介孔碳材料CMK-3的合成及其吸附性能研究——介绍一个综合化学实验

介绍一个集物理化学、分析化学和无机化学为一体的综合实验——介孔碳材料CMK-3的合成及其吸附性能研究。实验通过合成具有高比表面积的介孔碳材料CMK-3,运用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和氮气吸附/脱附技术表征材料的形貌和多孔结构;考察了介孔碳材料CMK-3对水溶液中次甲基蓝染料分子的吸附性能。     

电化学混合电容器用新型聚吡咯/介孔碳纳米复合电极

采用介孔碳CMK-3作为载体,通过化学原位聚合的方法制备出一种新型的聚吡咯/介孔碳(PPy-CMK-3)纳米复合材料.将该纳米复合材料作为正极,配以介孔碳CMK-3为负极和1.0mol·L-1NaNO3中性电解液,组装成为电化学混合电容器.电化学测试表明:在5.0mA·cm-2电流密度和1.4V充放电电位条件下,其放电比容量达57F·g-1,电容器功率密度为2.5×102W·kg-1,能量密度达17Wh·kg-1.当电流密度从5.0mA·cm-2增加至50mA·cm-2时,电容器的容量保持率在80%以上,显示高倍率充放电特性优异.此外,聚吡咯-介孔碳/介孔碳电化学混合电容器易活化,并具有优异的充放电效率和良好的循环稳定性能.     

超声辅助浸渍法制备高分散Pt/CMK-3-US加氢脱萘催化剂

以CMK-3介孔碳作为载体,分别采用传统浸渍法、超声辅助浸渍法、载体硝酸处理法和表面活性剂辅助浸渍法备了Pt/CMK-3、Pt/CMK-3-US、Pt/CMK-3-HNO_3和Pt/CMK-3-CTAB催化剂,并通过表征和催化性能评价进行研究。表征方法包括XRD、BET、SEM、TEM和H2-TPR,结果表明Pt/CMK-3中Pt分散性最差,Pt/CMK-3-HNO_3和Pt/CMK-3-CTAB中Pt的分散度较好,但是HNO_3对介孔碳的孔道结构有破坏作用,且Pt/CMK-3-HNO_3和Pt/CMK-3-CTAB中的介孔碳的表面性质具有明显变化,只有超声法可以在很好地保持CMK-3的孔道结构和表面性质的基础上提高铂的分散度,Pt的粒径在3 nm左右。萘加氢催化性能评价结果表明Pt/CMK-3-US的催化加氢活性及产物选择性高于Pt/CMK-3,且明显高于Pt/CMK-3-HNO_3和Pt/CMK-3-CTAB。萘转化率可以达到98%以上,十氢萘选择性可以达到95%以上。     

超声辅助浸渍法制备高分散Pt/CMK-3-US加氢脱萘催化剂

以CMK-3介孔碳作为载体,分别采用传统浸渍法、超声辅助浸渍法、载体硝酸处理法和表面活性剂辅助浸渍法备了Pt/CMK-3、Pt/CMK-3-US、Pt/CMK-3-HNO₃和Pt/CMK-3-CTAB催化剂,并通过表征和催化性能评价进行研究。表征方法包括XRD、BET、SEM、TEM和H₂-TPR,结果表明Pt/CMK-3中Pt分散性最差,Pt/CMK-3-HNO₃和Pt/CMK-3-CTAB中Pt的分散度较好,但是HNO₃对介孔碳的孔道结构有破坏作用,且Pt/CMK-3-HNO₃和Pt/CMK-3-CTAB中的介孔碳的表面性质具有明显变化,只有超声法可以在很好地保持CMK-3的孔道结构和表面性质的基础上提高铂的分散度,Pt的粒径在3 nm左右。萘加氢催化性能评价结果表明Pt/CMK-3-US的催化加氢活性及产物选择性高于Pt/CMK-3,且明显高于Pt/CMK-3-HNO₃和Pt/CMK-3-CTAB。萘转化率可以达到98%以上,十氢萘选择性可以达到95%以上。     

