柱面天线射频感性耦合等离子体放电模式特性的实验研究

利用Z-scan、电流、电压探头,通过测量等离子体吸收功率、天线电流、电压、等离子体直流悬浮电位等多种参数,研究了匹配网络、天线耦合强度、导电地面积、气压等多种因素对E,H放电模式特性及模式转化行为的影响.基于Γ型阻抗匹配网络中串联电容对射频电源输出功率的影响,提出了E—H放电模式转化的正负反馈区概念.研究发现：在相同的其他放电条件下,处于正反馈区时等离子体放电易于产生跳变型模式转化,而且模式跳变的临界天线电流、回滞宽度、跳变临界功率、跳变功率差等参数均随阻抗匹配网络参数产生明显变化;在负反馈区内,模式转化过程趋于连续.由于阻抗匹配网络的影响,E—H模式的跳变电流并不是总大于H—E模式的跳变电流.在不同导电地面积、阻抗匹配网络、气压下,模式转化过程中等离子体直流悬浮电位的变化呈现多样性. 关键词： 射频等离子体 感性耦合 容性耦合 模式转化     

均匀磁化等离子体与雷达波相互作用的数值分析

采用平板几何对不同磁场强度下等离子体对电磁波的吸收、反射和透射特性进行了数值分析.结果表明,不同磁场可以显著改变等离子体对不同频率的雷达波的吸收和反射特性.当雷达波频率接近等离子体高混杂频率时,磁化等离子体将对该波产生强的共振吸收,带宽在2GHz左右,吸收比可达90%以上.因此,通过适当调整磁场强度、等离子体密度和碰撞频率,可实现较宽雷达波段的等离子体隐身 关键词： 电磁波 磁化等离子体 共振吸收 等离子体隐身     

大气压微波等离子体炬的仿真设计与实验

设计了一个低成本、高稳定性的基于BJ22矩形波导的微波等离子体炬源。整个系统由1～10 kW主频2.45 GHz的磁控管微波功率源、环形器、调谐器和微波反应腔体组成。通过特殊设计的调谐装置,在气体喷嘴处产生高幅值的电场强度,使工作气体电离形成大气压开放式微波等离子体炬。对影响电场强度的几个关键因素进行了仿真,得出各个参数对场强的影响规律;根据仿真参数设计了微波反应腔体,该系统可以在大气压下激发和维持开放的稳定氩气、氦气、氮气和空气等离子体炬。对等离子体炬的基本特性和基本参数进行了研究,验证了设计参数的正确性,讨论了其可扩展性及潜在的工业应用。     

有源等离子体在开放大气环境下的反应扩散过程研究

利用一维模型用数值模拟的方法,研究了低气压开放环境下大气等离子体在存在等离子体源的情况下的反应扩散过程.得到了考虑化学反应、扩散以及漂移共同作用下的大气等离子体的主要成分随等离子体注入流量的变化规律及一定流量情况下主要带电成分随时空的演化规律. 将数值模拟结果与一个近似解析公式相衔接,估计达到稳态时维持一定电子密度所需要的等离子体流量,可据此进一步估计所需功率. 关键词： 大气等离子体 等离子体源 数值模拟 反应扩散过程     

Numerical investigation of the plasma processes for propellant heating in electrothermal plasma thruster for nanosatellites

Numerical investigation of the plasma processes in a cylindrical chamber with small dimensions of a novel microwave electrothermal plasma thruster for nanosatellites has been conducted. The absorbed microwave power from the electrons in the plasma column of the surface wave discharge is included in the computational model as a heat source with Gaussian distribution. The computational model takes into account the elastic and inelastic collisions of the electrons with the atoms in the ground state and two excited states (−s, −p) and the processes of recombination and deactivation of the plasma species in the volume and on the walls of the chamber. The computational model includes the flow of neutral gas and the processes in the plasma for effective heating of neutral particles by collisions not only with electrons but also with ions. Selected combinations of input power and propellant mass flow rates are used as initial parameters for the numerical investigation. The results show that at higher mass flow rates the heating of the neutral gas is more effective and at power levels of 4 W and propellant mass flow rate of 3 mg/s the electrothermal plasma thruster demonstrates effective performance and thrust levels in the order of 1 mN.     

