双道氢化物发生-原子荧光光谱法同时测定核电用钢中痕量砷和锑

建立了双道氢化物发生-原子荧光光谱法同时测定核电用钢中痕量砷和锑的新方法。用王水溶解样品,以2.0 g/L L-半胱氨酸溶液作为预还原剂,在低酸度条件下实现对砷、锑的预还原。用20 g/L硼氢化钾溶液作为还原剂,氢化物发生反应在0.5 mol/L乙酸介质中进行。砷、锑的质量浓度在40μg/L范围与相应的荧光强度呈线性关系,方法的检出限(3s/k)分别为0.032μg/L和0.022μg/L。应用此方法同时测定了核电用钢及不锈钢标准样品中的砷锑含量,并与电感耦合等离子体原子发射光谱法的分析结果作了对比,测定值与标准样品的标准值相符,结果的相对标准偏差(n=8)均小于5.0%。     

氢化物发生–原子吸收光谱法测定铅粉中痕量砷、锑

建立氢化物发生–原子吸收光谱法联用测定铅粉中痕量砷、锑的方法。试样用稀硝酸溶解,用5%抗坏血酸溶液作为砷(Ⅴ)、锑(Ⅴ)的预还原剂,5%的硫脲溶液作为其它元素的掩蔽剂,选用1%硼氢化钠溶液作为还原剂,氢化物反应在10%盐酸介质中进行。在优化的试验条件下,砷、锑的质量浓度在0~20 ng/m L范围内与吸光度线性相关,相关系数r2分别为砷0.999 6,锑0.993 8,方法的检出限分别为砷0.40 ng/m L,锑0.75 ng/m L。砷、锑测定结果的相对标准偏差分别为4.96%,6.27%(n=6),铅粉样品加标回收率分别为砷87.6%,锑79.3%。该方法准确可靠,可用于测定铅粉中痕量砷、锑。     

电感耦合等离子体发射光谱法测定粗二氧化碲中 铜、铅、锑、铋、砷和硒

粗二氧化碲作为碲精炼或碲化工产品生产的重要原料,其中共存元素铜、铅、砷、锑、铋、硒含量的准确测定对于生产过程质量控制和贸易结算具有重要意义,但目前没有粗二氧化碲中铜、铅、砷、锑、铋、硒含量检测的标准分析方法。采用王水和饱和氟化氢铵分解试样,在王水和酒石酸介质中,选用Cu 327.393 nm、Pb 220.353 nm、Sb 217.582 nm、Bi 223.061 nm、As 193.696 nm、Se 196.026 nm为分析谱线,采用电感耦合等离子体发射光谱(ICP-AES)法测定粗二氧化碲中铜、铅、锑、铋、砷和硒含量。各元素校准曲线的相关系数均大于0.999;铜、铅、锑、铋、砷和硒的检出限分别为0.0004%、0.0005%、0.0006%、0.0007%、0.0004%和0.0007%,定量检出限分别为0.0012%、0.0016%、0.0020%、0.0025%、0.0013%和0.0025%。按照实验方法测定5个粗二氧化碲样品中铜、铅、锑、铋、砷和硒,测定结果的相对标准偏差(RSD,n=7)为0.79%~4.8%,加标回收率为96.0%~103%。方法简单,精密度和准确度较高,可用于测定粗二氧化碲中铜、铅、砷、锑、铋、硒含量。     

蒸气发生–原子荧光法连续测定化探样品中微量砷、锑、铋、汞、硒、碲

建立了连续测定化探样品中微量砷、锑、铋、汞、硒、碲的原子荧光光谱法。研究了酸度、KBH4溶液浓度、基体改进剂等条件对荧光强度的影响。在优化的实验条件下,砷、锑、铋、汞、硒、碲的检出限分别为0.011,0.006,0.020,0.002 5,0.005,0.002 mg/L,测定结果的相对标准偏差分别为1.30%,4.64%,3.76%,5.46%,2.04%,3.41%(n=11),准确度大于98%。该方法简便,成本低,检测结果准确,检出限、准确度及精密度均能达到行业规范要求,可用于化探样品中微量元素测试。     

