X射线荧光光谱法测定萤石中氟化钙

采用X射线荧光光谱仪可以快速准确测定萤石中总钙的含量.但测定其中氟化钙含量时,一方面,由于样品中碳酸钙计入钙量,从而造成氟化钙测定结果准确性较差.另一方面,铜、锌等金属元素在熔融制样时对铂金坩埚腐蚀较大,因此需要进行酸处理除去碳酸钙及铜、锌等金属元素.然而,样品经过酸处理后,质量会发生变化,造成熔剂与样品的比例不一致,从而影响测定结果.对样品前处理条件、XRF分析中熔片和仪器工作条件等进行了优化,建立了熔融制样、X射线荧光光谱法（XRF）准确测定萤石中氟化钙含量的方法.方法干扰少,具有良好的准确度和精密度,操作简单,提高了分析效率.     

浅析铝土矿烧失量的差异在X-射线荧光光谱(XRF)分析中造成的影响

探讨了一水铝土矿与三水铝土矿烧失量的差异在X-射线荧光光谱(XRF)分析中造成的影响。采用实验的方式考察了硼酸锂熔融制样过程中铝土矿的烧失量损失情况,实验表明,在熔融过程中,烧失量越大的样品质量损失也越多。运用理论计算分析了烧失量损失对测定结果的影响,结果表明:当采用一水铝土矿绘制工作曲线测定三水铝土矿样品时,将导致三水铝土矿中各组分测定结果偏高;烧失量的差异对主量元素测定结果影响较大,而对微量元素测定结果影响较小;待测物质的烧失量与基准物质烧失量差异越大,测定结果的偏差也就越大。     

熔融制样-波长色散X射线荧光光谱法测定铁矿石中12种主次成分

采用熔融制样法对铁矿石进行熔融制样;以三氧化二钴(Co2O3)作为铁的内标,并对熔剂、氧化剂、脱模剂、熔融温度和熔融比例进行了讨论。采用理论α系数法、经验系数法校正基体效应和各元素的谱线重叠干扰。建立了波长色散X射线荧光光谱(WDXRF)测定铁矿石中12种组分的分析方法。本法测定铁矿标准物质(GBW07822-GBW07830)各组分的相对标准偏差(RSD)在0.41%~4.2%之间,测定值与标准值相符,且与电感耦合等离子发射光谱的对比测定结果一致。利用本法对实际铁矿样品的全铁含量进行测定,结果与化学分析法的测定结果基本一致。     

熔片制样-X射线荧光光谱法同时测定石灰石及白云石中主、次、微量成分

采用熔融制样,以四硼酸锂-偏硼酸锂混合熔剂(12:22)作为熔样体系,硝酸锂和碘化铵分别作为氧化剂和脱模剂,建立了石灰石及白云石中Ca,M g,Al,Fe,K,M n,Na,Si,Ti,P,S等11种元素的熔片制样-波长色散X射线荧光光谱法。选择石灰石、白云石有证标准物质及碳酸钙基准物质,并将其按一定比例人工配制成系列标样,建立了检测的校准样品体系。采用较大的稀释比与未知烧失量校正相结合的办法,无需对样品烧失量进行校正,简化了分析步骤。应用变化的理论α系数法校正,有效克服基体效应的影响。精密度实验表明,各组分测定结果的相对标准偏差在0.22%~9.0%(n=11)之间。选择石灰石和白云石标准物质进行准确度实验,测试结果与标示值一致。     

浅析铝土矿烧失量的差异在X-射线荧光光谱分析中造成的影响刘静,马慧侠,彭展,白万里

本文探讨了一水铝土矿与三水铝土矿烧失量的差异在X-射线荧光光谱分析中造成的影响。采用试验的方式考察了硼酸锂熔融制样过程中铝土矿的烧失量损失情况;运用理论计算分析了烧失量的损失对测量结果的影响。试验与理论分析结果表明：当采用一水铝土矿绘制工作曲线来测量三水铝土矿样品时,将导致三水铝土矿中各组分测量结果偏高;烧失量的差异对主量元素测量结果影响较大,而对微量元素测量结果影响较小;待测物质的烧失量与基准物质烧失量差异越大,测量结果的偏差也就越大。     

X射线荧光光谱法测定除尘灰中砷、铅含量

以熔融制样法,采用X射线荧光光谱对除尘灰中的有害元素：砷、铅含量进行了测定。对样品的烧失温度进行了讨论,发现在950℃灼烧温度下灼烧2h时除碳完全。砷和铅的相对标准偏差为0.15 %和0.20 %。测试结果与化学分析法、原子吸收光谱法等相吻合。该方法制作工艺简单,分析速度快,样品可长期保存,还能满足其他元素的日常分析。     

