3-氨基-1,2,4-三氮唑自组装膜对黄铜的缓蚀作用

3-氨基-1,2,4-三氮唑(ATA)是一种环境友好型金属处理剂, 以其在黄铜表面制备了自组装单分子膜(SAMs), 用电化学方法研究ATA SAMs对黄铜的缓蚀作用及其吸附行为. 结果表明, ATA分子易在黄铜表面形成稳定的ATA SAMs, SAMs抑制了黄铜的阳极氧化过程, 改变了电极表面的双电层结构, 固/液界面双电层电容明显降低, 有良好的缓蚀效果. 研究结果还表明, ATA的吸附行为符合Langmuir吸附等温式, 吸附机理是典型的化学吸附.     

绿色聚天冬氨酸复配缓蚀剂对A3碳钢的缓蚀抑雾作用

采用失重法和极化曲线法研究了聚天冬氨酸(PASP)和十二烷基酚聚氧乙烯醚(OP-10)复配对A3碳钢在6mol·L-1HCl腐蚀介质中的协同吸附行为及缓蚀抑雾作用.结果表明:复配缓蚀剂可有效抑制A3碳钢在HC1介质中的腐蚀,当PASP浓度为20g·L-1,缓蚀率可达94%,抑雾率83%;随着温度的升高,复配缓蚀剂的缓蚀性能下降.复合缓蚀剂在钢表面的吸附符合校正的Langmuir模型,吸附过程为放热、熵减的自发过程;复配体系属于阳极型缓蚀剂.     

3-氨基-1,2,4-三氮唑对铜的缓蚀性能和吸附行为

采用电化学和表面增强拉曼光谱(SERS)方法研究了新型环境友好型金属水处理剂3-氨基-1,2,4-三氮唑(ATA)对铜在3% NaCl溶液中的缓蚀性能和吸附行为. 结果表明, ATA对铜有较好的缓蚀作用, 其中ATA浓度为0.24 mmol·L-1时对铜的缓蚀效率最高, 为97.65%, 其吸附行为符合Langmuir吸附等温式, 吸附机理是典型的化学吸附援SERS表明, ATA分子通过很强的吸附于铜表面达到抑制其腐蚀的作用, 是ATA-与Cu+形成配合物来阻止氯离子化合物(CuCl-2)的生成.     

十二烷基苯磺酸钠在AZ31镁合金表面的吸附及其缓蚀作用

采用电化学阻抗谱(EIS)和极化曲线研究十二烷基苯磺酸钠(SDBS)对AZ31镁合金在3.5%(w, 质量分数)NaCl腐蚀介质中的吸附行为及缓蚀作用. 结果表明: SDBS可有效抑制AZ31镁合金在NaCl介质中的腐蚀, 其浓度为0.008 mol·L-1时缓蚀效率可达90%以上; 升高温度并不利于提高SDBS的缓蚀效率. SDBS在AZ31镁合金表面主要发生物理吸附, 吸附过程为放热、熵增的自发过程, 近似符合Langmuir单分子层吸附模型; SDBS为混合抑制型缓蚀剂, 但主要抑制阳极反应.     

咪唑离子液体对铜在硫酸溶液中的缓蚀作用

采用动电位极化和电化学阻抗谱技术研究了三种新型烷基咪唑离子液体, 1-丁基-3-甲基咪唑硫酸氢盐([BMIM]HSO₄), 1-已基-3-甲基咪唑硫酸氢盐([HMIM]HSO₄), 1-辛基-3-甲基咪唑硫酸氢盐([OMIM]HSO₄), 对铜在0.5 mol·L_-1 H₂SO₄溶液中的缓蚀作用. 实验结果表明: 咪唑离子液体能有效抑制铜在硫酸溶液中的腐蚀, 相同浓度下的缓蚀效率大小顺序为[OMIM]HSO₄>[HMIM]HSO₄>[BMIM]HSO₄. 动电位极化表明三种咪唑化合物的加入对铜的阴阳极腐蚀过程均有抑制作用, 属于混合型缓蚀剂. 电化学阻抗谱用带两个常相位原件的等效电路对含两个时间常数的体系进行拟合, 发现咪唑化合物的添加会引起电荷传递电阻和双电层电容等阻抗参数的变化, 表明此类化合物通过吸附于铜电极与溶液界面起到缓蚀作用, 且这种吸附符合Langmuir吸附等温关系. 吸附过程热力学计算说明咪唑化合物在铜表面发生了自发的物理吸附.     

