HIPS／SBS共混物的形态结构和性能

通常,高抗冲聚苯乙烯(HIPS)为多相体系,由连续聚苯乙烯(PS)相和分散的聚丁二烯(PB)颗粒组成。PB含量一般为5～15%,粒径范围为0.5～10μm,PB颗粒是交联的,同时含有接枝的PS,其内部结构由制备工艺决定。HIPS力学性能与其制备工艺、PB含量、PB分子结构、相区尺寸及内部结构密切相关。PS和PB嵌段共聚物(SBS)通常为热塑弹性体,由于PS段和PB段的不相容性而呈现微相分离的结构特征。SBS常用于与其它聚合物共混以增加后者的韧性。本工作研究了HIPS/SBS共混物的形态结构和力学性能。     

线形苯乙烯-丁二烯-苯乙烯嵌段共聚物(SBS)的粘弹弛豫与相形态

研究了不同温度下苯乙烯-丁二烯-苯乙烯嵌段共聚物(SBS)的粘弹弛豫与相形态. DSC分析发现, SBS的相结构特别是其中质量分数较低的PS相畴的大小受热历史影响显著. 用TEM表征了SBS的双相连续形态和两相相畴尺寸. 用动态流变学方法研究了不同温度下SBS嵌段大分子的松弛行为. 结果表明, 在低于PS相玻璃化转变温度时, 嵌段分子中的PB段已可发生运动; 而当高于PS玻璃化转变温度后, 由于PB与PS间的相互作用及PB的链缠结所限制, 体系仍保持较高的弹性模量, 呈现“第二平台”特征流变行为.     

聚苯乙烯/聚二甲基硅氧烷嵌段共聚物的表面形态研究

采用原子力显微镜(AFM)和透射电镜(TEM)研究了聚苯乙烯/聚二甲基硅氧烷嵌段共聚物(PS-b-PDMS)薄膜的相形态.结果表明,当采用甲苯作为溶剂,旋转涂膜的薄膜样品呈现网络状的形态分布在表面,而样品所对应的透射电镜照片中,PDMS相作为球状分布在PS的连续相中.退火温度对共聚物表面形态有一定的影响,当退火温度高于PDMS的玻璃化温度,表面中PDMS相增多.PS-b-PDMS嵌段共聚物的表面形态随着所用溶剂的变化而有所不同,当采用甲苯作为溶剂时,样品的PS相形成凹坑分布在PDMS的相区之中,而采用环己烷作为溶剂时,PS相作为突起分布在PDMS相区之中.另外,基底对共聚物薄膜表面形态的有较大的影响,当采用硅晶片作为基底时,样品中的PDMS相和PS相呈现近似平行于表面的层状结构.     

用SAXS/WAXS研究聚氧乙烯/聚氧丁烯嵌段共聚物在n-己烷中的结晶性球形胶束结构

嵌段共聚物在选择性溶剂中能够自组装形成胶束,胶束的不同形状与嵌段共聚物的结构、溶剂和浓度有关．无定形嵌段共聚物通常形成球形胶束,在某些情况下也可以形成其它形状的胶束,关于结晶性嵌段共聚物在无定形链段选择性溶剂中的胶束结构和形状的报道非常少．由于结晶和相似相溶两种作用力的竞争,使得这类胶束的形状丰富多变．通常结晶作用较强时,结晶性嵌段共聚物形成片状的胶束,当结晶组分比较少时,可形成棒状胶束,尽管理论上已经指出存在球形胶束,但尚无关于这方面的报道。     

三嵌段共聚物在气-液界面的有序组装

将氢化的苯乙烯(PS)/丁二烯(PB)/苯乙烯(PS)三嵌段共聚物(SEBS)磺化,得到磺化的SEBS(S－SEBS),在水亚相上铺展了S－SEBS的Langmuir膜,研究其π－A特性.制备S－SEBS的Langmuir－Blodgett(LB)膜,用原子力显微镜(AFM)对其表面形态进行了研究,并以芘作为荧光探针研究了溶液和膜中S－SEBS聚集态的变化.研究结果表明,S－SEBS在气－液界面可以形成由两亲性的纳米小球组装而成的有序的二维和三维的纳米结构.对纳米结构形成的机理进行了初步分析.     

