四氯化锡催化合成己二酸二丁酯

应用五水四氯化锡催化己二酸和正丁酯的酯化反应，合成了己二酸二丁酯。研究结果表明，五水四氯化锡具有较高的催化活性。考察了己二酸／正丁醇摩尔比和催化剂用量对酯产率的影响，在适宜反应条件[n(己二酸)：n(正丁醇)：n(四氯化锡)＝1：8：0．114，回流反应60min]下，己二酸二丁酯的产率为96．9％。     

四氯化锡催化合成癸二酸二丁酯

在五水四氯化锡作用下,用癸二酸和正丁醇合成了癸二酸二丁酯。当癸二酸、正丁醇和四氯化锡的物质的量之比为1∶8∶0.114,回流分水60 min,酯收率达96.2%。并比较了几种Lewis酸合成癸二酸二丁酯的催化活性。     

Pd-Sn-K/SiO2催化剂上甲苯气相氧乙酰化反应

 在常规固定床流动反应体系中研究了Pd-Sn-K/SiO2催化剂上气/固相氧化条件下甲苯与乙酸一步合成乙酸苄酯的反应. 结果表明,金属态钯是催化甲苯氧乙酰化合成乙酸苄酯的高活性组分,锡化合物的存在可明显提高催化剂的活性. 催化剂的活性与制备方法密切相关,用H2将SiO2上负载的钯化合物还原之后再负载锡化合物所得催化剂的活性较高. XRD分析结果表明,钯还原前负载锡化合物所得催化剂的活性大幅度降低的原因在于Pd和Sn形成了金属间化合物. 使用Pd/SiO2质量比为0.015, K∶Sn∶Pd摩尔比为27∶3∶1的Pd-Sn-K/SiO2催化剂,在反应温度为180 ℃,混合原料气甲苯∶乙酸∶氧气∶氮气摩尔比为1∶4∶1∶4以及空速为 1680 h-1的条件下,甲苯转化率可达25.3%, 乙酸苄酯选择性为91%. 以TiO2和ZrO2代替SiO2载体,或以其它变价金属氧化物代替Sn氧化物助剂或金属钯,均未发现有更好的催化效果.     

固体酸催化合成马来酸二丁酯

制备了固体酸催化剂Zr(SO4)2/SiO2,并用于合成马来酸二丁酯,考察了Zr(SO4)2负载量、焙烧温度、焙烧时间等催化剂制备条件对催化活性的影响。采用FTIR、XRD、TG等方法对催化剂进行了表征分析。通过正交实验设计优化了固体酸Zr(SO4)2/SiO2催化合成马来酸二丁酯的工艺条件。实验结果表明,Zr(SO4)2/SiO2是合成马来酸二丁酯的良好催化剂,适宜的催化剂制备条件为:硫酸锆负载量57%,焙烧温度400℃,焙烧时间2 h。适宜的催化合成反应条件为:酐醇物质的量比为1∶2.5,催化剂用量为马来酸酐质量的6%,带水剂甲苯8 mL,反应时间2.0 h。在此条件下马来酸二丁酯的酯化率为98.5%。     

强酸性阳离子交换树脂催化合成丁二酸二丁酯

用强酸性阳离子交换树脂催化丁二酸和正丁醇的酯化反应,合成了丁二酸二丁酯。研究了影响反应的因素和催化剂的重复使用性能,在丁二酸25mmol,正丁醇200mmol和催化剂1．5g,回流分水120min的反应条件下,酯化率达95．7％。催化剂套用5次,其活性未发生明显变化。     

金催化顺丁烯二酸酐的选择加氢反应

采用溶胶-凝胶法制备了一系列担载纳米金催化剂,用以催化顺丁烯二酸酐(简称顺酐,MA)的选择加氢反应．模板剂的引入改变了催化剂载体的结构,从而提高了其催化活性和对加氢产物丁二酸酐(SA)以及丁二酸二乙酯(DFAS)的选择性．同时考察了反应温度、溶剂、催化剂制备方法对顺酐选择加氢反应的影响以及催化剂的重复使用性能．实验结果表明,以焙烧处理除去模板剂十八胺的Au／SiO2-O(C)为催化剂时,顺酐选择加氢制取丁二酸酐和一步加氢酯化制取丁二酸二乙酯的效果最佳,其转化率以及产物选择性均大于99．5％．     