X射线荧光光谱法测定钒铁合金中主次元素含量

用熔融制样法将钒铁合金样品在铂金坩埚中与四硼酸锂和偏硼酸锂熔融,熔体在铂金坩埚中自动成型,用X射线荧光光谱法测定钒铁合金中钒、硅、锰、铝和磷等主次元素含量。经试验求得熔融时,四硼酸锂、混合溶剂(四硼酸锂∶偏硼酸锂=67∶33)和样品的最佳质量比为30比5比1。各元素的检出限在12.4～51.2μg.g-1之间。方法用于标准样品分析,测定值与认定值相符。     

X射线荧光光谱法同时测定锰锌铁氧体材料的主量组分

用熔融制样法将样品在铂金坩埚中与四硼酸锂熔融,熔体倒入铂金专用模具中成型为玻璃态块样。用X射线荧光光谱法测定锰锌铁氧体样品中氧化铁、四氧化三锰及氧化锌含量。经试验求得熔融时样品和无水四硼酸锂熔剂的最佳质量比为1比17.5。采用基体参数法和理论α系数法对基体效应及谱线重叠的干扰予以校正。此法用于锰锌铁氧体材料分析,3种组分的日间和日内相对标准偏差(n=7)分别小于3.5%和4.0%;用于标准样品的分析,3种组分的测定值与标准值之间的绝对误差在-0.15%~0.02%之间。     

X射线荧光光谱法分析镁砂的主次成分

采用镁砂标准样品作为校准样品,建立了熔融制样X射线荧光光谱法测定镁砂中MgO,Al2O3,SiO2,CaO,P2O5,Fe2O3的方法。采用熔融法为样品片和校准片的制备方法,选择四硼酸锂-偏硼酸锂（67＋33）为助熔剂,1.00mL LiBr溶液为脱模剂,熔融温度为1 100℃,熔融时间20min。对镁砂样品测定的相对标准偏差（RSD）小于3%,对不同镁砂标准样品进行测定,方法的测定结果与认证值相吻合。     

X射线荧光光谱法分析镁砂中的主次成分

采用镁砂标准样品作为校准样品,建立了熔融制样X射线荧光光谱法测定镁砂中MgO,Al2O3,SiO2,CaO,P2O5,Fe2O3的方法。采用熔融法为样品片和校准片的制备方法,选择四硼酸锂-偏硼酸锂(67+33)为助熔剂,1.00mL LiBr溶液为脱模剂,熔融温度为1 100℃,熔融时间20min。对镁砂样品测定的相对标准偏差(RSD)小于3%,对不同镁砂标准样品进行测定,方法的测定结果与认证值相吻合。     

助熔剂对煤焦高温气化反应性的影响

研究了平顶山十二矿高灰熔点煤灰分别添加助熔剂(氧化钙和三氧化二铁)后灰熔点的变化规律，并考察了1 300 ℃～1 550 ℃范围内适宜助熔剂添加量下煤焦的气化反应性变化规律。实验表明：以灰的流动温度（t3）为选择依据，十二矿煤助熔剂氧化钙、三氧化二铁的适宜添加量相应为：3%～7%和5%～10%；助熔剂添加量对煤焦气化反应性的影响与气化温度密切相关。较低气化温度时，煤焦的气化反应性随添加量的增加而提高，但随温度的提高，助熔剂添加量对煤焦反应性的影响逐渐减弱，温度升至1 550 ℃时，助熔剂的影响几乎消失。助熔剂在高温下的熔融、团聚导致其在煤焦中分散性的改变，从而使助熔剂在较低温度下具有的催化作用很快消失，这可能是高气化温度下煤焦气化反应性不受助熔剂影响的最重要原因之一。     

Phase separation in styrenated polyester resin containing a PVAc low profile additive and metallic stearates

Unsaturated Polyester Resins(UP) that contain compatible low‐profile additives (PVAc) are used in BMC composite materials (Bulk Molding Compound). The general morphology of the UP/PVAc matrix is made up of small polyester nodules embedded in a matrix‐rich thermoplastic additives. An internal mold‐release agent (often a Calcium Stearate) is incorporated into the UP/PVAc mixture to facilitate the extraction of the curing materials. Although used in small quantity, this agent does have an effect on the final morphology of the curing mixture. Some of the internal mould‐release agents provoke the formation of a polyester rich phase in the form of large spherical globules (roughly 60 micrometers). The formation of the “globular” polyester phase seems to depend largely on the nature of the metallic ion and the solubility (in the styrene) of the mould‐release agent. If this phase occurs, most of the internal mould‐release agents are trapped inside the polyester globules. Given its particular affinity for mineral materials, this phase tends to coat filler and glass fibbers. Consequently, this phase strongly conditions the mechanical characteristics of the final composite.     