硫酸溶液中Pt电极表面过程的EQCM研究

应用电化学循环伏安和石英晶体微天平(EQCM)方法研究了0.1mol·L-1硫酸溶液中Pt电极表面的吸附和氧化过程.从电极表面质量变化的结果分析,可认为正向电位扫描时氢区表面质量的增加是由于水分子取代Had引起的,而双电层区的质量增加则是由于水的吸附模式逐渐由氢端吸附转向氧端吸附所致.根据频率变化和电量数据,进一步推算出水在双电层区是以低放电吸附形式出现的,1molPt原子和水分子只发生0.054mol的电荷转移.本文结果可为认识Pt电极表面过程提供定量的新数据.     

二硫代酰胺类化合物在盐酸中对碳钢的缓蚀性能(英文)

采用失重实验,动电位极化,交流阻抗,量子化学计算和拉曼光谱等方法研究了N,N′-二异丙氧基丙基二硫代二丙酰胺(DPDA)在1 mol.L-1盐酸溶液中对碳钢的缓蚀性能.失重实验结果表明,DPDA在盐酸溶液中能够有效地抑制碳钢的腐蚀,当缓蚀剂DPDA的浓度为1×10-3 mol.L-1时,其缓蚀效率达到90.2%.极化曲线表明DPDA为混合型缓蚀剂,单一的容抗弧变化表明碳钢电极表面的腐蚀过程主要由电荷转移步骤控制.由失重实验,动电位极化和电化学交流阻抗方法得到的DPDA缓蚀效率具有较好的相关性,均表现为缓蚀效率随着DPDA浓度的增大而增加.另外,DPDA在碳钢表面的吸附符合Langmuir吸附等温式.吸附过程的吉布斯自由能(ΔG0a0d0s)为-38.65 kJ.mol-1,这说明DPDA分子在碳钢表面形成共价键而发生了自发的化学吸附.拉曼光谱表明DPDA分子有效地吸附在碳钢表面,量子化学计算结果证明DPDA分子在碳钢表面的化学吸附活性中心集中在S原子上.     

新型不对称双季铵盐缓蚀剂在HCl中对Q235钢的缓蚀行为

采用静态失重法、极化曲线法和交流阻抗法研究了自制的含咪唑啉环不对称双季铵盐缓蚀剂(DBA)在1 mol•L^－1 HCl介质中对Q235钢的缓蚀性能, 并探讨了其在Q235钢表面的吸附行为. 结果表明, 缓蚀效率随DBA浓度增加而增大, 在25～55 ℃的实验温度范围内, 浓度为2.89×10^－4 mol•L^－1时, 缓蚀效率均在90%以上, 且缓蚀效率随温度升高而增大. 极化曲线测试显示DBA是一种阴极抑制为主的混合型缓蚀剂. 缓蚀剂在Q235钢表面的吸附过程为吸热过程, 其在Q235钢表面的吸附遵循Langmuir等温式, 属于化学吸附. 最后采用量子化学方法对DBA的缓蚀机理做了进一步分析.     

绿色缓蚀剂聚天冬氨酸对铜的缓蚀性能与吸附行为

采用电化学阻抗和极化曲线法研究了绿色缓蚀剂聚天冬氨酸(PASP)对铜在200 mg·L-1的NaCl溶液中的缓蚀性能和吸附行为. 结果表明, 在20 ℃时, PASP使用的最佳浓度为15 mg·L-1, 缓蚀率可达到78.3%, PASP的吸附明显降低了Cl-的侵蚀, 属于阳极型缓蚀剂. 随着温度的升高, PASP的缓蚀性能下降. 在50 ℃时, PASP的缓蚀率下降至40.4%. PASP的吸附行为服从Langmuir吸附等温式,是自发的、放热的过程, 属于化学吸附.     