Ni/SiO_2、Ni/TiO_2-SiO_2催化剂上顺酐液相选择加氢合成γ-丁内酯

通过溶胶-凝胶方法结合超临界干燥技术制备了SiO2和TiO2-SiO2复合氧化物气凝胶载体,采用等体积浸渍法制备了Ni/SiO2和Ni/TiO2-SiO2催化剂,运用BET、H2-TPR、XRD、TEM及FT-IR等手段对催化剂进行了表征,并考察了催化剂在顺酐液相选择加氢合成γ-丁内酯反应中的催化性能.结果表明,Ni/TiO2-SiO2催化剂中Ti-O-Si键的形成增强了NiO与载体的相互作用,促进了NiO在载体表面的分散,得到了晶粒较小的活性Ni0物种,表现出高的加氢活性,在H2压力5.0 MPa、反应温度240℃、反应时间6 h的条件下,顺酐转化率为100%,γ-丁内酯的选择性达94.7%.     

乳酸丁酯的非均相催化合成

在Ga2 O3负载量为20％,500℃焙烧2h的条件下制备了固体酸催化剂Ga2 O3/SiO2,利用红外光谱分析对催化剂进行了表征.将其用于非均相催化合成乳酸丁酯的反应,考察了催化剂用量、n(正丁醇)∶n(乳酸)、环己烷用量、反应时间和催化剂重复使用性能等因素对酯化率的影响.结果表明,该催化剂催化合成乳酸丁酯的适宜反应...     

磷钨酸催化合成癸二酸二丁酯

用磷钨酸催化合成癸二酸二丁酯，考察了诸因素对酯化率的影响，产品经IR鉴定。确定酯化反应的最佳条件为：癸二酸50mmol，n(癸二酸)：n(正丁醇)=l：4，催化剂0．5g(反应物总质量的1．7％)，反应时间2h，酯化率达96．46％。     

微波协同离子液体催化合成马来酸二丁酯

以马来酸酐和正丁醇为原料,用微波协同离子液体[HSO3-pmim]+[HSO4]-催化合成了马来酸二丁酯。通过单因素实验和正交试验考察催化剂种类、催化剂用量、马来酸酐与正丁醇物质的量比、微波功率、微波时间对马来酸二丁酯产率的影响。实验结果表明,马来酸二丁酯最佳合成条件为:马来酸酐与正丁醇物质的量比1∶4,以离子液体[HSO3-pmim]+[HSO4]-为催化剂,其用量为2.0g,微波功率为600W,微波时间为15min,马来酸二丁酯产率可达到99.36%。在微波辐射下,催化剂离子液体[HSO3-pmim]+[HSO4]-重复使用7次后活性没有明显降低,马来酸二丁酯产率仍高于96%,表明该催化剂具有较好的反应活性和稳定性。与常规加热方式相比,微波加热提高了反应效率,缩短了反应时间。     

丁烯二酸二丁酯配体异构化的研究

用市售的未经分离提纯的顺丁烯二酸二丁酯与W(CO)4(phen)(phen=1,10-邻菲咯啉)在甲苯中加热回流24h,反应液经硅胶柱层析分离得到两个产物,分别用甲苯/石油醚重结晶,获得橙黄色块状晶体(1)和橙红色片状晶体(2)。用X射线衍射法测定其晶体结构分别为W(CO)2(phen)(DBF)2(1)与W(CO)2(phen)(DBF)(DBM)(2)(DBM=顺丁烯二酸二丁酯,DBF=反丁烯二酸二丁酸)。经对原料中的DBM和DBF含量的分析及对两种产物中DBF总量的计算表明配体DBM很可能在配位反应过程中有部分异构化为更稳定的配体DBF.     

硅胶负载H6PMo9V3O40催化合成5-硝基水杨醛

采用硅胶负载Keggin型H6PMo9V3O40催化水杨醛与硝酸反应合成5-硝基水杨醛,考察了催化剂负载量、反应时间、反应温度、催化剂用量、硝酸用量和溶剂对反应的影响及催化剂的重复使用性能。实验结果表明,m(水杨醛)∶m(质量分数65%硝酸)∶m(负载量20%H6PMo9V3O40/SiO2)=2.44∶3.00∶3.00,用石油醚作为溶剂,45℃反应2.5 h,水杨醛的转化率为98%,5-硝基水杨醛的选择性为96.8%。催化剂回收容易,重复使用5次后,活性基本不变。     

Colloidal aggregation phenomena: Spatial structuring of TEOS-derived silica aerogels

In this contribution, the homogeneity of silica aerogels made from tetraethyl orthosilicate (TEOS) was studied by means of Fourier transform infrared (FTIR) and 29Si nuclear magnetic resonance (NMR) spectroscopies. FTIR spectra show a slight difference in the asymmetric Si-O-Si stretching vibration frequency in the outer and inner part of the aerogels. According to the 29Si NMR data, a higher relation Q4/Q3 was obtained in the inner parts of the gels compared with their outer parts, proving the difference in the cross linkage of the silica network. The obtained results are interpreted in terms of the specific spatial structuring of the colloidal suspensions due to the presence of gravity.     