不同极性微量选择性溶剂对聚合物膜表面浸润性的控制

通过在双亲性三嵌段共聚物( PEO-PDMS-PEO)的溶液中加入不同极性的微量选择性溶剂, 分别制得胶束和反胶束微粒, 不同组分的溶液涂膜后显示出明显的浸润性差异. 采用透射电镜、原子力显微镜和X射线光电子能谱分别对胶束和反胶束微粒在溶液中和成膜后的结构以及表面化学组成进行了表征, 结果表明, 不同选择性溶剂所形成的胶束和反胶束微粒的结构差异, 导致了涂膜的表面化学组成的不同, 最终影响其表面浸润性.     

嵌段共聚物胶束薄膜空穴化结构形成的研究

用原子力显微镜研究了嵌段共聚物胶束薄膜的空穴化结构.结果表明,嵌段共聚物胶束薄膜的空穴化强烈地依赖于所用酸中氢离子的数目,只有使用一元酸时才能得到空穴化结构,而二元酸和三元酸都得不到空穴化结构.提出了形成空穴化结构可能的机理.运用选择性溶剂蒸气和一元酸分别处理胶束薄膜,得到了相同的表面形貌.     

溶剂对SBS溶液浇铸膜形态结构及性能影响

聚苯乙烯 聚丁二烯 聚苯乙烯 (ＳＢＳ)嵌段共聚物所兼具的高弹性与热塑性来源于其独特的微观相分离结构 ,其形态结构与性能的关系长期以来一直倍受人们的关注 .对于这种微相分离体系 ,除了传统意义上的良溶剂 (对两种嵌段均具有良好的溶解性 ,又称非选择性溶剂 )与不良溶剂外 ,还存在着对两种嵌段中的一种溶解性较好 ,对另一种溶解性较差的选择性溶剂[1,2 ].在溶液浇铸成膜过程中 ,不同溶剂与组成共聚物的两种嵌段的相互作用参数的差异将导致溶液中大分子构象的差异以及微观相分离过程的差异 ,从而影响浇铸膜的形态以及性能[3].本文首先利用…     

聚苯乙烯-b-聚丙烯酸/聚苯乙烯在水中的自组装及胶束尺寸的研究

利用动态光散射、透射电镜研究了嵌段共聚物聚苯乙烯 b 聚丙烯酸(PS b PAA)与均聚物聚苯乙烯(PS)在选择性溶剂水中的自组装行为.由于均聚物PS与PS嵌段具有相同的结构单元,均聚物PS参与胶束的形成,和嵌段共聚物的PS链段一同组成胶束的核;在适当的均聚物分子量和含量条件下,PS b PAA PS可以自组装形成单分散的纳米胶束;通过改变体系中均聚物PS的分子量和含量可在较大范围内调变胶束的尺寸.     

聚苯乙烯-聚甲基丙烯酸甲酯两嵌段共聚物薄膜在丙酮蒸汽退火下的形貌演化

用敲击模式原子力显微镜研究了聚苯乙烯-聚甲基丙烯酸甲酯(PS-b-PMMA)两嵌段共聚物薄膜形貌在丙酮蒸汽退火下随时间的演化过程.对于对称的嵌段共聚物薄膜(fPS≈fPMMA,fPS为PS-b-PMMA中PS的体积分数,fPMMA为PMMA的体积分数),通过控制膜厚和平衡态时相周期的比值可以使不同分子量的嵌段共聚物薄膜都实现由蠕虫状结构到孔洞再到条纹的形貌演化过程;对于非对称的嵌段共聚物薄膜,发现当聚苯乙烯组分含量较少(25%,36%)时,薄膜的形貌由无序态分别转变为规则排列的小球和直接转变为条纹结构;而当聚苯乙烯组分含量较多(70%)时,薄膜的形貌则由无序态转变为较平整的表面结构.我们对不同形貌的形成机理进行了详细的讨论.     

Detection of free surface composition and molecular-level structural development of styrene(S)/butadiene(B) block copolymer films during a solution-to-film process

The surface chemical structure development in solution-cast styrene(S)/butadiene(B) block copolymer films as a function of solvent evaporation time was investigated using sum frequency generation vibrational spectroscopy(SFG).The surface structure formation of the styrene(S)/butadien(B) block copolymer(30 wt% PS) films during the solution-to-film process was found to be controlled mainly by dynamic factors,such as the mobility of the PB block in solution.For SB diblock copolymers,a pure PB surface layer was formed only when the film was cast by dilute toluene solution.With increasing concentration of casting solution,PB and PS components were found to coexist on the film surface,and the morphology of the PB component on the film surface changed from cylindrical rods to spheres.For SBS triblock copolymers,a small amount of PS component existed on the surface even if the film was cast by 1.0 wt% toluene solution.In addition,PS components at the outermost layer of the film increased and the length of PB cylindrical rods on the surface decreased with increasing concentration of casting solution.     

