13C-NMR研究丁二烯-异戊二烯共聚合的竞聚率和共聚物的序列分布

 用¹³C-NMR方法研完了不同配料比的丁二烯-异戊二烯本体共聚和溶液共聚物的结构,定量计算出了共聚物二元组的浓度和数均序列长度,采用T(?)DO″S法计算出了本体共聚和溶液共聚的竞聚率,并证明各种共聚产物的序列分布都服从一级Markov统计模型。     

AN/St悬浮共聚体系中AN在水/油两相间分配及其对共聚物组成的影响

研究了丙烯腈/苯乙烯(AN/St)悬浮共聚体系中AN在水/油两相间的分配及其对AN/St共聚物组成的影响.结果表明,AN分配于水/油两相间,使油相AN的含量低于相同单体配料比的本体聚合,导致生成的AN/St共聚物组成偏离本体共聚.为了准确预测进而控制AN/St悬浮共聚物的组成,提出了在考虑AN相分配的基础上计算AN/St悬浮共聚物组成的模型.计算结果与实验值一致,计算中用到的油相实际竞聚率与本体聚合相同,但该悬浮聚合的表观竞聚率随水/油比的变化而发生较大改变.     

丙烯酸甲酯/4-丙烯酰胺基-2,2,6,6-四甲基哌啶光共聚合体系的竞聚率和序列分布研究

以丙烯酸甲酯(MA,M1)和4-丙烯酰胺基-2,2,6,6-四甲基哌啶(AATP,M2)溶液光共聚合体系为研究对象,采用1H-NMR手段测定了MA/AATP共聚物的组成,用Mayo-Lewis积分法和扩展Kelen-Tüdos方法计算的竞聚率分别为0.88相似文献   

丙烯腈的共聚合及其竞聚率的研究

通过AN-MMA在本体以及在N,N-二甲基甲酰胺,二氧六圜、苯、环己烷、甲醇及水等溶剂中进行溶液共聚合的研究,得到以下结论: 1.证实了介质对一定共聚体系的均相溶液沉淀共聚合的竞聚率是有影响的。 2.提供了本共聚体系在多种介质中进行溶液共聚合时的竞聚率数据及有关的共聚物组成曲线。同时在水溶液共聚合中,证明柚口贞夫所报导的实验数据与事实不符。 3.根据实验结果,作者初步认为,在均相溶液沉淀共聚合反应中,共聚物组成所以发生变化可能是由于反应地点有效配比与单体投料配比出现差距所导致。而有效配比与两单体极性的差别以及介质与共聚物的极性大小有关。 4.在均相溶液沉淀共聚合中,尤其是采用非极性有机介质时,单体的绝对浓度对共聚物组成也有一定的影响。     

负载钛催化合成高反式丁二烯-异戊二烯共聚物的序列分布

采用TiCl4-MgCl2-Al(i-Bu)3体系催化丁二烯(Bd,M1)-异戊二烯(Ip,M2)共聚合成了高反式-1,4-结构的共聚物,用13^CNMR方法研究了共聚物的结构和组成分布,定量计算了共聚物二元组的浓度和数均序列长度,证明共聚物的序列分布服一级Markov模型,继而根据一张Markov模型预测了一次投料不同转化率下所得共聚物的链段分布。     

阴离子型共聚合反应产物分子链的序列结构

本文采用非稳态动力学方法研究了阴离子型共聚合反应产物的序列结构。经严格求解动力学微分方程组,推导出在恒定的共聚单体比条件下共聚物的序列分布函数、平均序列长度以及多元组浓度的解析表达式,并将这些结构参数与反应初始条件和时间联系起来,因而可根据聚合条件预测共聚物的微观结构。     

偏氯乙烯-丙烯腈悬浮共聚物的组成研究

研究了偏氯乙烯 丙烯腈 (VDC AN)悬浮共聚体系中AN的水溶性对单体相组成和树脂组成的影响 .结果表明 :由于AN部分地溶于水 ,使有机相AN的含量降低 ,导致共聚树脂的组成明显地不同于本体聚合模型的计算预测值 .为了准确地计算预测VDC AN共聚树脂的组成 ,本文假设溶于水的AN向有机相迁移的速度比聚合反应速度快得多 ,AN在两相的溶解分配近似为平衡态 .计算中先用描述AN在VDC/水系统中溶解分配的Marker式校正有机相AN的含量 ,然后根据校正后的AN含量用Mayo Lewis式计算预测VDC AN悬浮共聚物的组成 ,计算中有关的竞聚率值取自于文献中本体聚合的值 .计算结果与实验值一致     