氢化物发生–原子荧光光谱法同时测定锌锭中砷和锑

建立用氢化物发生–原子荧光光度计同时测定锌锭样品中砷和锑含量的方法。采用硝酸一次溶样,加入酒石酸防止锑水解。加入硫脲–抗坏血酸混合溶液作为还原剂和掩蔽剂,消除干扰元素的影响,对实验条件进行了优化。砷和锑的负高压分别为220,200 V,灯电流分别为80,60 mA,还原剂为1%硼氢化钾溶液(含0.5%KOH),载流为10%盐酸溶液,还原时间为30 min。测定砷的线性范围为0~80 ng/mL,相关系数r=0.999 8,检出限为0.35μg/L,测定结果的相对标准偏差为3.18%(n=11);测定锑的线性范围为0~80 ng/mL,相关系数r=0.999 6,检出限为0.42μg/L,测定结果的相对标准偏差为4.32%(n=11),砷和锑的加标回收率在97.46%~100.30%之间。用该方法对标准样品进行测定,测定结果与标准值相符。该方法基体干扰少,灵敏度高,适合于锌锭中砷和锑的日常测定。     

电感耦合等离子体质谱法测定地球化学样品中的银、砷、锑、铋

建立了王水分解样品,电感耦合等离子体质谱法测定地球化学样品中的银、砷、锑、铋的方法,采用王水-水浴分解试样,电感耦合等离子体质谱仪测定新疆和田策勒恰哈地球化学样品中的银、砷、锑、铋,确立了最佳的溶样时间、测定酸度、干扰元素的校正方法,结果令人满意。各元素的方法检出限为0.003 8~0.041g/g;相对标准偏差RSD(n=12)为0.52%~2.8%;方法灵敏度较好、简便、快速,且结果准确,适用于大批量地球化学样品的快速测定。     

氢化物发生原子荧光法测定畜禽粪便中砷和汞

通过王水系统对畜禽粪便中砷、汞元素进行了提取,利用原子荧光光谱仪同时测定了畜禽粪便中的砷、汞,并对灯电流、负高压、载气流量等检测条件进行了优化。结果表明,用王水对畜禽粪便中的砷、汞前处理,可同时测定样品中的砷、汞。砷、汞检出限分别为0.051 5、0.009 6μg·L1。该法快速简便,回收率好,砷的回收率为91.9%～103.0%,汞的回收率为93.9%～101.5%。该法精密度高、结果准确,砷、汞的最大标准偏差分别为4.03%、4.47%,完全适用于畜禽粪便中砷、汞的检测。     

ICP-AES法测定粗氧锑中砷硒

３用浓硫酸溶解粗氧锑,ＩＣＰ－ＡＥＳ法直接测定砷。对于样品中的痕量硒,先以次磷酸钠还原单质,并与砷共沉淀,经浮选分离后再测定。对硒的分离条件进行了优化。考察了基体锑的干扰及共存杂质的影响。方法运用于粗氧锑样品中砷、硒测定、结果满意。     

微波王水消解不赶酸原子荧光光谱法测定土壤中的砷

采用微波消解土壤样品不赶酸的情况下利用原子荧光光谱法测定土壤中的砷.结果表明:微波王水消解土壤样品不赶酸情况下,砷的测定值均在国家标准物质ESS-1的推荐值范围内.砷的线性范围分别为0.0～50.0μg/L,相关系数为r=0.9995.按称取0.2 g样品,定容至50 mL,求出砷检出限为0.5 mg/kg.砷回收率为93.4%～100.9%之间,相对标准偏差(n=4)为0.39～4.56%.结果表明:微波王水消解不赶酸原子荧光光谱法测定土壤中的砷,灵敏度高,操作简便快速,结果准确可靠.     

电感耦合等离子体质谱法(ICP-MS)测定纯金中的13种杂质元素

提出了使用电感耦合等离子体质谱法同时测定纯金中银、铜、铁、铅、锑、铋、钯、镁、锡、镍、锰、铬、砷13种杂质元素的分析方法。采用王水处理样品,以铑作为内标元素,不用分离基体,以王水作为测定介质,在最佳的仪器工作条件下直接测定。铁、铜、铅、锑、铋、钯、银、镍、镁、砷、锡、锰、铬的检出限分别为:1.80,0.86,1.23,0.90,0.26,0.39,1.05,0.33,1.61,2.30,1.15,1.05,0.89ng/mL,回收率在98.6%～102.8%,相对标准偏差(RSD,n=6)为1.0%～3.0%。方法具有灵敏度高、检出限低、干扰少、不用分离基体、分析速度快、能够进行多元素同时分析等特点,特别适合于生产企业的质量控制分析。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.