Scanning Electron Microscopy Investigation for Monitoring the Emulsion Deteriorative Process and Its Applications in Site-Directed Reaction with Paper Fabric

The O/W isocyanate emulsion can be used as a sizing agent to improve the waterproof performance of paper. However, the -NCO content in the emulsion diminishes with the prolongation of standing time. What is happening to this seemingly stable emulsion, especially concerning its microstructure evolution? We propose to monitor the emulsions deteriorative process by combining freeze-drying technique and SEM. Thus, the emulsion containing -NCO active group was obtained by the synthetic polymer emulsification of HDI trimers. The results of SEM demonstrate that the emulsion deteriorative process actually represents the collapsing and fusion of stable honeycomb structure with the prolongation of standing time and increasing temperature. This is possibly due to the fact that the inner aggregative HDI trimers are reacting with outside water to form urethane macromolecules, and this results in the collapsing and fusion of the honeycomb structure, as observed in SEM images. Moreover, the measurement results of -NCO content and FT-IR spectroscopy present the -NCO content as reducing with increasing standing time and temperature. This conclusion further proves our hypotheses. Additionally, the emulsions are used to treat the paper by site-directed reaction. The results show that the with the increase of the standing time and temperature, the contact angles and surface free energy show a decrease and an increase, respectively, whereas surface free energy appeared at a minimum of 29.19 mJ·m⁻² when the standing time and temperature was 1 h and 25 °C.     

左旋甲基多巴分子印迹纳米给药系统的合成、表征及药物缓释研究

采用沉淀聚合法合成了左旋甲基多巴(L-Methyldopa, LMD)分子印迹聚合物微球(MIPMs), 并对其合成条件进行了详细研究. 结果表明, 聚合温度和引发剂的用量对微球的大小和形态有较大的影响, 微球的粒径随聚合温度的降低而增大, 随偶氮二异丁睛(AIBN)量的增大而增大. 而模板分子似乎对微球粒径的影响不是很明显. 通过扫描电镜、静态吸附试验(BET)和斯卡查德分析(Scatchard analysis)、红外光谱分析和模拟人体胃液扩散实验等对微球的外貌形态、吸附性能、分子印迹效果和药物缓释效果进行了表征. BET吸附实验和Scatchard 分析结果表明, 分子印迹聚合微球(MIPMs)的最大静态吸附量是非印迹聚合物微球(NIPMs)的3倍. 药物扩散实验表明, LMD在非印迹微球(NIPMs)上的释药率几乎与时间呈直线关系, 说明其释药过程完全受扩散控制; 而LMD在MIPMs上的释药率则呈曲线上升趋势, 说明其释药过程除了受扩散控制外, 还受到药物模板分子与MIPMs之间的印迹效应的协同作用的控制, 从而达到了缓释药物分子的目的. 实验结果表明, 在模拟胃液中, MIPMs释放药物的持续时间(10 h)是NIPMs持续时间(5 h)的2倍, 表明分子印迹微微球确实具有缓释药物的效果. 因此, MIPMs有望进一步应用于LMD药物缓释系统的研究.     

Optimisation of mould surface temperature and bottle residence time in mould for the carbonated soft drink PET containers

Polyethylene terephthalate (PET) bottles, which are usually produced by injection stretch blow moulding (ISBM) are widely used for carbonated soft drinks (CSD) storage and transportation. Stretch rod movement, blow pressure, preform temperature profile, mould surface temperature and material properties are among the most important factors affecting the final product's quality in terms of the thickness distribution, burst pressure and top-load resistance of the bottles. However, the residence time of the blown bottle inside the mould is also an important factor affecting its final properties. Especially in PET bottle production for hot fillings, the residence time is a very important factor because the longer the residence time the better the crystalline structure of the PET. In this production, the lid section is desired to have a fully crystalline form so that it can withstand hot fluids. In this study, the aim was to optimise the mould surface temperature and the blown bottle's residence time inside the mould for 1 L soft drink PET bottle production based on the final properties using the ECHIP 7 design of experiment (DOE) program. The method employed through this program was a quadratic one. Optimum process parameters were determined by the response surface method (RSM) and the process settings ensuring maximum top-load, burst pressure, Tg and degree of crystallinity were regarded to be optimum. It was found that the optimum mould surface temperature and blown bottle residence time inside the mould were 10 °C and 20 s, respectively.     

