SO42-/TiO2固体超强酸新制备方法及其对形成邻苯二甲酸二丁酯的催化活性

建立了用钛白粉制备固体超强酸SO4^2-/TiO2的新方法．考察了超强酸SO4^2-/TiO2的制备条件对催化邻苯二甲酸酐和正丁醇酯化反应的催化活性的影响．实验表明，以合成的超强酸为催化剂，在160℃反应4h，邻苯二甲酸二丁酯的产率大于99％．     

固体超强酸SO_4~(2-)-MoO_3-TiO_2的制备及其催化酯化性能研究

ＳＯ2 -4 ＭｘＯｙ 型固体超强酸自问世以来一直受到人们的广泛关注 ,已对其进行了大量的研究。该类催化剂的酸强度高 ,在烷基化、酰基化、裂解、醇脱水、异构化、酯化等反应中有很高的催化活性。最常用的氧化物基体是ＺｒＯ2 和ＴｉＯ2 ,最好的促进剂是ＳＯ2 -4 。也有用ＭｏＯ3作促进剂的[1～3] ,得到相应的超强酸催化剂。作者在ＳＯ2 -4 ＴｉＯ2 超强酸的基础上 ,将ＭｏＯ3和ＳＯ2 -4 同时负载在ＴｉＯ2基体上 ,得到ＳＯ2 -4 ＭｏＯ3 ＴｉＯ2 固体超强酸 ,以乙酸异戊酯的合成为探针反应考察了该催化剂的催化酯化活性 ,并与ＳＯ2 -4 …     

焙烧温度对纳米级SO2- 4/TiO2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO2- 4/TiO2固体超强酸,考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响.结果显示该催化剂在450℃焙烧3 h,可以形成纳米级SO2-4/TiO2固体超强酸的结构.用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98.4%.     

SO_4~(2-)/TiO_2固体超强酸新制备方法及其对形成邻苯二甲酸二丁酯的催化活性

建立了用钛白粉制备固体超强酸SO42-/TiO2的新方法.考察了超强酸SO42-/TiO2的制备条件对催化邻苯二甲酸酐和正丁醇酯化反应的催化活性的影响.实验表明,以合成的超强酸为催化剂,在160℃反应4h,邻苯二甲酸二丁酯的产率大于99%.     

固体超强酸SO2-4/TiO2负载Tm改性的研究

负载稀土元素Tm以改性SO4^2-/TiO2,制备出固体超强酸催化剂Tm -SO4^2-/TiO2,并用于催化柠檬酸与正丁醇的酯化反应,考察了Tm的负载对催化剂性能的影响,并借助吡啶吸附的程序升温脱附（Py-TPD）法、差热分析（DTA）、热重分析（TGA）、红外光谱（IR）法研究其结构与性能的关系,实验结果表明,Tm的负载,使催化剂的催化活性有所提高,Tm的加量为催化剂量的3%时制得的Tm- SO4^2-/TiO2,其催化酯化反应的转化率为94.4%;Tm的负载能显著降低催化剂表面的积炭量,并且有效抑制So4^2-的流失,使Tm- SO4^2-/TiO2催化剂具有良好的稳定性,重复使用5次后反应的转化仍高达93.1%。     

SO2-4/TiO2-SiO2固体超强酸的结构及其光催化性能

自从Arata等[1]首次报道无卤素型SO2-4/MxOy固体超强酸体系以来, 对该类催化剂的研究引起了人们的广泛重视. 大量研究工作表明, 固体超强酸催化剂对丁烷异构化、苯衍生物烷基化、链烷烃裂解和乙烯二聚等诸多酸催化的反应表现出极高的反应活性[2]. 最近, 我们把SO2-4/TiO2型固体超强酸应用于有机物的光催化氧化反应, 研究发现TiO2光催化剂经H2SO4浸渍处理形成固体超强酸后, 催化剂的光催化活性大大提高, 并具有很好的反应活性、稳定性和抗湿性能[3];     

焙烧温度对纳米级SO_4~(2-)/TiO_2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO42-/TiO2固体超强酸,考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响.结果显示该催化剂在450℃焙烧3 h,可以形成纳米级SO42-/TiO2固体超强酸的结构.用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98.4%.     

