抑制型电导检测离子色谱法测定饮用水中高氯酸盐

建立抑制型电导检测离子色谱法测定饮用水中的高氯酸盐。选用IonPac^?AS19色谱柱(250 mm×4 mm)，柱温为30℃，电导池温度为35℃，用40 mmol/L氢氧化钾溶液作为淋洗液，氢氧化钾淋洗液由淋洗液发生器在线产生，淋洗液流量为1.0 mL/min，淋洗方式为等浓度淋洗。采用AERS 500(4 mm)型抑制器，抑制器电流为99 mA，进样体积为500μL，高氯酸盐的色谱峰面积与质量浓度在0.030～0.200 mg/L范围内的线性关系良好，相关系数为0.999 2，方法检出限为0.002 mg/L，定量限为0.010 mg/L。7次重复测定结果的相对标准偏差为2.49%～3.78%，样品加标回收率为90.0%～101%。该方法适用于饮用水中高氯酸盐的检测。     

超高含量氯离子基体下痕量亚硝酸盐的检测

介绍了一种无需对样品进行除氯处理,采用全新的离子色谱柱,抑制型电导离子色谱法检测,测定超高Cl-基体下痕量亚硝酸盐及其它常见阴离子的方法.其中Cl-浓度与亚硝酸盐浓度比可达到50000:1甚至100000:1,实现良好分离.选择色谱条件为:IonPac AS23阴离子交换柱,手工配制碳酸盐淋洗液等度淋洗,抑制型电导检测.污水样品通过Dionex OnGuardⅡRP柱和0.22 μm微孔尼龙膜处理.该方法采用25 μL进样,8种常见阴离子的检出限为0.2～5.8μg/L,线性范围均超过2个数量级,相关系数r在0.9996～0.9999的范围内,连续11次进样检出所有阴离子的RSD均小于5%,加标回收率结果在93%～106%之间.该方法具有选择性好,灵敏度高,操作简单等特点,从根本上解决了高氯离子基体中痕量亚硝酸盐及其它常见阴离子检测的问题,用于实际污水样品的检测.     

二维离子色谱法测定海水中的铵离子

研究了二维离子色谱测定海水中铵离子的方法。海水样品经10倍稀释,一维色谱采用高容量的CS–165 mm柱,以30 mmol/L甲磺酸溶液等度淋洗,流量为1 m L/min,进样25μL,CSRS–300 4 mm抑制电导分离Na+,NH4+;二维色谱采用CS–12A 4 mm柱,以8 mmol/L甲磺酸溶液等度淋洗,流量为1 m L/min,以1 300μL定量环进样,SC–CSRS–300盐转换器抑制电导检测NH4+。结果表明:色谱峰面积与NH4+质量浓度线性相关,相关系数为0.999 9。10μg/L标准溶液测定结果的相对标准偏差为2.7%(n=7),NH4+的方法检出限和仪器检出限分别为0.42,0.05μg/L,海水中NH4+加标回收率为80.8%~105.8%。     

离子色谱法检测植物提取液中痕量氟

介绍了一种采用OnGuardⅡ H柱进行样品前处理,抑制型电导离子色谱法检测,测定经管式炉燃烧水解后的浓碱性植物提取液中痕量氟的方法。色谱柱为:氢氧化物选择性的IonPac AS18阴离子交换柱,氢氧化钠等度淋洗。样品通过Dionex OnGuardⅡ氢型聚苯乙烯基强酸性树脂柱和0.22μm微孔尼龙膜处理。该方法检出限(S/N=3)为0.64μg/L,线性相关系数r=0.999 9,RSD为2.6%,回收率为95%~101%,具有灵敏度高,选择性好,操作简单,节省时间等特点,用于实际样品的检测,结果令人满意。     

离子色谱法测定酱油中乙酰丙酸

建立了离子色谱法测定酱油中乙酰丙酸含量的方法,并用于实际样品的检测.样品经前处理后,进入离子色谱系统进行分析,乙酰丙酸能有效地分离.选择色谱条件为:AS18 HC离子色谱分析柱,KOH等度淋洗,抑制型电导检测.采用外标法定量,乙酰丙酸浓度与其峰面积在一定浓度范围内有良好的线性关系,相关系数为0.9998.该方法的检出限(S/N=3)为O.015 mg/L,RSD 小于5.8%,回收率为92.0%～102.4%.     