丙烯腈/衣糠酸共聚行为的Monte Carlo模拟

建立了针对丙烯腈/衣糠酸共聚反应的Monte Carlo模拟算法,首先在不同pH值单体竞聚率条件下计算了共聚组成随单体投料比的变化,由实验结果验证了该Monte Carlo模型的准确性。在此基础上,对丙烯腈共聚物链结构的变化规律和影响因素进行了理论分析,指出传统一次性进料工艺中存在共聚物组成和序列结构均匀性差的问题,进而根据模拟计算结果提出调控共聚物序列结构均匀性的可行性方案。结果表明,通过在聚合不同阶段分时按比例补加活泼单体衣糠酸(ITA),可以对聚合产物的瞬时组成和序列结构起到有效的平均化效果,从而改善共聚组成和序列结构的均匀化程度,这种链结构的改进将有利于最终碳纤维性能的提高。     

环氧乙烷-环氧丙烷无规共聚醚链结构的核磁共振研究

本文用NMR波谱方法研究了无规共聚醚(EPO)的链结构。首先对EPO的~1H和~(13)CNMR谱进行了讨论。并从序列结构随环氧丙烷(PO)含量的改变,分析了EPO的二元组序列和三元组序列结构,从~(13)C实验谱中归纳出EPO的取代基参数(SCS),清楚地揭示了EPO的~(13)C谱,SCS参数和序列结构之间的关系,在此基础上计算了EPO系列共聚物的序列分布和数均序列长度。     

三氟化硼-乙醚络合物催化γ-戊内酯与ε-己内酯开环共聚的研究

以三氟化硼乙醚络合物为催化剂,进行了γ-戊内酯(γ-VL)与ε-己内酯(ε-CL)的本体开环共聚的研究.采用1H -NMR、13C- NMR证实了所得共聚物的结构,并对共聚物的分子量、组成、熔点等进行了表征.结果表明,在一定的条件下,难以均聚的γ-VL可与ε-CL发生共聚反应,从而在共聚物链结构中引入少量的γVL单元.γVL单元的引入使得共聚物的分子量和熔点下降.由K- T法估算出两种单体共聚的竞聚率分别为r(ε-CL)=17.6,r(γ-VL)=0.0078.     

TiCl_4/MgCl_2催化丙烯/1-辛烯共聚合研究

本文用TiCl_4/MgCl_2-Al(i-Bu)_3催化剂进行丙烯/1-辛烯共聚合,研究发现引入少量共聚单体1-辛烯时,能提高丙烯的聚合活性。30℃时,测得共聚合竟聚率为r_丙=5.63,r_辛=0.32。共聚物的结晶度和己烷不溶物含量随其1-辛烯含量的增加而迅速下降。X射线衍射及~(13)C-NMR测定结果表明,共聚物的己烷可溶部分为非结晶的无规共聚物,己烷不溶部分是具有镶嵌着半个1-辛烯单体单元的长嵌段聚丙烯链结构的结晶性共聚物。     

Calculation of Reactivity Ratios and Sequence Distributions in Copolymers from Monomers 13C-NMR Data

A screening procedure has been developed to predict the average sequence distribution in vinyl copolymers from monomer ¹³C-NMR data. The ¹³C-NMR absorption frequencies of the carbon atoms of the polymerizable double bond are used to calculate the Alfrey-Price Q and e values as previously described by Borchardt and Dalrymple. These, in turn, are used to calculate the monomer reactivity ratios. Reactivity ratios for 54 copolymerizations were calculated by this procedure and compared to literature values. The copolymer sequence distribution may then be determined by means of a computer program written by Harwood. The sequence distribution in copolymers of methacrylic acid and dimethyl-aminoethyl methacrylate, acrylonitrile and methyl methacrylate, 1,1-dichloroethylene and methacrylonitrile, ethyl acrylate and n-butyl methacrylate, and acrylamide and sodium 2-acrylamido-2-methylpropane sulfonate were calculated from reactivity ratios derived from ¹³C-NMR data and compared to literature values. This procedure may be used to calculate the reactivity ratios from ¹³C-NMR spectra of monomers for which no Q and e values are known. By this method the average sequence distribution of such monomers in copolymers may be predicted, significantly reducing the number of copolymers to be synthesized and tested for use in various applications.     

Synthesis and characterization of trans-1,4-butadiene/isoprene copolymers: Determination of sequence distribution and thermal properties

Two series of trans-1,4-poly(butadiene-co-isoprene) copolymers(TBIR) were prepared using the catalyst system Ti Cl4/Mg Cl2-Al(i-Bu)3 at different reaction temperatures. All dyad and triads sequence distributions, the number-average sequence length and the sequence concentration of the copolymers were calculated according to 13C-NMR spectra. The influences of temperature and initial molar ratio of butadiene to isoprene(Bd to Ip) on the distribution of the chain segments in the TBIR copolymers were discussed. The correlation of copolymer compositions and thermal properties were also evaluated, which facilitated the understanding of controlling the degree of crystallinity and the transition temperature by changing Bd content and temperature.     