固体超强酸SO /SiO2-TiO2催化合成异维生素C钠

在异维生素C钠（D-VcNa）的合成过程中,以SO4^2-/SiO2-TiO2复合固体超强酸作为酯化反应催化剂,2-酮基-D-葡萄糖酸（2-KGA）和甲醇为原料,采用精馏脱水酯化工艺,不断除去酯化过程中产生的水.催化剂的最佳焙烧温度为550℃,催化剂用量为2.5%;反应时间3～4 h,产品收率为88.6%,催化剂的重复使用性较好,催化体系优于硫酸法.     

TiO2基固体超强酸的制备及光催化性能研究

半导体氧化物TiO2对很多有机污染物吸附较强、催化氧化活性高,因此它在环境污染治理方面扮演极其重要的角色,被广泛用于光催化处理多种有机物,但常规二氧化钛半导体光催化剂较低的量子效率(约4%)使其应用受到一定程度的制约[1]。1979年H ino[2]等首次报道无卤素型SO42-/M xO y固体超强酸体系以来,引起化学工作者极大关注。固体超强酸催化剂如SO42-/TiO2,SbF5/SiO2/TiO2等是一类新型酸催化剂,广泛用于酯化反应、苯衍生物烷基化、烯烃齐聚等。研究发现,基于SO42-改性的TiO2固体超强酸催化剂对于有机物具有较高的光催化氧化活性[3,4],…     

焙烧温度对纳米级SO4^2-／TiO2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO4^2-／TiO2固体超强酸，考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响．结果显示该催化剂在450℃焙烧3h，可以形成纳米级SO4^2-／TiO2固体超强酸的结构，用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98．4％。     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

The preparation of NbH5(Me2PCH2CH2Me2)2 and NbHL2(Me2PCH2CH2PMe2)2 (L = CO or C2H4)

MMe₅(dmpe) (M = Nb or Ta, dmpe = Me₂PCH₂CH₂PMe₂) reacts with H₂ (500 atm) and dmpe in THF at 60°C to give MH₅(dmpe)_2? NbH₅(dmpe)₂ readily reacts with two mol of CO or ethylene (L) to give NbHL₂(dmpe)₂. The exchange of the hydride ligand with the ethylene protons in NbH(C₂H₄)₂(dmpe)₂ is not rapid on the ¹H NMR time scale (60 MHz) at 95°C.     

NaBO2-NaCl-Na2CO3, NaBO2- Na2CO3-NaMoO4, NaBO2- Na2CO3-NaWO4, and NaBO2-NaCl-Na2WO4 ternary systems

The phase diagrams of the NaBO₂-NaCl-Na₂CO₃, NaBO₂-Na₂CO₃-Na₂MoO₄, NaBO₂- Na₂CO₃-Na₂WO₄, and NaBO₂-NaCl-Na₂WO₄ ternary systems were studied by a calculation-experimental method and differential thermal analysis. The coordinates of ternary eutectics were determined: E ₁: 612°C, 16 mol % NaBO₂, 42 mol % NaCl, and 42 mol % Na₂CO₃; E ₂: 568°C, 12 mol % NaBO₂, 28 mol % Na₂CO₃, and 60 mol % Na₂MoO₄; E ₃: 575°C, 12 mol % NaBO₂, 32 mol % Na₂CO₃, and 56 mol % Na₂WO₄; E ₄: 628°C, 8 mol % NaBO₂, 20 mol % NaCl, and 72 mol % Na₂WO₄; and E ₅: 655°C, 9 mol % NaBO₂, 53 mol % NaCl, and 38 mol % Na₂WO₄.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

(H2NC4H8NCH2CH2NH2)(HNCH2CH2NH2)3Zn2Ge2Se8: A new,templated one-dimensional ternary semiconductor stabilized by mixed organic cations

The novel, 1D semiconductor (H₂NC₄H₈NCH₂CH₂NH₂)(HNCH₂CH₂NH₂)₃Zn₂Ge₂Se₈ has been synthesized under solvothermal conditions using N-(2-aminoethyl)piperazine as solvent and templating agent at 200 °C. The material was characterized by single crystal and powder X-ray diffraction, IR and Raman spectroscopy and thermogravimetric analysis. The compound consists of 1D anionic [Zn₂Ge₂Se₈]⁴⁻ chains made of alternating edge-shared [ZnSe₄] and [GeSe₄] tetrahedra that charged balanced by one N-(2-aminoethyl)piperazinium and three piperazinium cations. The optical properties were investigated with solid state UV–Vis/near IR spectroscopy and the results show that the solid is a medium gap semiconductor with an absorption edge at 1.8 eV.     

