首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
本文建立了准确、快速、经济的控制缓释肥料中尿素态氮的测定方法。采用自制黄豆脲酶水解液,于pH7.0的磷酸盐缓冲体系中水解尿素,以奈氏试剂为显色剂,用分光光度法测定尿素态氮。该方法在0~2.50μg/mL范围内符合比耳定律,检出限为0.01μg/mL,用于控制缓释肥料中尿素态氮的测定,回收率在96.2%到100.8%之间,与商品脲酶测定结果接近。  相似文献   

2.
氢化物发生-原子荧光光谱法测定中草药中不同形态的砷   总被引:9,自引:0,他引:9  
本文建立了氢化物发生-原子荧光光谱法测定中草药方剂原生药、残渣、悬浮态及可溶态中的三价及五价砷的方法。研究了仪器的工作条件、试剂浓度及不同增感剂对砷原子荧光强度的影响和五价砷的还原条件,探讨了共存离子对砷测定的干扰及消除方法。利用本方法成功地对黄连解毒汤中的砷进行了形态分析。方法检出限为89.1ng/L,RSD为1.24%,样品加标回收率为91.1%~109.3%。  相似文献   

3.
CuO-BaO/SiO2催化剂的结构表征   总被引:9,自引:0,他引:9  
以XRD、XPS和EXAFS手段对CuO-BaO/Sic2催化剂及其还原态的结构进行了研究.结果表明,在CuO-BaO/SiO2体系中铜和钡都是以氧化态的形式存在,超细SiO2载体对所负载的CuO的结构有影响.随着样品负载量的逐渐降低,Cu-O和Cu-Cu睡的健长和配位数逐渐征小,而且低载量样品的健长和配位数减小的幅度最大.在总负载量>13.39%的样品中,CuO以晶相的形式存在;总负载量<13.39%的样品中,CUO呈现单层分布的高分出状态.还原态样品中钢以本价铜的形式存在,随负载量的降低,还原态Cu-Cu健的镇长和配位数也分别呈现出逐渐减小的趋势.还原态中心铜原子在催化剂表面的分布状态基本上保持了氧化态催化剂中CuO物相的分市状态.  相似文献   

4.
钼镍负载催化剂表面组份及其活性的研究   总被引:10,自引:0,他引:10  
利用X光光电子能谱(XPS),激光拉曼光谱(LRS)和程序升温还原(TRP)等技术,研究了高载钼量的负载钼镍催化剂的表面组份形式.结果表明,催化剂在氧化态、还原态、硫化态时表面的主要组份分别以类似NiMoO_4结构的NiMo_xO_y多种价态钼酸盐及金属镍,氧硫钼镍及硫化钼形式存在.三种化学态的加氢脱硫活性顺序为硫化态,还原态>>氧化态.还原态表面检测到金属镍,据此提出了金属镍所产生的氢溢流效应是还原态活性明显增加的一个原因.文中由硫化态、还原态表面组份与反应活性之间的关联结果支持了Kwart提出的多点催化反应机理.  相似文献   

5.
Cu/WO3-NiO上光促表面催化二氧化碳与水合成甲醇反应的规律   总被引:12,自引:0,他引:12  
 采用溶胶-凝胶法制备了n-p复合半导体材料0.75%Cu/WO3-1.5%NiO,用X射线衍射、透射电镜、红外光谱、紫外-可见光漫反射和程序升温脱附等技术对材料结构、吸光性能和化学吸附性能进行了表征,研究了该材料对CO2与H2O合成CH3OH的光促表面催化反应(PSSR)规律.结果表明:所制备的材料明显有利于促进目的反应,室温条件下就有CH3OH生成,选择性超过90%,升高反应温度可提高CH3OH产量,且选择性仍高于88%.根据实验结果,得出CO2在材料表面的卧式吸附态为CH3OH的前驱物,并对PSSR机理进行了讨论.  相似文献   

