固体超强酸SO_4~(2-)/TiO_2负载Tm改性的研究

负载稀土元素 Tm以改性 SO2 - 4 / Ti O2 ,制备出固体超强酸催化剂 Tm- SO2 - 4 / Ti O2 ,并用于催化柠檬酸与正丁醇的酯化反应 .考察了 Tm的负载对催化剂性能的影响 ,并借助吡啶吸附的程序升温脱附 (Py- TPD)法、差热分析 (DTA)、热重分析 (TGA)、红外光谱 (IR)法研究其结构与性能的关系 .实验结果表明 ,Tm的负载 ,使催化剂的催化活性有所提高 ,Tm的加量为催化剂量的 3%时制得的 Tm- SO2 - 4 / Ti O2 ,其催化酯化反应的转化率为94.4% ;Tm的负载能显著降低催化剂表面的积炭量 ,并且有效抑制 SO2 - 4 的流失 ,使 Tm- SO2 - 4 / Ti O2 催化剂具有良好的稳定性 ,重复使用 5次后反应的转化率仍高达 93.1%     

固体超强酸SO4^2——MoO3—TiO2的制备及其催化酯化性能研究

SO4^2--MxOy型固体超强酸自问世以来一直受到人们的广泛关注,已对其进行了大量的研究。该类催化剂的酸度强度高,在烷基化、酰基化、裂解、醇脱水、异构化、酯化等反应中有很高的催化活性。最常用的氧化物基体是ZrO2和TiO2,最后的促进剂SO4^2-。也有用MoO3作促进剂的^[1-3],得到相应的超强酸催化剂。作者在SO4^2--TiO2超强酸的基础上,将MoO3和SO4^2-同时负载在TiO2基体上,得到SO4^2--MoO3-TiO2固体超强酸,以乙酸异戊酯的合成为探针反应考察了该催化剂的催化酯化活性,并与SO4^2--TiO2、MoO3-TiO2的催化酯化活性作了比较。     

固体超强酸SO42-/TiO2在柠檬酸与正丁醇酯化反应中的催化性能研究

以固体超强酸SO4^2-/TiO2为催化剂合成柠檬酸三丁酯,研究了该催化剂在柠檬酸与正丁醇化反应中的催化活性和稳定性;考察了（MH4）2SO4用量、焙烧温度对催化剂结构、性能的影响;并借助Hammett指示剂法、XRD、AES分析,研究其结构与性能的关系。实验结果表明,在（MH4）2SO4用量为20％、焙烧温度为600℃条件下制得的催化剂,其催化剂选择性99％,锐钛矿TiO2（A）晶相的形成与完善,是提高催化选择性的关键因素;催化剂失活是由于积炭与SO4^2-的流失造成的。     

SO4^2-/TiO2催化合成乙酸戊酯

以Ti（OBu）4为原料，采用溶胶-凝胶法制备了固体超强酸SO4^2-/TiO2，其结构经XRD，DRS及IR表征。以SO4^2-/TiO2为催化剂，通过乙酸与戊醇反应合成了乙酸戊酯。讨论了影响酯化率的主要因素。实验结果表明，当催化剂用量为0．6g，乙酸87．3mmol，醇酸摩尔比为1．4：1．0，于115℃反应6h时，平行实验的平均酯化率可达94．2％。     

C2H4的微波场助气相光催化氧化

用溶胶－凝胶法制备了多孔性TiO2和SO4^2-/TiO2催化剂,对其结构进行了表征,并以C2H4为模型反应物考察了微波对催化剂的光催化氧化反应性能的影响。在微波场中TiO2和SO34^2-/TiO2催化剂的光催化氧化性能得到明显改善,无微波场时乙烯转化率分别为20％（TiO2)和41％（SO4^2-/TiO2),而在微波辐射和紫外光的同时作用下乙烯转化率分别提高到27％和62％,SO4^2-／TiO2催化剂的微波场助效应更为显著。     