离子色谱法测定氯膦酸二钠及其制剂的含量和有关物质

采用抑制型电导检测-离子色谱法同时测定氯膦酸二钠及其制剂的含量和有关物质.色谱条件为阴离子交换色谱柱(IonPac AS11-HC);检测方式为抑制电导检测;柱温30 ℃;流速1.2 mL/min;以KOH溶液为淋洗液,含量测定采用等度洗脱,有关物质检查采用梯度洗脱.氯膦酸二钠在0.0568～0.1895 g/L范围内线性关系良好(r＝0.9999); 注射液和胶囊的平均回收率分别为100.1%(RSD=0.7%)和98.9%(RSD=0.6%);检出限为0.3 ng.各杂质与主成分色谱峰能完全分离.     

离子色谱法测定废水中的六氟磷酸根

建立了离子色谱-抑制电导测定废水中六氟磷酸根的分析方法.采用IonPac AG23+IonPac AS23阴离子交换柱分离,流速1 mL/min,KOH等度淋洗,抑制型电导检测.采集的样品经过0.22µm滤膜、C18柱、On-Guard Na柱处理后进样分析.以信噪比S/N=3计算检出限,六氟磷酸根的检出限为0.02 mg/L.方法线性相关系数r为0.9997,试验结果峰面积的相对标准偏差为1.85%,实际样品的加标回收率在94.0%~103.3%之间.方法简便、结果准确,可以用于实际样品检测.     

大体积进样离子色谱法测定环境水样中高氯酸根

采用大体积500μL进样离子色谱法,电导检测测定了几种水体中高氯酸盐的含量。分析柱为容量高、亲水性强的以脂肪族碳骨架为基质的阴离子交换柱IonPac AS20,淋洗液在线发生器自动产生35 mmol/LKOH淋洗液,0.25 mL/m in等浓度淋洗。这种新型的以脂肪族碳骨架为基质的阴离子交换柱的采用,极大的削弱了该色谱柱对对氯苯磺酸的保留,完全消除了现行美国EPA高氯酸盐分析方法中高氯酸根与对氯苯磺酸共淋洗的问题。方法对高氯酸根的检出限(S/N=3)为0.5μg/L,高氯酸根浓度在1~1000μg/L范围内具有良好的线性(r=0.9991)。将本方法应用于自来水、河水和雪水样品中高氯酸盐的检测,实际样品的加标回收率在87%~114%之间;1μg/L高氯酸根连续进样9次,色谱峰面积相对标准偏差(RSD)为6.9%。     

离子色谱法测定水环境中高浓度Na~+存在下的痕量NH_4~+

采用0.45μm滤膜过滤处理样品和梯度淋洗离子色谱法测定水环境中高浓度Na+存在下的痕量NH4+含量。离子色谱条件为:IonPac CS16离子分析柱,甲基磺酸梯度淋洗,抑制型电导检测。用该法对炼厂水环境中高浓度Na+存在下的痕量NH4+的测定,Na+和NH4+加标回收率分别为100.24%～100.8%、91.30%～104.35%。     

离子色谱法(IC)分析小麦中的矮壮素和缩结胺

建立了离子交换色谱-直接电导法同时测定小麦中矮壮素和缩结胺残留的分析方法。样品磨碎超声提取后,过固相萃取(SPE)柱去除蛋白质,用0.22μm膜过滤,进样检测。考察了不同的阳离子色谱柱SH-CC-1、SH-CC-2、SH-CC-3,不同的淋洗液对矮壮素、缩结胺的保留时间和分离度的影响。确定了最佳色谱条件为SH-CC-3阳离子色谱柱,直接电导检测,淋洗液选用甲烷磺酸(3.0mmol/L)分离;流速1.0mL/min;柱温40℃;进样量100μL。在此条件下,矮壮素及缩结胺在0.20～20.0mg/L范围内,线性相关系数r均大于0.999,矮壮素和缩结胺的检出限分别为0.070和0.073mg/L,矮壮素、缩结胺的加标回收率分别为76.0%～93.8%和74.9%～91.2%,相对标准偏差在4.2%以下。方法选择性好,灵敏度高,抗干扰能力强,适用于检测小麦中矮壮素和缩结胺的含量。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.