6.
用环形扩散管和滤纸联用采样技术采集空气中氨和铵盐   总被引:1,自引:0,他引:1  
黎源倩  汪莉 《分析化学》1997,25(2):238-242
建立了环形扩散管和滤纸采样夹联用,分形态同时采集空气中所态氨和颗粒态铵盐的方法。在同一气流中,采用涂渍1.5%草酸乙醇水溶液的环形扩散管采集气态氨,用浸渍上述试剂的玻璃纤维纸和慢速定量滤纸分别采集颗粒安和第一层滤纸上的铵盐挥发产生的氨气。用靛酚蓝比色法分别测定氨和铵盐。当采气流速为1.0L/min时,采样效率高于98.2%。将本法测得的氨气和铵盐的总量与标准采样方法的测定结果比较。无显著性差异(P  相似文献   

7.
研究了钨丝电沉积石墨炉原子吸收光谱法测定不稳定态铅的条件。结果表明该方法的灵敏度比常规CFAAS法提高80倍,检出限为0.01μg.L-1;变异系数4.5%,在0-2.5μg·L-1范围内线性关系好,抗干扰强。测定了食品中不稳定态铅。  相似文献   

8.
2,6-二甲酚分光光度法测定废水中的总氮   总被引:1,自引:0,他引:1  
废水中的无机态氮和有机态氮被过硫酸钾氧化消解后转变为硝酸盐,在硫酸和磷酸混合酸介质中,硝酸盐与2,6—二甲酚反应生成4—硝基—2,6—二甲酚而显色。废水中的总氮在2~8mg/L范围内与337nm波长处的吸光度成正比,回归方程为A=0.1672X—0.0077,相关系数r=0.9996,回收率为96.5%~105.7%。氯离子浓度高于1.5g/L时有干扰,其它常见的阴、阳离子无干扰。  相似文献   

9.
β-二酮钴配合物催化空气氧化二苯甲醇反应的研究   总被引:3,自引:0,他引:3  
研究了β-二酮钴催化空气氧化二苯甲醇生成二苯甲酮的反应.利用正交实验方法考察了反应温度、时间、N-羟基邻苯二甲酰亚胺(NHPI)用量、催化剂种类及用量对反应的影响.发现同一金属中低价态β-二酮金属配合物的活性较高,配体给电子能力强,催化活性就越高.当反应温度80℃、反应时间12h、NHPI为l0%、Co(acac)2为0.9%时,二苯甲醇的转化率高达97.6%.  相似文献   

10.
用反相悬浮聚合法制备了交联度分别为10%、7.5%、5%、1%、0.5%及0.25%的丙烯酰胺-丙烯酸P(AAM-NaAA)交联共聚水凝胶,用HNMR驰豫方法测定了水及聚合物主链上(-CH2CH-)基团中质子的自旋-自旋驰豫时间(T2),并结合质子线型分析,研究了交联凝胶在溶胀态下的内部分子运动,讨论了不同交联度下谱线线宽及驰豫变化的机制。结果表明,由于交联使凝胶内部各向异性相互作用增强,存在有残余的偶极-偶极相互作用,质子语具有特征的超Lorentz线型;质子线宽比非交联态时加大,水及主链的T2随交联度的加大而减小,反映了内部分子运动由强变弱的过程;水的T2驰豫不是单纯的单指数驰豫行为,表明凝胶内部有较强的键合束缚水存在,与DSC实验的结论一致。  相似文献   

11.
用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.  相似文献   

12.
A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.  相似文献   

13.
The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp3)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp2)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp2)?H and aliphatic 1,5- and 1,6-C(sp3)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp3)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp2)?H insertion.  相似文献   

14.
In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.  相似文献   

15.
N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).  相似文献   

16.
An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y1 and Y2. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.  相似文献   

17.
The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.  相似文献   

18.
In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.  相似文献   

19.
KMnO4-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.  相似文献   

20.
The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号