Solution properties of polystyrene–polybutadiene block copolymers

Dilute solution viscosity and osmotic pressure measurements were performed on polystyrene (PS), polybutadiene (PB), polystyrene–polybutadiene (SB) diblock and polystyrene–polybutadiene (SBS) triblock copolymers. Anionic polymerization was used in such a way that the molecular weight of the PS block was kept constant (ca. 10 000), while the molecular weight of the PB block varied from 18000 to 450000. The measurements were carried out at a fixed temperature of 34.20°C in three solvents, namely toluene, a good solvent for PS as well as for PB, dioxane, which is a good solvent for PS and almost a theta solvent for PB, and cyclohexane, which is nearly a theta solvent for PS and a good solvent for PB. The compositions of SB and SBS, as derived from kinetic data agree with ultraviolet measurements in CHCl₃ solutions. The viscosity and osmotic pressure results indicate that the properties of SB and SBS are similar. Their intrinsic viscosities and second virial coefficients can be calculated from their chemical compositions, molecular weight, properties of parent polymers, and values of the interaction parameter \documentclass{article}\pagestyle{empty}\begin{document}$\bar \beta _{{\rm SB}}$\end{document} between styrene and butadiene units, for molecular weights not exceeding approximately 10⁵. The magnitude of \documentclass{article}\pagestyle{empty}\begin{document}$\bar \beta _{{\rm SB}} $\end{document} varies with the solvent. The results suggest that the domains of the PS and PB blocks overlap to a great extent.     

等规聚丙烯/聚丁烯-1釜内合金的结构与性能

高分子材料的组成、 组分分布及链结构与宏观性能紧密相关. 因此, 分析多组分釜内合金材料的链结构特点与性能之间的关系至关重要. 采用升温淋洗分级的方法对两种采用序贯两段聚合原位合成的等规聚丙烯/聚丁烯-1(iPP/iPB)釜内合金在-30 ℃~140 ℃温度范围进行分级, 采用核磁共振波谱仪、 傅里叶变换红外光谱仪、 差示扫描量热仪和凝胶渗透色谱仪等表征了级分的链结构及序列分布、 热行为、 分子量(M_w)及分子量分布(M_w/M_n)等. 结果表明iPP/iPB合金主要由5种级分组成, 高等规聚丁烯(iPB)为主要组分, 同时含有少量的丁烯-丙烯嵌段共聚物(PB-b-PP)和等规聚丙烯(iPP)等. 随淋洗温度升高, PB-b-PP级分中PP嵌段长度逐渐增加, PB嵌段长度逐渐减小; 在相同的淋洗温度, 合金B的嵌段共聚物级分中PP嵌段较长且结晶较完善; 合金B中iPB组分及嵌段共聚物组分含量较高, 使得合金B具有较高的拉伸强度、 弯曲强度、 优异的抗冲击性能、 较高的维卡软化温度及较快的晶型转变速率.     

聚合物共混物的超高效液相色谱-空间排阻色谱在线联用分离与表征

黏合剂和涂料行业中, 聚合物共混物表征是分析的难题, 分离技术的研究一直备受关注. 本文设计并搭建了超高效液相色谱-空间排阻色谱在线联用系统(UHPLC-SEC), 采用羟基聚丁二烯(HTPB)考察了二维色谱系统的溶剂兼容性及正交性, 以苯乙烯-丁二烯嵌段共聚物(SBS)、 苯乙烯-异戊二烯嵌段共聚物(SIS)和聚甲基丙烯酸酯(PMMA)共混物研究了二维色谱系统的适用性. 结果表明, HTPB分子量及分布的UHPLC-SEC测定结果与SEC测定结果一致, 峰尖分子量(M_p)为3407 Da, 重均分子量(M_w)为6573 Da, 分散系数(PDI)为2.36, 相对标准偏差(RSD)均小于5.7%, 系统的溶剂兼容性和正交性良好. UHPLC-SEC法测得聚合物共混物中PMMA, SBS和SIS的M_p, M_w和PDI与单个聚合物的SEC测定结果的相对误差均小于7.1%. PMMA, SBS和SIS共混物在200 °C加热3 h后, PMMA 稳定不变, SBS和SIS组分明显降解. UHPLC-SEC在线联用方法对聚合物共混物的表征结果准确、 重复性好, 为聚合物配方产品的失效分析提供了一种重要且有效的手段.     