有序介孔碳CMK-3的化学活化及储氢性能

选用KOH、NaOH、H3PO4对有序介孔碳CMK-3进行了活化,通过X射线衍射、低温氮吸附-脱附等对样品进行了表征,发现活化后样品的结构发生了巨大的变化。有序介孔碳CMK-3的有序性逐渐降低,比表面积明显增大,2 nm介孔明显增多。讨论了CMK-3和KOH质量比、活化温度、不同活化剂对活化效果的影响。储氢测试表明活化能够明显提高CMK-3的储氢性能,77K、100 kPa时的储氢性能高达2.32wt%。     

有序介孔碳负载Fe、Co、Ni纳米晶的软模板合成及其表征

报道了在有序介孔碳基体中一步合成负载Fe、Co、Ni纳米晶的方法. 以间二苯酚和甲醛为碳源, F127为模板剂, Fe、Co、Ni的硝酸盐为前驱体, 通过软模板组装路线在酸性条件下合成了负载型有序介孔碳复合材料. 采用X射线衍射(XRD)、透射电镜(TEM)和氮气吸附等手段对所合成材料进行了表征. 结果表明: 合成的材料具有类似于SBA-15的有序介孔结构, 有序介孔碳负载Fe、Co、Ni纳米晶复合材料的比表面积分别为586、626和698 m²·g^-1. XRD和TEM表征结果证实了金属物种以高分散纳米晶的形式分布在介孔碳基体中.     

Zn-空气电池中二维与三维结构碳负载Mn3O4的催化性能比较

采用湿法浸渍将Mn3O4负载到不同碳材料的表面, 测试了这些复合材料用于空气电极催化剂的电催化性能. 通过充放电和循环伏安等电化学测试发现, 具有三维孔道结构的介孔碳材料(CMK-3)的催化性能远比二维孔道结构的介孔碳(OMC)的好. 从透射电子显微镜观察发现, 氧化锰粒子均负载在碳的外表面, 位于三维孔道外表面的氧化锰可以与电解液和碳孔道内的氧气同时接触. 这种结构产生了大量有效的三相反应界面, 从而达到良好的催化效果.     

载铜介孔碳CMK-3的制备及其对苯酚的吸附-催化氧化性能

通过一种简易的方法在介孔碳CMK-3的孔道内负载氧化铜粒子制备Cu/CMK-3复合物,利用粉末X射线衍射、氮气吸附-脱附、透射电镜等手段对其进行表征.结果表明,氧化铜均匀地分散在CMK-3孔道中,CMK-3在负载氧化铜后仍有较大的比表面积.考察了载铜CMK-3对水中苯酚的吸附和低温干法催化氧化苯酚性能.吸附和循环使用结果表明,Cu/CMK-3对水中苯酚具有较大的吸附量和良好的催化氧化效率.热重-质谱(TG-MS)联用测试结果表明,吸附的苯酚在180℃左右开始被催化氧化为CO2和水,此时不会造成苯酚的脱附和介孔碳CMK-3的烧蚀.     

有序介孔碳/石墨烯/镍泡沫的制备及其对多巴胺的高灵敏度和高选择性检测

柔性生物传感器在可穿戴电子设备中有着广泛的应用前景. 为了获得柔性电化学多巴胺传感器,作者在本工作中首先在镍泡沫表面通过化学气相沉积生长石墨烯,随后通过高温碳化嵌段共聚物与酚醛树脂在石墨烯表面共组装形成的薄膜制备了有序介孔碳/石墨烯/镍泡沫（OMC/G/Ni）复合材料. 其中,镍泡沫可以为复合材料提供具有高导电性和良好柔韧性的金属骨架,而具有垂直排列介孔阵列的有序介孔碳层为复合材料提供了高的电活性表面积,且有利于活性位点的暴露. 值得注意的是,夹在有序介孔碳层和镍泡沫之间的石墨烯极大地增强了各组分之间的相容性,有利于进一步提升复合材料的电化学性能. 作为电化学传感器中的工作电极,OMC/G/Ni体现出优异的多巴胺检测能力. 不但具有宽的线性检测范围（0.05 ~ 58.75 μmol·L^-1）和低检测限（0.019 μmol·L^-1）,还具有良好的选择性、重现性和稳定性. 此外,OMC/G/Ni在弯曲状态下依旧能够保持对多巴胺的高检测能力,证明了其在柔性生物传感器中的应用潜力.     

