0.05∶ 1,反应温度145℃,时间4.5h,压力6kPa.上述条件下,SS收率可达92%,产品质量较好.     

4-炔丙氧基苯甲酸的水相合成

以聚乙烯醇(PEG 600)为相转移催化剂,对羟基苯甲酸(2)与3-溴丙炔(3)反应,成功地完成了4-炔丙氧基苯甲酸(其结构经1H NMR和IR表征)的水相合成.最佳反应条件为: 2 0.5 mmol, n(2) ∶ n(3) ∶ n(NaOH)=1.0 ∶ 1.1 ∶ 4.0, w(PEG)=5%,水200 mL,于75 ℃反应72 h,产率85%.     

杂多酸盐催化合成碳酸丙烯酯

以杂多酸盐为催化剂,尿素(1)和1,2-丙二醇(2)为原料合成了碳酸丙烯酯.考察了不同杂多酸盐的催化活性和影响反应的因素.较适宜的反应条件为: 1 500 mmol, n(1) ∶ n(2)=1 ∶ 2, w(钨硅酸锌)=2.0%,于165 ℃反应6 h,收率97.32%.硅钨酸锌重复使用5次后,收率仍高于90%.     

固体超强酸ZrO_2/S2O_8~(2-)催化合成肉桂酸甲酯

研究了在固体超强酸ZrO2/S2O2-8催化下,肉桂酸与甲醇作用合成肉桂酸甲酯的工艺.考查了催化剂的用量、酸醇摩尔比、反应时间及催化剂的性能对反应的影响.最佳反应条件为∶n(肉桂酸)∶n(甲醇)=1∶10,m(肉桂酸)∶m(催化剂)=3∶1,反应温度90～95℃,反应时间5h,酯化率为95.7%.     

相转移催化合成2,6,2'''',6''''-四甲基偶氮苯

以2,6-二甲基苯胺(1)为原料,铁氰化钾和氢氧化钠为缩合剂,采用季铵盐(C8～10H17～21)3N CH3Cl-(A-1)相转移催化合成了2,6,2',6'-四甲基偶氮苯.正交实验确定最佳反应条件为:1 50 mmol,n(铁氰化钾)∶n(1)=5∶1,w(A-1)=5%,于95℃反应15 min,收率45.87%.     

混合钴源对Co-Pd/TiO2催化剂催化CH4-CO2两步梯阶转化法合成乙酸的性能影响

以混合钴源为前驱体, 采用等体积浸渍法制备了Co-Pd/TiO2催化剂, 考察了其对CH4和CO2梯阶转化直接合成乙酸的催化性能, 采用XRD, XPS, NH3-TPD和BET对催化剂进行了表征. 结果表明, 催化剂具有适宜的表面酸性、 高比表面积和孔结构, 有利于提高催化剂的活性. 在m(CoCl2)∶m=2∶5, m(Co)∶m(Pd)=2∶1, 常压, 150 ℃条件下, 乙酸的生成速率达到6.13 mg·g-1Cat·h-1, 选择性达到 81.6%, 分别比以单一Co源制备的催化剂提高了134%和16%.     

氟苯尼考琥珀酸单酯的合成工艺优化

以氟苯尼考和琥珀酸酐为原料,4-二甲氨基吡啶(DMAP)催化合成了氟苯尼考琥珀酸单酯。通过正交试验确定最佳反应条件为:氟苯尼考14 mmol,n(氟苯尼考)∶n(琥珀酸酐)=1.0∶1.5,w(DMAP)=4%,于60℃反应4 h,产率88.1%。在最佳反应条件下做放大实验,氟苯尼考3 kg,产率88.9%     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.