五种氨基酸在HCl溶液中对铜的缓蚀作用

采用失重法、动电位极化曲线和电化学阻抗谱等方法,分别研究了1mmol/L L-蛋氨酸、L-半胱氨酸、L-精氨酸、L-赖氨酸和L-丙氨酸在0.5mol/L HCl溶液中对铜的缓蚀作用。实验结果表明,5种氨基酸均为阴极型缓蚀剂,其中L-赖氨酸缓蚀效果最好,缓蚀效率可达84.77%,同时也说明L-赖氨酸结构中游离的双氨基对于铜的缓蚀具有一定作用。     

MMI作为铜的盐酸酸洗缓蚀剂作用机理的研究

用失重法研究了N-甲基-2-巯基咪唑（MMI）在5％盐酸中对铜的酸洗缓蚀性能.探讨了温度和MMI浓度对缓蚀效果的影响，从中得出了MMI在铜表面的吸附等温式，计算了吸附热及MMI的加入对铜在盐酸中腐蚀反应活化能的影响，进而探讨了MMI对铜缓蚀作用的机理.结果表明， 30 ℃下，在5％盐酸中，当MMI的浓度在3 mmol•L－1和8 mmol•L－1之间时,缓蚀率随MMI浓度的增加而迅速增加，当浓度达到8 mmol•L－1时，缓蚀率趋于定值，而当浓度小于3 mmol•L－1时， MMI的加入会加速铜的腐蚀；吸附在铜表面的MMI分子间的作用力整体表现为引力； MMI在铜表面的吸附是吸热反应； MMI的加入降低了铜的腐蚀反应活化能.     

Structural effects on the barrier properties of self-assembled monolayers formed from long-chain omega-alkoxy-n-alkanethiols on copper

The adsorption of long-chain omega-alkoxy-n-alkanethiols [CH(3)(CH(2))(p-1)O(CH(2))(m)SH; m = 11, 19, 22; p = 18, 22] onto copper produces self-assembled monolayers (SAMs) that can provide protection against corrosion of the underlying metal substrate. The resulting films are 40-60 A in thickness and are isostructural with SAMs formed on copper from unsubstituted n-alkanethiols. As evidenced by electrochemical impedance spectroscopy (EIS), the barrier properties of these ether-containing SAMs depend on the chain length of the adsorbate and the position of the ethereal unit along the hydrocarbon chain. For SAMs where the ether substitution is farther from the copper surface, the initial coating resistances are similar to those projected for unsubstituted n-alkanethiolate SAMs of similar thickness. For SAMs where the ether substitution is nearer to the copper surface (m = 11), the resistances are significantly less than those for unsubstituted n-alkanethiolate SAMs of similar thickness, reflecting the effect of the molecular structure on the barrier properties of the film. Upon exposure to 1 atm of O(2) at 100% RH, the SAMs become less densely packed as observed by infrared (IR) spectroscopy, and their barrier properties deteriorate as observed by EIS. The rate that the SAMs lose their barrier properties upon exposure to oxidizing conditions is correlated to the strength of intermolecular interactions within the bulk state of the adsorbate.     

An investigation of carbon steel corrosion inhibition in hydrochloric acid medium by an environmentally friendly green inhibitor

The inhibition effect of polyphenols extracted from olive mill wastewater (PP) on carbon steel in 1.0 M HCl solution was studied. Inhibition efficiency of PP was carried out by using chemical (weight loss method) and electrochemical techniques [potentiodynamic polarization and electrochemical impedance spectroscopy (EIS)]. The effect of temperature and immersion time on the corrosion behavior of carbon steel in 1.0 M HCl with addition of an extract was also studied. The results show that PP acts as a very good inhibitor, and the inhibition efficiency increases with the concentration of PP and decreases with rising temperature. Polarization curves show that PP behaves as a mixed-type inhibitor in hydrochloric acid. Data, obtained from EIS measurements, were analyzed to model the corrosion inhibition process through an appropriate equivalent circuit model; a constant phase element has been used. EIS shows that charge-transfer resistance increases and the capacitance of double layer decreases with the inhibitor concentration, confirming the adsorption process mechanism. The activation energy as well as other thermodynamic parameters for the inhibition process were calculated. The adsorption of PP obeys the Langmuir adsorption isotherm.     