Hydrogel containing L-valine residues as a platform for cisplatin chemotherapy

Two acrylic hydrogels, of low cross-linking content and carrying the L-valine residues, were synthesized and studied as a platform to load and release the chemotherapeutic agent cisplatin. The platinum(II)-complex species showed a well-defined stoichiometric ratio in which two carboxylate groups of the collapsing gel coordinate a metal center; this was confirmed by FT-IR spectra. When loaded in water, a zero-order release rate of platinum(II)-species was shown in the physiologic solution (PBS, pH 7.40) for more than one week. Moreover, the amount of platinum(II)-species released from the hydrogel may be improved either by the cross-linking degree and by the temperature. Any increase of the cross-links results in a decreased slope of the straightline Pt(II)/gel (mg/g) versus time, whereas the increasing temperature results in a greater amount of platinum(II)-species in solution. The chemical- and swelling-controlled release are the main mechanisms supervising the whole release process. On the other hand, the loading of cisplatin and temsirolimus in DMF showed a characteristic two phase releasing pattern; the initial burst effect was always followed by the zero-order release rate for a week. In this case only a swelling-controlled mechanism was mainly invoked. The cytotoxic activity towards Me665/2/21 human melanoma cell line, afforded by the cisplatin-loaded hydrogel, was close and in some cases higher compared to the native cisplatin at the same concentration; an interesting synergy in term of cytotoxicity was observed when a combined treatment of temsirolimus and cisplatin was used, although temsirolimus exerted only a moderate inhibition of cell proliferation.     

pH and ionic sensitive chitosan/carboxymethyl chitosan IPN complex films for the controlled release of coenzyme A

pH and ionic sensitive interpenetrating polymer network (IPN) complex films based on chitosan (CS) and carboxymethyl chitosan (CM-CS) were prepared by using glutaraldehyde as crosslinking agent. Its structure was characterized by FT-IR, which indicated that the IPN was formed. The films were studied by swelling, weight loss with time, and release of coenzyme A (CoA). It was found that the IPN films were sensitive to pH and ionic strength of the medium. The cumulative release rate of CoA decreased with CoA loading content, ionic strength or crosslinking agent increasing. The composition of the IPN films and pH of release medium also had significant effect on the release of CoA. The differences in the rates and amounts of released CoA may be attributed to the swelling behavior, the degradation of films, and interaction between drug molecule and polymer matrix. These results suggested CS/CM-CS IPN films could be used as drug delivery carrier.     

准东煤掺烧高岭土对固钠率及灰熔融特性影响研究

选择常见的黏土矿物高岭土作为准东煤添加剂掺烧,研究了不同掺混比例、不同燃烧温度下添加剂的固钠率和煤灰熔融特性的变化,结合XRD谱图和三元相图研究了灰中矿物在高温下的演变过程。结果表明,固钠率随高岭土掺混比例增加逐渐增大,在0~2%时增长较快,2%~5%增长较慢,随燃烧温度升高略微下降;掺混后煤灰熔点随掺混比例先缓慢减小,再快速减小,后快速增加,在3%时达到1 200 ℃左右;XRD和三元相图分析结果表明,煤灰熔融特性变化是由于灰中硅钙石、钙黄长石和钙长石矿物比例的变化引起,发生低温共熔现象是导致掺混比例为3%和4%时煤灰熔点最低的主要原因;当掺混比例为2%时,固钠率在60%以上且灰熔点在1 300 ℃左右,利于固态排渣,当掺混比例为3.0%~4.0%时,灰熔点在1 200 ℃左右,利于液体排渣。     

Synthesis of three-dimensional hydrogels based on poly(glycidyl methacrylate-alt-maleic anhydride): Characterization and study of furosemide drug release

In the present work, three-dimensional drug carriers were synthesized via chemical modification of poly (glycidyl methacrylate-alt-maleic anhydride) P(GMA-alt-MA) by isopropylamine (IPA) and ethylenediamine (EDA) with different molar ratios. Then furosemide drug (FR) was loaded on the hydrogels and studied for its slow release in phosphate-buffered saline (PBS) solution (pH = 7.41) at 37 °C. According to the obtained results, the sample with the lowest amount of crosslinking agent (Sample A) showed the highest swelling ratio in comparison to the others. By increasing the rigidity of carrier in the result of increasing the crosslinker density, the amount of the released drug was decreased. However, the release rate for all of samples (slope of the profiles) were rather similar. All the synthesized carriers have shown pH dependent properties and the maximum release rate was shown in basic pH. Also, the drug release experiments in different temperatures showed almost thermal sensitivity properties for synthesized carriers and release rate become faster by increasing the medium temperature. The FT-IR, TGA, and FE-SEM analyses were carried out for characterization of prepared samples and the swelling behavior of prepared hydrogels were measured too. Investigation of the release data with different mathematical models showed the highest adaption with the Higuchi model for all samples.