YAl3（BO3）4∶Eu3+荧光粉的化学沉淀法制备研究

以化学沉淀法制备单相的铕离子掺杂硼铝酸盐红色荧光粉YAl3(BO3)4∶Eu3+,考察了焙烧温度、掺铕量等因素对材料性能的影响,用X射线衍射、扫描电镜、激发光谱和发射光谱对荧光粉的结构、形貌和发光性能进行了表征.以尿素为沉淀剂,900℃焙烧沉淀前驱体可得到单相荧光粉YAl3(BO3)4∶Eu3+,反应温度比传统高温固相法降低了300℃;沉淀法制备的荧光粉粒径分布范围小,无团聚现象,粒径约300nm.掺铕量为10%(物质的量比)时发光强度最大.在260nm的紫外光激发下,Eu3+的5 D0→7 F2的电偶极跃迁最强,发射光为618nm的红光.     

TiO2柱层状HTiNbO5的合成及在环己酮肟气相Beckmann重排反应中的催化性能

钛酸异丙酯(TIP)、CH₃COOH和H₂O按体积比1∶16∶40混合后得到Ti(Ⅳ)多聚阳离子柱化液, 与正癸胺插层钛铌酸盐进行交换反应后制得钛(Ⅳ)多聚阳离子插层钛铌酸盐, 其层间距为1.70 nm. 在空气气氛中于623 K焙烧处理后, 所得产品能保持良好的层柱结构. 在空气气氛中于723 K焙烧后所得的TiO₂柱层状钛铌酸(TiO₂-HTiNbO₅), 其层间距为0.97 nm, 比表面积为89 m²/g. 以TiO₂-HTiNbO₅为载体, 用浸渍法制备了一系列B₂O₃负载量不同的负载型样品B₂O₃/TiO₂-HTiNbO₅, 考察了它们在环己酮肟气相Beckmann重排反应中的催化性能并测试了它们的红外光谱. B₂O₃/TiO₂-HTiNbO₅的催化性能优于TiO₂-HTiNbO₅. 在B₂O₃负载质量分数为7.31%的催化剂上, 环己酮肟转化率接近100%且在4.5 h内无明显改变, 己内酰胺选择性接近90%. 红外光谱分析结果表明, 当B₂O₃负载量很低时, 硼组分高度分散于载体TiO₂-HTiNbO₅表面, 并主要以BO₄结构形式存在; 当B₂O₃负载质量分数高于7.31%时, BO₃结构形式在数量上占优势. 将催化性能与红外光谱结果关联后可知, 对于负载型样品B₂O₃/TiO₂-HTiNbO₅, 表面的BO₃和BO₄两种结构形式在环己酮肟气相Beckmann重排反应中具有协同促进作用.     

The Dehydrogenation of Propane on Platinum–Tin Glass-Fiber Woven Catalysts

The reaction of propane dehydrogenation on platinum–tin catalysts supported onto different woven carriers (an aluminoborosilicate and two silica materials) was studied. It was found that the catalyst was rapidly deactivated by carbon deposits formed, and the rate of this reaction increased with the specific surface area of the glass-fiber woven material and the Pt content. It was established that the Pt: Sn ratio in surface platinum particles was about 6, and it increased to 39 after the reaction; this fact is indicative of a Sn loss, which led to an increase in the conversion of feed into carbon deposits that deactivated the catalyst. A mixture of propane and 5–10 vol % H₂ should be used for the stabilization of the catalytic system; in this case, the negative effect of hydrogen on the yield of propylene was minimal. On the catalyst supported onto a silica carrier under optimum conditions (550°C; propane space velocity, 480 h^–1), which correspond to minimum selectivity for the formation of carbon deposits, the yield of propylene was ~18%. The test glass-fiber woven catalyst was inferior to granulated platinum–tin catalysts in terms of catalytic activity; therefore, its use in the reaction of propane dehydrogenation is inexpedient.     

