薄层色谱扫描法测定塑料食品袋中酞酸酯的含量

建立了采用薄层色谱扫描测定塑料食品袋中4种酞酸酯(酞酸二甲酯(DMP)、酞酸二乙酯(DEP)、酞酸二丁酯(DBP)和酞酸二(2-乙基己基)酯(DEHP))的方法。经粉碎的样品先用乙醇浸泡24 h,然后超声提取,经0.45 μm滤膜过滤。点样在以丙酮处理过的硅胶G板上,以乙酸乙酯-无水乙醚-异辛烷(体积比为1∶4∶15)为展开剂展开,以双波长反射吸收飞点扫描测定(λS=275 nm,λR=340 nm),外标法定量。该法的线性关系较好,DMP、DEP、DBP和DEHP的检出限分别为2.1,2.4,3.4和4.0 ng,混合标准品在同一薄层板上的峰面积的相对标准偏差（RSD）为2.8%～3.5%,4种酞酸酯的样品加标回收率为78.58%～111.04%。该方法样品用量少,前处理简单,分离效果好,可用于塑料袋中4种酞酸酯的同时测定。经与气相色谱法的分析结果比较,两种方法对实际样品的分析结果接近。     

GC-MS测定人血清中酞酸酯类环境污染物

为了解酞酸酯类环境污染物在人血清中的含量水平。采用毛细管柱气相色谱-质谱联用法的选择离子检测(GC-MS-SIR)技术,结合有机溶剂提取,高速离心去蛋白和低温浓缩的方法测定103份健康人血清中酞酸二丁酯(di--nbutyl phthalate,DBP)和酞酸二异辛酯[di-(2-ethyl-hexyl)phthalate,DEHP]。测定结果提示酞酸酯类环境污染物已进入人血清,DBP约为7.10 mg.L-1,DEHP约为6.78 mg.L-1,大部分人体内已有一定的污染负荷。     

环境样品酞酸酯分析中溶剂背景的影响

选择环境样品酞酸酯分析中常用的有机溶剂,通过GC-MS对浓缩后的色谱纯、分析纯以及分析纯经过重蒸处理的有机溶剂进行11种酞酸酯背景测定。结果表明这些常用有机溶剂存在一定程度的酞酸酯污染,特别是邻苯二甲酸二正丁酯(DBP)和邻苯二甲酸二(2-乙基)己酯(DEHP)等2种环境样品中常见酞酸酯污染单体,最高浓度可达74.2μg/L(DBP)和64.3μg/L(DEHP)。有机溶剂用量大的酞酸酯分析方法(如土壤提取)需要对提取剂背景进行严格控制。     

高效液相色谱二极管阵列检测器测定化妆品中的6种酞酸酯

建立了用高效液相色谱二极管阵列检测器测定化妆品中6种酞酸酯——邻苯二甲酸二甲酯(DMP)、二乙酯(DEP)、二丁酯(DBP)、丁基苄基酯(BBP)、二(2-乙基己)酯(DEHP)和二正辛酯(DOP)的方法一样品用甲醇超声提取．高速冷冻离心,经0．5μm滤膜过滤．直接注入高效液相色谱．在280nm波长进行分析用保留时间结合酞酸酯紫外光谱定性．外标法定量该法的回收率为85％～110％．精密度RSD为0．058％～2．84％．检出限：DMP．DEP、BBP和DBP均为5ng．DEHP和DOP为10ng,该方法准确度和灵敏度高．样品用量少．前处理简单。可同时测定化妆品中6种酞酸酯化合物。     

胶束电动毛细管色谱测定塑料食品包装袋中邻苯二甲酸酯类化合物的研究

采用胶束电动毛细管色谱法对5种邻苯二甲酸酯类化合物(邻苯二甲酸二甲酯(DMP)、邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二丁酯(DBP)、邻苯二甲酸二(2-乙基己基)酯(DEHP))和邻苯二甲酸二正辛酯(DOP))进行了分离研究,考察了溶液的pH值、胶束浓度和有机改性剂等对分离的影响。结果表明:以5 mmol/L硼砂-25 mmol/L十二烷基硫酸钠(SDS)-15%(体积分数)甲醇溶液为电泳缓冲液(pH 9.2),采用压力进样方式,25 kV恒压下进行分离,在波长200 nm处检测,各组分在17 min内可达到基线分离。DMP、DEP、DBP、DEHP和DOP的检出限分别为0.13 mg/L、0.14 mg/L、0.38 mg/L0、.13 mg/L和0.10 mg/L。本法应用于塑料食品袋中邻苯二甲酸酯类化合物的测定,回收率范围为81.80%~118.87%,峰面积的相对标准偏差(RSD)小于4.30%(n=10),测定结果满意。     

