单晶LaB6场发射阵列的电化学腐蚀工艺

 六硼化镧（LaB₆）场发射尖锥阵列的刻蚀工艺是制备LaB₆场发射阵列阴极的关键。在(111)面单晶LaB₆基片上,用等离子体增强化学气相沉积法制备氮化硅层做掩膜,光刻后采用电化学腐蚀方法对基片进行刻蚀,得到具有一定高度的LaB₆尖锥场发射阵列。讨论了单晶LaB₆的电化学腐蚀机理。改变各种电化学腐蚀参数,包括电解液成分、电解液浓度、阳极所加电压,用电子扫描显微镜观察样品形貌。结果发现H₃PO₄是刻蚀单晶LaB₆的理想电解液,它克服了过去电化学实验中经常遇到的尖锥各向异性问题。随着电解液浓度或阳极电压的增大,尖锥高度增加,但是基底表面变得更为粗糙。另一方面,阳极电压太小时,有横向刻蚀现象产生,不利于提高发射体的场增强因子。此外,在二极管结构中初步测试了LaB6尖锥场发射阵列的电流发射特性,在真空度2×10^-4 Pa、极间距离0.1 mm、阳极电压900 V下,发射电流达到13 mA。     

六硼化镧场发射阴极阵列的制作及特性

 采用氧等离子体氧化刻蚀工艺,制备出尖锐的六硼化镧（LaBLaB₆）微尖锥场发射阵列。在二极管结构中测试了LaB₆-FEAs的场发射性能,得到了真空度为5×10^-5 Pa 下的I-V曲线及相应的Fowler-Nordheim节点。结果表明,由于LaBLaB₆材料较低的逸出功,使得阴极的开启电压较小,开启场仅为7 V/μm。此外,将氧等离子体氧化刻蚀方法与氩氧等离子体刻蚀方法和电化学刻蚀方法进行了比较,表明氧等离子体氧化刻蚀方法是制备LaB₆场发射阴极阵列的一种理想工艺。     

LaB6场发射尖锥的场发射特性研究

 报道了六硼化镧（LaB₆）场发射尖锥的场发射性能。采用电化学腐蚀方法制作了LaB₆场发射尖锥，并在10^-2～10^-7 Pa 的宽真空度范围内对单尖LaB₆场发射二极管的发射特性进行了测试。发现残余气体电离产生的离子轰击对LaB₆场发射阴极尖锥表面起到了离子清洗作用，使LaB₆场发射尖锥在低真空工作后发射电流大幅度提高。离子轰击是一种适用于LaB₆场发射阴极的激活处理方法。     

大面积环状LaB6阴极

 介绍了一种用于管状电子束发射的大面积LaB₆阴极电子源，其阴极发射面积为115 mm²，LaB₆发射体用钼作基底，在LaB₆与钼之间用耐高温的碳化物粘合剂填充以防止LaB₆与钼发生反应。采用电子束轰击的方式加热LaB₆发射体，当阴极温度为1 873 K时，加热功率为173 W，直流发射电流密度达到40 A/cm²。与用石墨加热LaB₆发射体相比，该电子源加热功率降低了66%。阴极在室温下反复暴露于大气后其发射性能稳定。     

射频电子枪中LaB6阴极的研究

 一种用于射频电子枪中的LaB₆热阴极已经研制成功。分别研究了(100)、 (110)、(111) 晶向LaB₆单晶的热发射特性。选用(100)晶向的LaB₆单晶材料作为发射体并用铼做基底材料。试验表明,在1823K工作条件下,其热发射电流密度达到 30A/cm²;在真空条件为5×10^-5Pa下,寿命已达10000小时以上。在室温下反复多次暴露大气后,其发射性能保持不变。     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术，分别沉积Ti和Ti/Al膜，经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序，分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27     

高功率激光宽光谱减反膜的溶胶-凝胶旋转法制备工艺

 采用溶胶-凝胶法用旋转镀膜工艺在K9玻璃基片上制备出了SiO₂和有机硅单层减反膜以及有机硅-SiO₂双层减反膜。考察了旋转速度对SiO₂和有机硅单层膜的中心透射波长、膜层折射率等基本光学性质的影响，实验确定了双层膜的涂敷工艺。透射光谱测量表明，采用本文工艺条件制备的有机硅 SiO₂双层膜在430～800nm范围内透射率达99％以上。     

利用胶体小球掩蔽刻蚀技术制备的半导体纳米阵列的场电子发射特性

利用胶体小球掩蔽刻蚀技术,制备了单晶硅纳米阵列,利用原子力显微镜观察了硅阵列的表面形貌,实验结果表明,硅柱阵列具有高密度和较好的均匀性。同时研究了单晶硅纳米阵列的场电子发射特性。为了提高样品的场发射性能,在所制备的单晶硅有序纳米阵列上生长了一层非晶碳薄膜。与单晶纳米硅柱阵列相比,覆盖有非晶碳膜的样品的场电子发射特性有了明显的改善,表现在场发射的开启电场下降,同时场发射增强因子得到增加。结果表明非晶碳膜确实能够降低电子发射的表面有效势垒,从而增强了场电子发射特性。     