Inhibition of copper corrosion by self-assembled monolayers of triazole derivative in chloride-containing solution

The self-assembled monolayers (SAMs) derived from 3-undecane-4-amino-5-mercapto-1,2,4-triazole (UAMT) on copper surface have been characterized by contact angle test, X-ray photoelectron spectroscopy, and electrochemical techniques. It is found that the UAMT molecules can spontaneously adsorb to copper surface to form compact and oriented monolayers, which can prevent the corrosion of copper in chloride-containing solution effectively. The electrochemical measurements prove that the adsorption of UAMT molecules on copper surface typically processes with a two-step adsorption consisting of a fast initial adsorption and a slowly following reorganization in 10^?4-M UAMT solution, and the adsorption of UAMT obeys the Langmuir model in the initial adsorption process. Furthermore, the effects of the immersion time, ultrasonic irradiation, and UAMT concentration on the anticorrosion property of SAMs are studied, and the adsorption isotherm of UAMT on copper is followed.     

Thermodynamic and adsorption behavior of N<Subscript>2</Subscript>O<Subscript>4</Subscript> schiff base as a corrosion inhibitor for API-5L-X65 steel in HCl solution

The inhibition ability of N,N′-bis(2,4-dihydroxyacetophenone)-1,3-propandiimine (DHAPP) as a schiff base against the corrosion of API-5L-X65 in 1 M HCl solution was evaluated by polarization, electrochemical impedance spectroscopy, and scanning electron microscopy. Polarization studies indicated that DHAPP retards both the cathodic and anodic reactions through chemical adsorption and blocking the active corrosion sites. The adsorption of this compound obeyed the Langmuir adsorption isotherm. The inhibition efficiency increased with inhibitor concentration and decreased with increasing temperature. EIS data analysed to equivalent circuit model showed that as the inhibitor concentration increased the charge transfer resistance of steel increased whilst double layer capacitance decreased. Kinetic and thermodynamic parameters such as activation energy, enthalpy, entropy, and Gibbs free energy of activation and adsorption were calculated. Gibbs free energy indicated that adsorption occurred through physical and spontaneous process. Scanning electron microscopy was used to study the steel surface with and without inhibitor.     

柠檬酸中锌防蚀剂（1,3-Dioxolan-2-ylmethyl）三苯基溴化磷和碘离子的协同效应研究

采用称重法、动电位极化法和电化学交流阻抗技术研究了30 ^oC时(1,3-Dioxolan-2-ylmethyl)三苯基溴化磷（DTPB）对0.5 mol·L^-1柠檬酸中锌腐蚀行为的影响. 通过在环保型电解槽中对锌进行酸洗,这在文献中是不常用的. 结果表明,DTPB作为一种有效的防蚀剂,添加浓度仅为3×10^-3 mol·L^-1时,锌在柠檬酸溶液中的防蚀效率可达98.9%. 由于DTPB和碘化钾存在协同效应,两者联用时的防蚀效果要比单独使用DTPB强,防蚀参数为1.2,并随温度升高而减小. 本文提出了碘化钾作为吸附媒介,可使金属表面与DTPB结合的防蚀机制.     

酸性介质中羧甲基纤维素钠在低碳钢表面的吸附和缓蚀作用

The effect of sodiumcarboxymethyl cellulose (Na-CMC) on the corrosion behavior of mild steel in 1.0 mol·L-1 HCl solution has been investigated by using weight loss (WL) measurement, potentiodynamic polarization, linear polarization resistance (LPR), and electrochemical impedance spectroscopy (EIS) methods. These results showed that the inhibition efficiency of Na-CMC increased with increasing the inhibitor concentration. Potentiodynamic polarization studies revealed that the Na-CMC was a mixed type inhibitor in 1.0 mol·L-1 HCl. The adsorption of the inhibitor on mild steel surface has been found to obey the Langmuir isotherm. The effect of temperature on the corrosion behavior of mild steel in 1.0 mol·L -1 HCl with addition of 0.04% of Na-CMC has been studied in the temperature range of 298-328 K. The associated apparent activation energy (E*a) of corrosion reaction has been determined. Scanning electron microscopy (SEM) has been applied to investigate the surface morphology of mild steel in the absence and presence of the inhibitor molecules.