不同孔径的介孔碳分子筛对VB12的吸附性质研究

摘要利用SBA-15为模板, 在不同温度下合成了孔径大小在3.7(CMK-3-100)和6-3 nm(CMK-3-150)之间的介孔碳， 以其作为吸附剂, 研究了它们在水溶液中对VB12的吸附作用. 结果表明, CMK-3-130与CMK-3-100和CMK-3-150相比， 表现出对VB12最大的吸附能力(吸附能力为412.5 mg/g), 这是因为它有比较高的有序结构和比较大的孔容.     

Highly Branched Metal Alloy Networks with Superior Activities for the Methanol Oxidation Reaction

Three‐dimensional (3D) interconnected metal alloy nanostructures possess superior catalytic performance owing to their advantageous characteristics, including improved catalytic activity, corrosion resistance, and stability. Hierarchically structured Ni‐Cu alloys composed of 3D network‐like microscopic branches with nanoscopic dendritic feelers on each branch were crafted by a facile and efficient hydrogen evolution‐assisted electrodeposition approach. They were subsequently exploited for methanol electrooxidation in alkaline media. Among three hierarchically structured Ni‐Cu alloys with different Ni/Cu ratios (Ni_0.25Cu_0.75, Ni_0.50Cu_0.50, and Ni_0.75Cu_0.25), the Ni_0.75Cu_0.25 electrode exhibited the fastest electrochemical response and highest electrocatalytic activity toward methanol oxidation. The markedly enhanced performance of Ni_0.75Cu_0.25 eletrocatalyst can be attributed to its alloyed structure with the proper Ni/Cu ratio and a large number of active sites on the surface of hierarchical structures.     

钇替代镧对La-Mg-Ni系储氢合金晶体结构及其电化学性能的影响

通过少量Y对La的取代,研究了La0.75-xYxMg0.25Ni3.17Al0.13和La0.75-xYxMg0.25Ni3.37Al0.13(其中x=0.00,0.05,0.10)体系中Y对合金晶体结构及电化学性能的影响。通过X射线衍射实验、电化学性能测试,结果表明上述两体系主相为Ce2Ni7相、Pr5Co19相。少量的取代对活化性能、最大放电容量影响不大,但对循环稳定性、放氢平台压影响显著,而且在不同主相结构中,影响效果不一样。当x从0.00增大到0.10时:主相为Ce2Ni7相La0.75-xYxMg0.25Ni3.17Al0.13的S80%由222周下降到112周,放氢平台压则由0.015 MPa上升到0.045 MPa;而主相为Pr5Co19相La0.75-xYxMg0.25Ni3.37Al0.13的S80%由172周下降到127周,放氢平台压则由0.019 MPa上升到0.076 MPa。     

In Situ Growth of Hierarchical Ni-Mn-O Solid Solution on a Flexible and Porous Ni Electrode for High-Performance All-Solid-State Asymmetric Supercapacitors

To endow all-solid-state asymmetric supercapacitors with high energy density, cycling stability, and flexibility, we design a binder-free supercapacitor electrode by in situ growth of well-distributed broccoli-like Ni_0.75Mn_0.25O/C solid solution arrays on a flexible and three-dimensional Ni current collector (3D-Ni). The electrode consists of a bottom layer of compressed but still porous Ni foam with excellent flexibility and high electrical conductivity, an intermediate layer of interconnected Ni nanoparticles providing a large specific surface area for loading of active substances, and a top layer of vertically aligned mesoporous nanosheets of a Ni_0.75Mn_0.25O/C solid solution. The resultant 3D-Ni/Ni_0.75Mn_0.25O/C cathode exhibits a specific capacitance of 1657.6 mF cm⁻² at 1 mA cm⁻² and shows no degradation of the capacitance after 10 000 cycles at 3 mA cm⁻². The assembled 3D-Ni/Ni_0.75Mn_0.25O/C//activated carbon asymmetric supercapacitor has a high specific capacitance of 797.7 mF cm⁻² at 2 mA cm⁻² and an excellent cycling stability with 85.3 % of capacitance retention after 10 000 cycles at a current density of 3 mA cm⁻². The energy density and power density of the asymmetric supercapacitor are up to 6.6 mW h cm⁻³ and 40.8 mW cm⁻³, respectively, indicating a fairly promising future of the flexible 3D-Ni/Ni_0.75Mn_0.25O/C electrode for efficient energy storage applications.     