ZrO2/ SiO2多层膜的化学法制备研究

 分别以ZrOCl₂·8H₂O 和正硅酸乙酯为原料,采用溶胶-凝胶工艺制备了性能稳定的ZrO₂和SiO₂溶胶。用旋转镀膜法分别在K9玻璃和单晶硅片上制备了ZrO₂/ SiO₂多层膜。采用溶剂替换和紫外光处理等手段,有效地解决了ZrO₂/SiO₂多层膜中膜层开裂和膜间渗透等问题。应用扫描电子显微镜观测了薄膜的表面和剖面微观形貌,并用椭偏仪测得薄膜的厚度和折射率,研究了薄膜厚度、折射率与热处理温度、紫外光处理时间的关系,对所获得薄膜的紫外-可见、红外光谱进行了分析。用输出波长1064nm ,脉宽15ns 的电光调Q光系统产生的强激光进行了单层膜的辐照实验,结果发现溶剂替换后激光损伤阈值有所提高。     

表面层对1 064 nm高反射镜损伤阈值影响

 采用电子束蒸发的方法制备了３种具有不同表面层材料及结构的中心波长为1 064 nm的零度高反镜,３种膜系表面层分别为1/4波长光学厚度的HfO₂,1/2波长光学厚度的SiO₂,以及1/4波长光学厚度的SiO₂。光谱测试表明：三者在1 064 nm处均有较高的反射率（高于99.8%）,利用热透镜的方法测量得到３个膜系辐照激光正入射情况下,薄膜对光的吸收比例分别为3.0×10^-6,5.0×10^-6和6.5×10^-6,其损伤阈值分别为32.5,45.2和28.4 J/cm²。并在膜层内部电场分布和膜层材料物理特性的基础上分析了３种不同表面层膜系吸收和损伤阈值差别的原因。     

基于InP/ZnS核壳结构量子点的色转换层设计及制作

提出了采用环境友好型InP/ZnS核壳结构量子点材料制备匹配蓝光Micro-LED阵列的量子点色转换层以实现Micro-LED阵列器件全彩化的技术方案。通过采用倒置式量子点色转换层方案,实现了InP/ZnS量子点材料和Micro-LED阵列的非直接接触,从而可以缓解LED中热量聚集导致的量子点材料发光主波长偏移、半峰宽展宽以及发光效率衰减等问题。量子点色转换层中内嵌PDMS聚合物柔性膜层,可以消除咖啡环效应,同时,色转换层中内嵌飞秒激光图案化处理的500 nm长波通滤光膜层,可以抑制蓝光从非蓝色像素单元出射。最后,实验制备了像素单元中心间距90μm的16×16 InP/ZnS量子点色转换层。该设计可以实现基于蓝光Micro-LED阵列的全彩色Micro-LED显示器件的制备,并且该制备方法可以降低全彩色Micro-LED阵列显示器件的制备成本。     

Growth, modulation and photoresponse characteristics of vertically aligned ZnO nanowires

Vertically aligned, c-axis oriented zinc oxide (ZnO) nanowires were grown on Si substrate by metal organic chemical vapor deposition (MOCVD) technique, where sputtered aluminum nitride (AlN) film was used as an intermediate layer and thermally evaporated barium fluoride (BaF₂) film as a sacrificial layer. The aspect ratio and density of the nanowires were also varied using only Si microcavity without any interfacial or sacrificial layer. The UV detectors inside the microcavity have shown the higher on-off current ratio and fast photoresponse characteristics. The photoresponse characteristics were significantly varied with the aspect ratio and the density of nanowires.     

A potential commercial surface‐enhanced Raman scattering–active substrate: stability and usability

In this article, a surface‐enhanced Raman scattering (SERS)–active substrate with great stability and usability is reported. It is composited with a two‐dimensional ordered array of Ag spherical caps and an aluminum coating. The ordered aluminum template formed during the synthesis of anodic aluminum oxide film was used as the patterned matrix. After sputtering a Ag layer and then peeling off the aluminum template, the patterned structure was replicated on Ag layer. The aluminum template could serve as a coating that protected Ag from being oxidized. Ultraviolet‐visible reflection measurement was performed to monitor the adsorption process of probing molecules. Taking 4‐mercaptopyridine as probing molecules, SERS spectra were investigated. Comparing with the ordinary Ag film, the patterned Ag layer exhibited better SERS activity. The convenience for preparing, storing, and using makes it a promising candidate for SERS application in the fast field analysis. Copyright © 2012 John Wiley & Sons, Ltd.     