Polymorphism in the Sc2Si2O7-Y2Si2O7 system

This paper examines the structural changes with temperature and composition in the Sc₂Si₂O₇-Y₂Si₂O₇ system; members of this system are expected to form in the intergranular region of Si₃N₄ and SiC structural ceramics when sintered with the aid of Y₂O₃ and Sc₂O₃ mixtures. A set of different compositions have been synthesized using the sol-gel method to obtain a xerogel, which has been calcined at temperatures between 1300 and 1750 °C during different times. The temperature-composition diagram of the system, obtained from powder XRD data, is dominated by the β-RE₂Si₂O₇ polymorph, with γ-RE₂Si₂O₇ and δ-RE₂Si₂O₇ showing very reduced stability fields. Isotherms at 1300 and 1600 °C have been analysed in detail to evaluate the solid solubility of the components. Although, the XRD data show a complete solid solubility of β-Sc₂Si₂O₇ in β-Y₂Si₂O₇ at 1300 °C, the ²⁹Si MAS-NMR spectra indicate a local structural change at x ca. 1.15 (Sc_2−xY_xSi₂O₇) related to the configuration of the Si tetrahedron, which does not affect the long-range order of the β-RE₂Si₂O₇ structure. Finally, it is interesting to note that, although Sc₂Si₂O₇ shows a unique stable polymorph (β), Sc³⁺ is able to replace Y³⁺ in γ-Y₂Si₂O₇ in the compositional range 1.86?x?2 (where x is Sc_2−xY_xSi₂O₇) as well as in δ-Y₂Si₂O₇ for compositions much closer to the pure Y₂Si₂O₇.     

Synthesis and characterization of inorganic solid electrolytes of Li2O-SiO2-P2O5 and Li2O-TiO2-SiO2-P2O5 systems

The lithium-ion-conducting inorganic solid electrolytes in the oxide systems Li₂O-SiO₂-P₂O₅ and Li₂O-TiO₂-SiO₂-P₂O₅ were prepared by the solid-state reaction, and the electrolyte pellet made by cold-pressing method had diameter of 13 mm and was about 1 mm thick. Phase identification and surface morphology of the products were carried out by X-ray diffraction and scanning electron microscopy. Ionic conductivity of the pellets was investigated through ac impedance. The results show that the adding of other cations can improve the ionic conductivity of the solid electrolyte, and the sintering temperature and duration can influence the ionic conductivity. The maximum ionic conductivity in the samples is 9.9 × 10⁻⁴ S/cm in the Li₂O-TiO₂-SiO₂-P₂O₅ system. Original Russian Text ? W. Li, M. Wang, Z.H. Li, X.F. Shang, H. Wang, Y.W. Wang, Y.B. Xu, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 11, pp. 1341–1345.     

Tl2S-Sb2S3-Bi2S3 quasi-ternary system

The Tl₂S-Sb₂S₃-Bi₂S₃ quasi-ternary system (system A) was studied using DTA, X- ray powder diffraction, microstructure examination, and microhardness measurements. TlSbS₂-Tl₄Bi₂S₅(TlBiS₂, Bi₂S₃), Sb₂S₃-TlBiS₂, Tl₃SbS₃-TlBiS₂(Bi₂S₃), and [TlSb_0.5Bi_0.5S₂]-Tl₂S isopleths; isothermal sections at 500 K; and liquidus surface projection of system A were constructed. Characteristic features of the title system are extensive fields of solid solutions extended along the TlSbS₂-TlBiS₂ quasi-binary section and a continuous solubility belt 1–2 mol % wide extended along the Sb₂S₃-Bi₂S₃ binary subsystem. Primary separation fields of phases and the types and coordinates of invariant and monovariant equilibria in system A were determined.