一种可控纳米柱阵列的研制

在一次阳极氧化法制备多孔氧化铝(anodized aluminum oxide,AAO)的基础上,进行了二次、三次、四次氧化制备AAO,并对多次氧化制备多孔AAO的电流变化曲线和模板表面的形貌特点等进行了比较分析.二次、三次、四次氧化制备的AAO纳米孔孔径依次增大、孔间距减小,而模板表面的纳米孔有序性分布没有明显变化.控制一次氧化AAO模板的除膜时间,～10 min即可得到孔径规则、高度有序的AAO膜.最后,利用所制备的不同孔深和孔径的AAO为模板,通过热纳米压印复制技术制备了长度和直径等性质可控的PMMA纳米柱阵列. 关键词： 纳米柱阵列 聚甲基丙烯酸甲酯 多孔氧化铝模板 多次氧化法     

多孔氧化铝薄膜的制备和光学特性研究

采用阳极氧化法制备了二维有序纳米孔氧化铝膜.研究了工艺参数对多孔薄膜有序性、孔径、膜厚度等的影响，测量了多孔氧化铝有序膜的光透过、光吸收和光发射等光学特性.结果表明，在波长360 nm附近多孔氧化铝有序膜的光透过谱线和光吸收谱线发生突变，波长大于360 nm时，光透过增强；波长小于360 nm时，光吸收增强.多孔氧化铝有序膜的光致发光强度和峰位与激发光波长有关，光致发光谱范围在340~600 nm.     

高质量多孔氧化铝模板的制备

在草酸电解液中研究了阳极氧化法制备多孔氧化铝模板(AAO模板)。采用场发射扫描电子显微镜对多孔模板的形貌进行表征,结果表明:模板孔的分布均匀有序,孔径在40~70 nm;电解液浓度、氧化电压、氧化温度和氧化时间都会影响模板的形态;不经过高温退火及抛光也可以制得规则排布的多孔AAO模板。X射线衍射分析表明:氧化铝膜的主要成分为非晶态Al2O3。     

多孔氧化铝膜上自组织生长Sn纳米点阵列的研究

以多孔阳极氧化铝膜(porous anodic alumina, PAA)为基片，采用真空电子束蒸发的方法在多孔氧化铝膜上制备了高度有序度的Sn纳米点阵列.锡纳米点阵的XRD与块体锡的完全相同，扫描电镜(SEM)测试结果表明，所制备的金属Sn纳米点阵与阳极氧化铝膜的多孔阵列具有完全相同的有序结构，阵列中每个Sn纳米粒子的形状为球形的，其直径接近于PAA膜的孔直径.对Sn纳米点阵形成过程和形成机理进行了讨论.     

电子束蒸发法在多孔氧化铝膜上制备银纳米点阵列

采用二步阳极氧化法在草酸溶液中制备了高度有序的多孔阳极氧化铝(Porous Anodic Alumina,PAA)薄膜。以多孔氧化铝薄膜为模板,采用真空电子束蒸发的方法在多孔氧化铝模板上制备出了高度有序的金属银纳米点阵列体系。扫描电镜(SEM)测试结果表明,所制备的金属银纳米点阵列与多孔阳极氧化铝膜的多孔阵列具有完全相同的有序结构,阵列中银纳米颗粒的形状接近球形,其直径大约为70nm,与氧化铝模板的孔径基本一致。研究了高度有序银纳米点阵列的形成过程。     

用PAA模板法实现硅基纳米孔阵列结构

用二次阳极氧化方法制备出分立、双向贯通并且超薄（500—1000 nm）的多孔阳极氧化铝膜,贴合到硅片上进行干法刻蚀,实现图形转移,得到了硅基纳米孔阵列结构,并对工艺中影响图形转移质量的因素进行了探索.扫描电镜（SEM）测试结果表明该途径得到的纳米结构孔形态均匀且大面积有序,孔深度可达到125 nm.对该样品进行热氧化处理后进行光致发光（PL）测试,结果表明其光致发光机理是基于通常较微弱的TO声子辅助的硅带边发光,并实现了显著发光增强,对这种增强效果的物理机理进行了理论分析.该结构具有的独特光学特性为利用 关键词： 多孔阳极氧化铝模板 硅基纳米孔阵列结构 图形转移     

不同分枝结构多孔氧化铝膜的制备和光学特性

在阳极氧化铝的制备过程中,采用二次氧化方法,通过降低二次氧化过程中的电压,使之变为初始电压的1n,得到了具有n个分枝结构的纳米孔径的氧化铝膜.利用岛津UV3101分光光度计测试了样品的透射光谱与偏振光谱.结果表明,在可见和近红外波段,线型孔径结构的多孔铝膜比Y型和枝状结构的多孔铝膜具有更好的透射性能,在偏振性能方面也有优势,更适合作含金属微偏振器件的膜板材料.     

含钴阳极氧化铝膜的磁致偏光特性

用电化学法制备了高度有序的多孔阳极氧化铝模板,选用CoSO4溶液为电解液,用交流电化学沉积法在多孔阳极氧化铝的柱形微孔内制备含钴纳米线有序阵列.分别用扫描电镜(SEM)、X射线衍射仪对多孔阳极氧化铝模板和纳米线阵列的微观形貌和结构进行分析,结果显示阳极氧化铝膜内确有钴生成,且钴纳米线中的晶粒在生长过程中有(100)晶面...     

铝阳极氧化多孔膜制备及Eu3+组装

在草酸体系中,采用二次阳极氧化法可制备大面积有序铝阳极氧化多孔膜(AAO),用X射线粉末衍射(XRD)仪进行物相分析,利用扫描电子显微镜(SEM)表征多孔膜的形貌。研究表明,低温条件下制备的多孔膜孔径大小分布均匀,有序性好。微孔在膜的表面沿二维空间规则排列,具有一定的六方对称准周期性。孔道相互平行且与铝基底垂直。低温条件下,草酸体系中电解获得的AAO膜以无定形结构存在,经过800℃高温退火后转化为γ-Al2O3。通过水热反应法,获得了Eu^3 的铝阳极氧化多孔膜组装体(AAO：Eu^3 ),研究了组装体系的光谱特性。结果表明,这种方法制备的发光材料具有非常高的组装浓度,其发光具有很高的色纯度。     

罗丹明6G在银纳米线阵列上的SERS光谱研究

制备出有序、均匀的活性衬底一直足表面增强拉曼散射(SERS)研究中的关键.阳极氧化法制备的多孔氧化铝膜的结构有序、均匀,为纳米金属SERS基底的制备提供了模板.以沉积了银的多孔氧化铝组装体为衬底,研究了罗丹明6G(Rh6G)分子的表面增强拉曼散射光谱.结果表明,沉积了银的多孔氧化铝模板是很好的SERS衬底,Rh6G分子在此衬底上的SERS谱强度与银纳米线在表面的显露高度有关,而其拉曼频移未受表面状态的影响,而PO43-离子的存在使SERS强度得到很大提高.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.