用钛系载体高效催化剂进行乙烯-丙烯-1-丁烯三元共聚合的研究 Ⅱ.共聚物的结构表征

通过各种表征手段对用TiCl_4,Ti(OBu)_4/MgCl_2/EB/φSiCl_2/AlEt_3催化剂合成的乙丙丁三元共聚物进行了剖析。发现在一定组成范围内,三元共聚物不含庚烷不溶物。DSC和WAXD分析检测不到结晶相。用~(13)C-NMR技术表征了在相同条件下合成的乙丙、乙丁及丙丁三组二元共聚物的序列分布。结果表明,乙丙和乙丁共聚物的序列结构可用一级Markov分布描述。丙丁共聚物则服从Bernoulli分布,用~(13)C-NMR方法计算了乙丙丁三元共聚物的化学组成,并初步考察了共聚物硫化胶的力学性能。     

聚烯丙基氯化铵模板对AM/AA共聚物结构的影响

采用IR,1H-NMR和13C-NMR研究了聚烯丙基氯化铵(PAAC)模板对丙烯酰胺(AM)/丙烯酸(AA)共聚产物结构的影响,发现这种模板对共聚物P(AM/AA)序列结构和分子量有重要影响.由于共聚合体系中AA单体在PAAC模板聚合物上预组装,使得模板体系共聚物比无模板体系共聚物的AA和AM序列长度显著增加.这种类似多嵌段结构得到pKa′测定的进一步验证.另外模板分子量大小,模板和AA单体摩尔比,AM和AA摩尔比对共聚物结构的影响也进行了研究.应当指出这种模板聚合产物分离模板后仍有少量不能分离掉的PAAC聚合物存在.     

稀土催化丁二烯-异戊二烯共聚物的序列分布

用~(13)C-NMR方法研究了不同稀土元素聚合丁二烯-异戊二烯共聚物的序列分布。定量地求得丁-戊共聚物二元组分布及数均序列长度数据。证明以Nd、Pr及Ce为催化剂的共聚物分布较好地服从Bernoullian模型,以Y、Sm、Dy及Gd为催化剂的共聚物与Bernoullian分布有些偏离。     

Polymerization of coordinated monomers. XVIII. Sequence distribution in methyl acrylate–styrene copolymers prepared in the presence of zinc chloride

Methyl acrylate and styrene have been copolymerized in the presence of zinc chloride either by photoinitiation or spontaneously. The copolymerization mechanism is investigated by analyses of copolymers composition and monomer sequence distribution. The resulting copolymers are not always alternating, their composition being dependent especially on the monomer feed ratio. Appreciable deviation to higher methyl acrylate unit content from an equimolar composition occurs at monomer feed fractions of methyl acrylate over 0.7. The larger deviation is induced by higher temperature, by photoirradiation, and by greater dilution of the reaction mixture with toluene. The ¹³C-NMR spectrum of the alternating copolymer shows a sharp singlet at the carbonyl region, whereas the spectra of random copolymers prepared by benzoyl peroxide initiation at 60°C show a triplet splitting at the carbonyl carbon region, irrespective of copolymer composition. The relative intensities of the triplet peaks for the random copolymers are in good correspondence to the contents of triad sequences calculated by means of conventional radical copolymerization theory. These results clearly indicate that the carbonyl splitting is caused predominantly by variation of the monomer sequence and not by variation of the stereosequence. The monomer sequence distribution in the copolymers is thus directly and quantitatively measured from the split carbonyl resonance. Although the same triplet splitting appears in the spectra of methyl acrylate–rich copolymers prepared in the presence of zinc chloride at high feed ratios (>0.7) of methyl acrylate, the relative intensities of the split peaks do not fit the sequence distributions of random copolymers calculated by means of the Lewis–Mayo equation. The copolymerization yielding these peculiar sequences and the alternating sequence in the presence of zinc chloride is fully comprehended by a copolymerization mechanism proceeding between two active coordinated monomers, i.e., the ternary molecular complex composed of zinc chloride, methyl methacrylate, and styrene, and the binary molecular complex composed of zinc chloride and methyl methacrylate.     

Acrylonitrile–4-vinylpyridine copolymers effect of comonomer sequence distribution on properties

Acrylonitrile–,4-vinylpyridine copolymers were prepared in chloroform solution at 60°C with AIBN as initiator. Copolymer compositions were determined from their 15.01-MHz ¹³C-NMR spectra. Reactivity ratios of r_AN = 0.093 and r_4VP = 0.32 were calculated by the Kelen and Tudos method. The run number, number-average sequence lengths, and monomer sequence distributions were also calculated. The T_g values of the copolymers, their dye uptake, and degree of alkaline hydrolysis were influenced by the overall copolymer composition but particularly by the monomer sequence distribution in the copolymers.