CS/La0.7Ca0.3Fe0.25Co0.75O3复合纳米颗粒的制备及光催化性能研究

采用甘氨酸-硝酸盐燃烧法成功的制备了La0.7 Ca0.3 Fe0.25 Co0.75 O3钙钛矿型复合氧化物,将钙钛矿La0.7Ca0.3Fe0.25Co0.75O3与壳聚糖(CS)共混交联制备出一种新型的光催化剂,通过XRD、SEM、FT-IR对催化剂的结构进行了表征.以酸性橙为对象,高压汞灯紫外光为光源,研究了一...     

Patterning of magnetic bimetallic coordination nanoparticles of Prussian blue derivatives by the Langmuir-Blodgett technique

We report a novel method to prepare patterns of nanoparticles over large areas of the substrate. This method is based on the adsorption of the negatively charged nanoparticles dispersed in an aqueous subphase onto a monolayer of the phospholipid dipalmitoyl-l-α-phosphatidylcholine (DPPC) at the air-water interface. It has been used to prepare patterns of nanoparticles of Prussian blue analogues (PBA) of different size (K(0.25)Ni[Fe(CN)(6)](0.75) (NiFe), K(0.25)Ni[Cr(CN)(6)](0.75) (NiCr), K(0.25)Ni[Co(CN)(6)](0.75) (NiCo), Cs(0.4)Co[Cr(CN)(6)](0.8) (CsCoCr), and Cs(0.4)Co[Fe(CN)(6)](0.9) (CsCoFe)). The behavior of DPPC monolayer at the air-water interface in the presence of the subphase of PBA nanoparticles has been studied by the compression isotherms and Brewster angle microscopy (BAM) images. Atomic force microscopy (AFM) of the transferred films on mica substrates shows that patterns of the nanoparticles are observed for a 10(-4) M concentration of the subphase, based on the nanoparticle precursors, at surface pressures between 1 and 6 mN/m and transfer velocities from 10 to 80 mm/min. Vertical, horizontal, or tilted fringes of the nanoparticles with respect to the transfer direction can be obtained depending on the transfer velocity and surface pressure.     

Synthesis, characterization and activity of Co and Ni catalysts supported on AlMe (Me?=?Zn, Zr, Ti) mixed oxides

Binary Al?CTi, Al?CZr and Al?CZn oxides, prepared by the sol?Cgel method were used as supports of catalytic systems. The catalysts were prepared by impregnation of these supports with the low cost Co or Ni nitrate salts and subsequent calcination at 700?°C. Catalysts have been characterized by S_BET, XRD and TPR techniques. The catalysts were tested in ethanol partial oxidation using a fixed-bed quartz reactor at atmospheric pressure and temperature at 600?°C. In test reactions a constant feed composition was used with O₂/EtOH molar ratio of 0.75 in nitrogen balance. The catalytic performance of the systems depends on type of support and type of promoter. Hydrogen and CO are the predominant products beside some by-products in different quantities (CO₂, methane, ethylene, acetaldehyde, acetone, acetic acid). The Co and Ni catalysts supported on AlZn binary oxide showed the highest selectivity to hydrogen and to carbon monoxide with full ethanol conversion. Selectivity of hydrogen follows the order of Co(Ni)AlZn?>?Co(Ni)AlTi?>?Co(Ni)AlZr. The best performance was obtained by NiAlZn catalyst with 89?% hydrogen selectivity.     