SO42-/TiO2固体超强酸新制备方法及其对形成邻苯二甲酸二丁酯的催化活性

建立了用钛白粉制备固体超强酸SO4^2-/TiO2的新方法．考察了超强酸SO4^2-/TiO2的制备条件对催化邻苯二甲酸酐和正丁醇酯化反应的催化活性的影响．实验表明，以合成的超强酸为催化剂，在160℃反应4h，邻苯二甲酸二丁酯的产率大于99％．     

焙烧温度对纳米级SO4^2-／TiO2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO4^2-／TiO2固体超强酸，考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响．结果显示该催化剂在450℃焙烧3h，可以形成纳米级SO4^2-／TiO2固体超强酸的结构，用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98．4％。     

焙烧温度对纳米级SO2- 4/TiO2固体超强酸性能的影响

用锐钛型纳米TiO2制备了纳米级SO2- 4/TiO2固体超强酸,考查了焙烧温度对酸强度、比表面积、红外光谱及其催化活性的影响.结果显示该催化剂在450℃焙烧3 h,可以形成纳米级SO2-4/TiO2固体超强酸的结构.用该催化剂催化乙酸和丁醇酯化反应可使酯化率达到98.4%.     

固体超强酸SO /SiO2-TiO2催化合成异维生素C钠

在异维生素C钠（D-VcNa）的合成过程中,以SO4^2-/SiO2-TiO2复合固体超强酸作为酯化反应催化剂,2-酮基-D-葡萄糖酸（2-KGA）和甲醇为原料,采用精馏脱水酯化工艺,不断除去酯化过程中产生的水.催化剂的最佳焙烧温度为550℃,催化剂用量为2.5%;反应时间3～4 h,产品收率为88.6%,催化剂的重复使用性较好,催化体系优于硫酸法.     

镧对固体超强酸SO4^2-／TiO2／甜交联膨润土的改性研究

采用镧对固体超强酸SO4^2-／TiO2／铝交联膨润土（SO4^2-／TiO2／Al—PILC）进行改性，制备了La-SO4^2-／TiO2／Al—PILC稀土超强酸，并采用XRD、低温N2吸附法及吡啶吸附红外等方法对其进行了结构、表面性能及酸性的表征。实验结果表明，镧引入SO4^2-／TiO2／Al—FILC超强酸，对TiO2锐钛矿晶相的形成没有影响，但对锐钛矿晶相向金红石相的转变有抑制作用，镧的引入使催化剂的酸强度及酸中心的数量有所增加，镧能有效地减少催化剂表面SO4^2-的流失量，从而提高催化剂的活性稳定性。     

Sc2MgGa2 and Y2MgGa2

Scandium magnesium gallide, Sc₂MgGa₂, and yttrium magnesium gallide, Y₂MgGa₂, were synthesized from the corresponding elements by heating under an argon atmosphere in an induction furnace. These intermetallic compounds crystallize in the tetragonal Mo₂FeB₂‐type structure. All three crystallographically unique atoms occupy special positions and the site symmetries of (Sc/Y, Ga) and Mg are m2m and 4/m, respectively. The coordinations around Sc/Y, Mg and Ga are pentagonal (Sc/Y), tetragonal (Mg) and triangular (Ga) prisms, with four (Mg) or three (Ga) additional capping atoms leading to the coordination numbers [10], [8+4] and [6+3], respectively. The crystal structure of Sc₂MgGa₂ was determined from single‐crystal diffraction intensities and the isostructural Y₂MgGa₂ was identified from powder diffraction data.     