Field electron emission changes by face specific adsorption of aluminum oxide and corresponding decomposition products on tungsten {110} and {100} planes

After deposition of aluminum oxide on a tungsten field emission microscope (FEM) tip and stepwise heating, three stages of emission changes were observed on {100}. Stages I and II cause work function decreases of 0.28 and 0.07 eV, respectively. Stage III is characterized by a large increase (Δ??+3 eV). The changes are discussed in terms of interaction of decomposition products (oxygen and aluminum) and adsorption of aluminum oxide. On {110} only a single aluminum oxide layer growth, which results in a work function decrease to ?=4.69 eV, is observed. The field electron emission from this layer was measured between 1400°K and room temperature. The experimental values were compared with those determined from Christov's unified theory of field and thermionic emission. The {110} layer values coincide with those obtained earlier from an aluminum oxide covered tungsten {112}.     

Superconducting membrane mechanical oscillator based on vacuum-gap capacitor

Using the diluted S1813 UV photoresist as a sacrificial layer, we successfully fabricate a superconducting suspended parallel-plate capacitor, in which the top layer of aluminum film acts as a membrane mechanical resonator. Together with a superconducting octagonal spiral inductor, this parallel-plate capacitor constitutes a superconducting microwave resonator. At m K temperature, the transmission characteristic and spectrum of the microwave resonator are measured.Sideband frequencies caused by the vibration of the membrane mechanical resonator are clearly demonstrated. By downconverting with a mixer, the dependence of fundamental frequency and its harmonics on the input microwave power are clearly demonstrated, which is consistent with the numerical simulation.     

Field emissions of graphene films deposited on different substrates by CVD system

<正>Graphene films are deposited on copper(Cu) and aluminum(Al) substrates,respectively,by using a microwave plasma chemical vapour deposition technique.Furthermore,these graphene films are characterized by a field emission type scanning electron microscope(FE-SEM),Raman spectra,and field emission(FE) I-V measurements.It is found that the surface morphologies of the films deposited on Cu and Al substrates are different:the field emission property of graphene film deposited on the Cu substrate is better than that on the Al substrate,and the lowest turn-on field of 2.4 V/μm is obtained for graphene film deposited on the Cu substrate.The macroscopic areas of the graphene samples are all above 400 mm~2.     

Shadowgraphy investigation of laser-induced forward transfer: Front side and back side ablation of the triazene polymer sacrificial layer

Thin films of a photodecomposible triazene polymer are used as sacrificial layer for the micro-deposition of sensitive materials by laser-induced forward transfer. To understand the ablation process of this sacrificial layer, the ultraviolet laser ablation of triazene films was investigated by time-resolved shadowgraphy. Irradiation from the film side shows a complete decomposition into gaseous fragments, while ablation through the substrate causes ejection of a solid flyer of polymer. The occurence of the flyer depends on the film thickness as well as on the applied fluence, and a compact flyer is obtaind when these two parameters are optimized.     

有机薄膜在平面光学微腔中的光致发光特性

本文研究了有机薄膜在平面光学微腔中的光致发光特性。有机光学微脸以多层介质膜和金属银分别作为反射镜,８－羟基喹啉铝（Ａｌｑ）为发光层。Ａｌｑ薄膜的荧光峰位于５１９ｎｍ,谱线的半高全宽为９０ｎｍ。微腔的荧光峰位于５３０ｎｍ,谱线的半高全宽窄化至１０ｎｍ。谐振波长处的发射强度提高了一个数量级。     

改进的SILAR法制备ZnO薄膜及其表征

采用一种改进的液相成膜技术——连续离子层吸附与反应(SILAR)法, 用锌氨络离子\[Zn(NH3)4\]2+ 溶液作为独立的前驱体溶液, 以载玻片为衬底, 在(125±5) ℃的温度下沉积出致密、 透明的ZnO薄膜。 分别用冷场发射型扫描电镜(FESEM)和X射线衍射(XRD)分析了薄膜样品的表面形貌和结晶状态, 用紫外可见分光光度计(UV-Vis spectroscopy)研究了薄膜样品的发光性能。 结果表明: 获得样品为六角纤锌矿结构的多晶薄膜材料沿\[002\]方向择优生长; 样品表面均匀、 致密, 厚度约为550 nm;在可见光波段具有高的透射率(＞80％)。 A modified solution method,successive ionic layer adsorption and reaction(SILAR),was applied to prepare transparent zinc oxide(ZnO) film on glass substrate at (125±5) ℃ in mixed ion precursor solution. The surface morphology and crystallizations of films were analyzed by field emission scanning microscopy(FESEM) and X ray diffraction(XRD), respectively. The optical properties of the films were studied by ultraviolet visible(UV Vis)spectroscopy. The results show that the obtained samples are polycrystalline films of hexagonal wurtzite structure,with the preference of [002\] orientation. The as deposited films exhibit uniform and compact surface morphology, with the film thickness of 550 nm, and have high transmittance in the visible band(＞80％).