Controlled Preparation of Hydrangea-like 0.3Zn-0.15Sn/CuO Catalysts for the Rochow-Müller Reaction by Microwave-Assisted Liquid-Phase Synergistic Impregnation

In catalytic reactions, trace amounts of promoters can make up for the low activity of a catalyst and significantly affect the physicochemical properties of the catalyst. Exploring a simple and efficient composite Cu-based catalyst is essential to the Rochow-Müller reaction. In this work, monodisperse, a hydrangea-like 0.3Zn-0.15Sn/CuO composite catalyst in the Rochow-Müller reaction. The composite was synthesized via a microwave-assisted liquid-phase synergistic impregnation method in which Sn and Zn were used to dope the CuO surface to create strong Si interaction points. A significant increase in the catalytic activity of CuO was observed after Sn and Zn doping, attributed to the rearrangement of charges on the CuO surface and increase in the Cu atom's core electron density. This work provided a novel and efficient method for preparing efficient Cu-based catalysts for the Rochow-Müller reaction.     

Porous texture of silica aerogels made with ionic liquids as gelation catalysts

The effect of four ionic liquids on the porous texture of silica aerogels synthesized from mixed tetramethoxysilane and methyltrimethoxysilane and dried by the CO₂ supercritical method, was studied. Two of these ionic liquids were composed of BF₄ ⁻ anions while the other two included Cl⁻ anions. The synthesis of gels from ionic liquids did not require another acidic catalyst for silica hydrolysis, nor a basic catalyst for silica condensation. These aerogels were compared with traditional aerogels made according to a double step catalysis, which first involved hydrolysis with HCl followed by condensation with pH 9 Tris HCl buffer. Gel mass analysis and thermogravimetric data showed that, when the initial molar of ionic liquid to Si was 1.58, only ~2% (by mass) of the initial ionic liquids consisting of BF₄ ⁻ anions and ~10% (by mass) of ionic liquids containing Cl⁻ anions, remained in the aerogels after supercritical drying. Moreover, X-ray diffraction confirmed that in ionic liquids based on BF₄ ⁻ anions, evaporation of the volatile components before supercritical CO₂ drying led to the formation of regularly ordered mesopores.     

温控Noyori配体的合成及在苯乙酮不对称氢转移反应中的应用

设计并合成了一种新型的聚乙二醇单甲醚(MPEG)修饰的温控Noyori配体.将其与[RuCl2.(p-cymene)]2络合形成的催化剂用于水/环己烷两相体系中苯乙酮不对称氢转移反应.以甲酸钠为氢源,考察了反应温度、时间、甲酸钠用量、底物与催化剂摩尔比以及溶剂用量等因素对催化反应的影响.结果表明,反应体系中含催化剂的水相具有浊点,并且催化剂显示出良好的不对称催化性能,在甲酸钠/苯乙酮/催化剂的摩尔比为300:100:1、环己烷/水体积比1:1及30℃的反应条件下反应6h,苯乙酮的转化率为99.7%,产物α-苯乙醇的对映选择性(e.e.)为93.9%.催化剂相易与产物相分离并与直接循环使用,循环使用的催化剂活性明显下降,但产物对映选择性仍保持不变.     

Low thermalconductive,transparent and hydrophobic ambient pressure dried silica aerogels with various preparation conditions using sodium silicate solutions

The experimental results on the preparation of low thermal conductivity and transparent ambient pressure dried silica aerogels with the sodium silicate solution, TMCS silylating agent with methanol, isopropyl alcohol, hexane and xylene solvents, are reported. This study is focussed on the effect of preparation conditions such as varying the number of preparation steps, pH of the hydrosol and hydrogel ageing temperature, for the production of the low thermal conductive silica aerogels and the results are analysed. Density, thermal conductivity, % of optical transmission and contact angle of the aerogels were measured. The Fourier Transform Infrared Spectroscopy (FTIR) studies revealed the presence of Si–C and C–H along with the Si–O–Si and OH bonds and their intensities strongly depend on the processing steps, pH of the hydrosol and gel ageing temperature. The UV–Visible spectra indicated the % of optical transmission of the aerogels decreased with increasing the number of processing steps, increase in the pH of the hydrosol from 3 to 8 and decreased for ageing temperature up to 50 °C. Further increase in temperature >50 °C, the % of optical transmission of the aerogels increased. The TGA-DTA data showed the thermal stability of the aerogels with respect to hydrophobicity is 325 °C. Transmission Electron Microscopy (TEM) and Scanning Electron Microscopy (SEM) analyses revealed the nanostructure of the aerogels. The porosity of the aerogels was studied using the pore size distribution. Silica aerogels with low density (0.051 g/cc), low thermal conductivity (0.049 W/m K), optical transmission (65%), high hydrophobicity (159°) and resistance to humid atmosphere >1 year was obtained in the present studies.