成膜溶剂与氟化嵌段共聚物膜的表面富集行为

利用接触角、XPS、SFG、AFM等技术研究了环己酮、甲苯和三氟甲苯为成膜溶剂所得聚甲基丙烯酸甲酯-b-聚（甲基丙烯酸-2-全氟辛基乙酯）（PMMA—b—PFMA）嵌段共聚物膜的表面结构与性能．发现浇铸成膜时成膜溶剂对聚合物氟化组分向表面富集程度的影响相对较小,而旋涂成膜时溶剂的影响很大．不管以何种形式成膜,三氟甲苯溶剂最有利于氟化组分向表面富集,甲苯次之,环己酮最差．这一现象与溶剂的挥发速度无关．聚合物在溶液中的聚集结构、气／液界面结构是造成成膜方式对聚合物表面结构与性能产生巨大影响的主要原因．当聚合物在溶液中形成以PFMA为核、PMMA为冠的胶束结构时,在溶液固化过程中氟化组分向表面富集需要较长的时间,这时由于成膜方法直接影响溶液的固化速度,造成其对氟化组分向表面富集的程度影响很大．当聚合物在溶液中以单分子或松散聚集体存在,在溶液固化过程中氟化组分向表面富集的速度很快,这时成膜方法对氟化组分向表面富集的程度影响很小．以上结果无论对理论研究还是应用研究都具有重要意义．     

Block copolymers as compatibilizers for blends of linear low density polyethylene and polystyrene

Compatibilization of blends of linear low-density polyethylene (LLDPE) and polystyrene (PS) with block copolymers of styrene (S) and butadiene (B) or hydrogenated butadiene (EB) has been studied. The morphology of the LLDPE/PS (50/50) composition typically with 5% copolymer was characterized primarily by scanning electron microscopy (SEM). The SEB and SEBS copolymers were effective in reducing the PS domain size, while the SB and SBS copolymers were less effective. The noncrystalline copolymers lowered the tensile modulus of the blend by as much as 50%. Modulus calculations based on a coreshell model, with the rubbery copolymer coating the PS particle, predicted that 50% of the rubbery SEBS copolymer was located at the interface compared to only 5–15% of the SB and SBS copolymers. The modulus of blends compatibilized with crystalline, nonrubbery SEB and SEBS copolymers approached Hashin's upper modulus bound. An interconnected interface model was proposed in which the blocks selectively penetrated the LLDPE and PS phases to provide good adhesion and improved stress and strain transfer between the phases. © 1995 John Wiley & Sons, Inc.     

Nanostructured carbon black filled polypropylene/polystyrene blends containing styrene-butadiene-styrene copolymer: Influence of morphology on electrical resistivity

This paper is part of a comprehensive study on using selective localization of carbon black (CB) at the interface of immiscible polymer blends in order to reduce the percolation threshold concentration and enhance the conductivity of the blends. CB was successfully localized at the interface of polypropylene/polystyrene (PP/PS) blend by introducing styrene-butadiene-styrene (SBS) tri-block copolymer to the blend. In CB-PP/PS/SBS blends, CB has higher affinity for the polybutadiene (PBD) section of the SBS copolymer, whereas in CB-PP/PS blends, CB prefers the PS phase. PP/PS interface is one of the preferred locations for the SBS copolymer in the (PP/PS) blend; at which the PBD section of the SBS copolymer forms a few nanometers thick layer able to accommodate the CB nano-particles. The influence of SBS addition on the morphology and electrical properties of various PP/PS blends filled with 1 vol% CB were studied. SBS influence on the conductivity of PP/PS blends was found to be a function of the PP/PS volume ratio and SBS loading. The most dramatic increase in conductivity was found in the (60/40) and (70/30) PP/PS blends upon the addition of 5 vol% SBS. 5 vol% SBS was found to be the optimum loading for most blends. Using 10 vol% of SBS was reported to deteriorate electrical conductivity of the conductive co-continuous PP/PS blends. For all blends studied, SBS addition was found to compatibilize the blends. Finer morphologies were obtained by increasing SBS loading.     

Synthesis,structure, and swelling behavior of two-component copolymer networks

A two-component copolymer network comprising polystyrene (PS) and poly(dimethylsiloxane) (PDMS) as copolymer components was prepared by cross-linking PS with telechelic PDMS with a new method. The microphase structure of the dry PS/PDMS network was found to be irregular from DSC and small angle X-ray scattering measurements. The swelling behavior was observed in three kinds of mixed solvents which were chosen so as to contrast with one another in respect of solubility of the component polymers. The observed swelling degree depended on the solvent composition in a manner peculiar to the respective mixed solvent systems. The Flory swelling equation extended to the two-component polymer network qualitatively reproduced the experimental swelling behavior.