仿真饰品中邻苯二甲酸酯类增塑剂的含量测定和迁移风险考察

建立了仿真饰品中14种邻苯二甲酸酯类增塑剂的含量和迁移量测定的气相色谱-质谱(GC-MS)检测方法。考察了微波萃取、超声波萃取、快速溶剂萃取和索氏提取4种前处理方法对增塑剂含量测定的影响。在模拟人体温度及汗液环境下,考察了0～168 h内塑料仿真饰品中邻苯二甲酸二丁酯(DBP)、邻苯二甲酸二(2-乙基己基)酯(DEHP)和邻苯二甲酸二辛酯(DOP)3种增塑剂的迁移风险。结果表明微波萃取法的提取效率优于其余3种方法。所建立方法的定量限为5 mg/kg (邻苯二甲酸二异壬酯(DINP)、邻苯二甲酸二异癸酯(DIDP)为25 mg/kg),在0.1～50 mg/L(DINP、DIDP在0.5～250 mg/L)范围内,线性相关系数在0.99以上,在3个添加水平下的回收率在90.95%与98.67%之间。在模拟条件下,DEHP的迁移风险较高,浸泡72 h后约有0.75%溶出,而DBP和DOP的溶出风险较低。该法的灵敏度高、回收率高、选择性好,能满足实际工作的要求。     

高效液相色谱法测定塑料袋装食品中的邻苯二甲酸酯

采用高效液相色谱法测定用塑料袋盛装的食品中的邻苯二甲酸酯(PAEs),供试的食品为馒头、油饼、黄瓜和番茄.用同种塑料食品袋与纸袋分别盛装30 min,进行高速分散后超声波提取15 min,经弗罗里硅土层析柱净化,后用高效液相色谱进行分析,外标法定量.该方法的加标回收率为82.7%～107.6%,RSD为1.4%～6.9%,检出限DMP为0.988 ng,DEP为0.749 ng,DBP为0.702 ng,DEHP为1.920 ng.     

牛奶中酞酸酯污染物的气相色谱质谱-联用测定

建立了气相色谱.质谱法(GC-MS)测定市售牛奶中4种酞酸酯(邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二异丁基酯(DiBP)、邻苯二甲酸二丁基酯(DBP),邻苯二甲酸二(2-乙基己基)酯(DEHP))的方法.样品采用乙酸乙酯直接萃取,C18小柱净化,过0.45μm滤膜,直接注入GC-Ms进行分析.保留时间定性,外标法定量.4种酞酸酯的回收率为77.9%～109.07%;精密度(RSD)为1.72%～6.18%;检测限在0.15～60 ng之间.     

GC–MS法测定白酒中邻苯二甲酸二丁酯和邻苯二甲酸二(2-乙基)己酯

采用正己烷提取白酒中的邻苯二甲酸二丁酯(DBP)、邻苯二甲酸二(2-乙基)己酯(DEHP),建立了气相色谱–质谱法测定白酒中DBP,DEHP残留量的检测方法。对氮吹、水浴、盐析和直接提取4种方法的提取效率进行考察,选择氮吹法处理样品。在0.20~20 mg/L范围内DBP,DEHP的质量浓度分别与色谱峰面积呈良好的线性关系,线性相关系数分别为0.999 3,0.999 8。方法的定量限(S/N=10)为0.04 mg/kg,加标回收率在82.0%~92.5%之间,测定结果的相对标准偏差为1.91%~4.83%(n=6)。该方法适合白酒中DBP,DEHP残留量的日常检测。     

毛细管气相色谱法测定化妆品中的酞酸酯

建立了用毛细管气相色谱配氢火焰离子化检测器测定化妆品中6种酞酸酯(邻苯二甲酸二甲酯(DMP)、邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二丁酯(DBP)、邻苯二甲酸丁基苄基酯(BBP)、邻苯二甲酸二(2-乙基己)酯(DEHP)和邻苯二甲酸二正辛酯(DOP))的方法。样品用甲醇超声提取,经高速冷冻离心,清液经干燥脱水过0.5 μm滤膜过滤,直接注入气相色谱仪进行分析。然后,经过气相色谱-电子电离-质谱检测分析,确证气相色谱-氢火焰检测的阳性检出结果。用保留时间定性,外标法定量。6种酞酸酯的回收率为82.90%～     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.