Zur Kenntnis der Dialkalimetalldichalkogenide β-Na2S2, K2S2, α-Rb2S2, β-Rb2S2, K2Se2, Rb2Se2, α-K2Te2, β-K2Te2 und Rb2Te2

On Dialkali Metal Dichalcogenides β-Na₂S₂, K₂S₂, α-Rb₂S₂, β-Rb₂S₂, K₂Se₂, Rb₂Se₂, α-K₂Te₂, β-K₂Te₂ and Rb₂Te₂ The first presentation of pure samples of α- and β-Rb₂S₂, α- and β-K₂Te₂, and Rb₂Te₂ is described. Using single crystals of K₂S₂ and K₂Se₂, received by ammonothermal synthesis, the structure of the Na₂O₂ type and by using single crystals of β-Na₂S₂ and β-K₂Te₂ the Li₂O₂ type structure will be refined. By combined investigations with temperature-dependent Guinier-, neutron diffraction-, thermal analysis, and Raman-spectroscopy the nature of the monotropic phase transition from the Na₂O₂ type to the Li₂O₂ type will be explained by means of the examples α-/β-Na₂S₂ and α-/β-K₂Te₂. A further case of dimorphic condition as well as the monotropic phase transition of α- and β-Rb₂S₂ is presented. The existing areas of the structure fields of the dialkali metal dichalcogenides are limited by the model of the polar covalence.     

The alkali hypophosphites KH2PO2, RbH2PO2 and CsH2PO2

The structures of the hypophosphites KH₂PO₂ (potassium hypophosphite), RbH₂PO₂ (rubidium hypophosphite) and CsH₂PO₂ (caesium hypophosphite) have been determined by single‐crystal X‐ray diffraction. The structures consist of layers of alkali cations and hypophosphite anions, with the latter bridging four cations within the same layer. The Rb and Cs hypophosphites are isomorphous.     

Electrochemical study of (NEt4)2Cl2FeS2MoS2 and (NEt4)2Cl2FeS2MoS2FeCl2

Summary The ability of [MoS₄]^2–, anions to be used as ligands for transition metal ions has been widely demonstrated, especially with Fe²⁺. The present study has been restricted to linear complexes such as (NEt₄)₂ [Cl₂FeS₂MoS₂] and (NEt₄)₂[Cl₂FeS₂MoS₂FeCl₂]. Their electrochemical properties are described: upon electrochemical reduction, these compounds yield MoS₂, as a black precipitate, and an iron complex in solution, assumed to be [SFeCl₂]^2–. The electrochemical reduction goes through two electron transfers, coupled with the breakdown of the molecular skeleton: a DISPl and an ECE mechanism. Depending on the solvent, the following equilibrium may be observed: [Cl₄Fe₂MoS₄]^2–[Cl₂FeMoS₄]^2–+FeCl₂. The equilibrium constant, K_D, was evaluated by differential pulse polarography. K_D is tightly related to the donor number of the solvent.     

Formal [(2+2)+2] and [(2+2)+(2+2)] nonconjugated dienediyne cascade cycloadditions

[reaction: see text] Fluoranthene 2 and heptacycle 3 are easily accessible from the reaction of diyne 1 and norbornadiene (NBD) in the presence of the rhodium catalyst. The unusual [(2+2)+(2+2)] adduct 3 was confirmed by the X-ray crystal structure analysis.     

Thermal decomposition of Me3SnO2PCl2, Me2Sn(O2PCl2)2 and Ph3SnO2PCl2

TG and DTA studies on Me₃SnO₂PCl₂, Me₂Sn(O₂PCl₂)₂ and Ph₃SnO₂PCl₂ were carried out under dynamic argon atmosphere. The results show that the decomposition proceeds in different stages leading to the formation of Sn₃(PO₄)₂ as a stable product. This compound was characterized by IR spectroscopy. Decomposition schemes involving reductive elimination reactions were proposed.     

The bivalent metal hypophosphites Sr(H2PO2)2, Pb(H2PO2)2 and Ba(H2PO2)2

The structures of isomorphous monoclinic strontium and lead bis­(di­hydrogenphosphate), Sr(H₂PO₂)₂ and Pb(H₂PO₂)₂, and orthorhombic barium bis­(di­hydrogen­phos­phate), Ba(H₂PO₂)₂, consist of layers of hypophosphite anions and metal cations exhibiting square antiprismatic coordination by O atoms. The Sr and Pb atoms are located on sites with point symmetry 2, and the Ba atoms are on sites with point symmetry 222. Within the layers, each anion bridges four metal cations.