高容量正极材料0.08LiCo0.75Al0.25O2-0.92LiNiO2的合成与电化学性能研究

在恒定pH值下将层状钴铝双羟基复合金属氧化物(CoAl-LDH)均匀包覆在球状Ni(OH)2表面,与LiOH.H2O混合均匀后,经高温煅烧制得钴铝酸锂包覆镍酸锂0.08LiCo0.75Al0.25O2-0.92LiNiO2正极材料.电化学测试表明,0.08LiCo0.75Al0.25O2-0.92LiNiO2正极比容量高,具有良好的倍率性能和循环寿命,其0.1C放电比容量为211 mAh·g-1,0.5C放电比容量为195.6 mAh·g-1,3C放电比容量为161 mAh·g-1,0.5C 30周期循环后容量保持率为93.2%,明显优于LiNiO2和钴酸锂包覆镍酸锂0.08LiCoO2-0.92LiNiO2正极.     

Characterization of magnetic nanoparticles using energy-selected transmission electron microscopy.

Fe, Co, and Ni magnetic nanoparticles have been characterized using energy-selected imaging in a high-resolution transmission electron microscope. The samples comprised Fe/FeO x and Co/CoO x nanoparticles synthesized by inert gas evaporation and a Ni/C nano-composite prepared by a sonochemical method. All of the particles examined were found to be between 5 and 30 nm in size, with the Fe and Co crystals coated in 5-10 nm of metal oxide layer and the Ni metallic crystallites embedded in an amorphous carbon spherical matrix.     

Theoretical investigation of half‐metallicity in Co/Ni substituted AlN

Results of Co and Ni substituted AlN in the zinc blende phase are presented. For spin up states, the hybridized N‐2p and Co/Ni‐3d states form the valance bands with a bandgap around the Fermi level for both materials, while in the case of the spin down states, the hybridized states cross the Fermi level and hence show metallic nature. It is found that, Al_0.75Co_0.25N and Al_0.75Ni_0.25N are ferromagnetic materials with magnetic moments of 4 μ_B and 3 μ_B, respectively. The integer magnetic moments and the full spin polarization at the Fermi level make these compounds half‐metallic semiconductors. Furthermore it is also found that the interaction with the N‐2p state splits the 5‐fold degenerate Co/Ni‐3d states into t_2g and e_g states. The t_2g states are located at higher energies than the e_g states caused by the tetrahedral symmetry of these compounds. © 2011 Wiley Periodicals, Inc. Int J Quantum Chem, 2011     

Factors controlling the energetics of the oxygen reduction reaction on the Pd-Co electro-catalysts: insight from first principles

We report here results of our density functional theory based computational studies of the electronic structure of the Pd-Co alloy electrocatalysts and energetics of the oxygen reduction reaction (ORR) on their surfaces. The calculations have been performed for the (111) surfaces of pure Pd, Pd(0.75)Co(0.25) and Pd(0.5)Co(0.5) alloys, as well as of the surface segregated Pd/Pd(0.75)Co(0.25) alloy. We find the hybridization of dPd and dCo electronic states to be the main factor controlling the electrocatalytic properties of Pd/Pd(0.75)Co(0.25). Namely the dPd-dCo hybridization causes low energy shift of the surface Pd d-band with respect to that for Pd(111). This shift weakens chemical bonds between the ORR intermediates and the Pd/Pd(0.75)Co(0.25) surface, which is favorable for the reaction. Non-segregated Pd(0.75)Co(0.25) and Pd(0.5)Co(0.5) surfaces are found to be too reactive for ORR due to bonding of the intermediates to the surface Co atoms. Analysis of the ORR free energy diagrams, built for the Pd and Pd/Pd(0.75)Co(0.25), shows that the co-adsorption of the ORR intermediates and water changes the ORR energetics significantly and makes ORR more favorable. We find the onset ORR potential estimated for the configurations with the O-OH and OH-OH co-adsorption to be in very good agreement with experiment. The relevance of this finding to the real reaction environment is discussed.