大面积表面波等离子体源微波功率吸收的数值模拟研究

建立了大面积矩形表面波等离子体(SWP)源全尺寸的三维模型,用数值模拟的方法研究了SWP源基于碰撞的功率吸收问题,给出了随等离子体参数变化的微波反射率曲线,分析了不同天线对微波功率沉积的影响,并讨论了微波功率吸收和表面波的定性关系. 结果发现,均匀放电的SWP源功率沉积本质是由表面波等离子体的性质决定的,等离子体密度太大或太小都不利于功率吸收. 在正常工作气压下,SWP源通过碰撞机理即可以实现微波功率的有效沉积,微波吸收率可达80%以上,与已有实验相符. 本研究同时发现,天线阵列激发的表面波模式越紧凑,强度越大,越有利于微波的吸收. 关键词： 时域有限差分法 等离子体表面波 功率吸收 狭缝天线     

SECRAL等离子体中EUV光功率的产生

The high power EUV source is one of key issues in the development of EUV lithography which is considered to be the most promising technology among the next generation lithography.However neither DPP nor LPP seems to meet the requirements of the commercial high-volume product.Insufficiency of DPP and LPP motivate the investigation of other means to produce the EUV radiation required in lithography.ECR plasma seems to be one of the alternatives.In order to investigate the feasibility of ECR plasma as a EUV light source,the EUV power emitted by SECRAL was measured.A EUV power of 1.03W in 4~ sr solid angle was obtained when 2000W 18GHz rf power was launched,and the corresponding CE was 0.5%.Considering that SECRAL is designed to produce very high charge state ions,this very preliminary result is inspiring. Room-temperature ECR plasma and Sn plasma are both in the planned schedule.     

Experimental results of helicon sources

Helicon plasma sources are known as efficient generators of uniform and high density plasma.A helicon plasma source was developed for the investigation of plasma stripping and plasma lenses at the Institute of Modern Physics, CAS.In this paper, the characteristics of helicon plasma have been studied by using a Langmuir four-probe and a high plasma density up to 3.9×10~(13)/cm~3 has been achieved with the Nagoya type Ⅲ antenna.In the experiment, several important phenomena were found: (1) for a given magnetic induction intensity, the plasma density became greater with the increase of RF power; (2) helicon mode appeared at RF power between 300 W and 400 W; (3) the plasma density gradually tended to saturation as the RF power increased to the higher power; (4) a higher plasma density can be obtained by a good match between the RF power and the magnetic field distribution.The key issue is how to optimize the matching between the RF power and the magnetic field.Moreover, some tests on the extraction of ion beams were performed, and preliminary results are given.The problems which existed in the helicon ion source will be discussed and the increase in beam density will be expected by extraction system optimum.     

大气微波等离子体炬装置设计及实验研究

大气微波等离子体矩具有无电极放电污染、无需昂贵真空设备和易于连续化加工等特点,具有广阔的应前景.本文设计了一套基于BJ26波导的微波能利用率高、稳定性好的大气微波等离子体装置.该装置由最高输出功为800W的2.45GHz程控微波源、调配系统、波导谐振腔和耦合天线组成.利用加装游标卡尺的接触式短路活塞,微波反射面位置进行...     

Self-consistent three-dimensional modeling and simulation of large-scale rectangular surface-wave plasma source

A self-consistent and three-dimensional (3D) model of argon discharge in a large-scale rectangular surface-wave plasma (SWP) source is presented in this paper, which is based on the finite-difference time-domain (FDTD) approximation to Maxwell's equations self-consistently coupled with a fluid model for plasma evolution. The discharge characteristics at an input microwave power of 1200~W and a filling gas pressure of 50~Pa in the SWP source are analyzed. The simulation shows the time evolution of deposited power density at different stages, and the 3D distributions of electron density and temperature in the chamber at steady state. In addition, the results show that there is a peak of plasma density approximately at a vertical distance of 3~cm from the quartz window.     

感应耦合等离子体中和枪的电子引出特性研究

给出了一种感应耦合等离子体源的设计,用于等离子体中和枪装置。通过实验方法研究等离子体源的电子引出特性,并结合理论分析了等离子体密度随射频功率的变化关系。研究结果表明等离子体源的电子引出特性与放电腔内气压有关联性,E?H模式转换中电子密度的变化与负载的电感值相关。研究成果对等离子体中和枪的发展有重要的参考价值。     

Review of relaxation oscillations in plasma processing discharges

Relaxation oscillations due to plasma instabilities at frequencies ranging from a few Hz to tens of kHz have been observed in various types of plasma processing discharges. Relaxation oscillations have been observed in electropositive capacitive discharges between a powered anode and a metallic chamber whose periphery is grounded through a slot with dielectric spacers. The oscillations of time-varying optical emission from the main discharge chamber show, for example, a high-frequency (\sim 40~kHz) relaxation oscillation at 13.33Pa, with an absorbed power being nearly the peripheral breakdown power, and a low-frequency ( \sim 3 Hz) oscillation, with an even higher absorbed power. The high-frequency oscillation is found to ignite plasma in the slot, but usually not in the peripheral chamber. The kilohertz oscillations are modelled using an electromagnetic model of the slot impedance, coupled to a circuit analysis of the system including the matching network. The model results are in general agreement with the experimental observations, and indicate a variety of behaviours dependent on the matching conditions. In low-pressure inductive discharges, oscillations appear in the transition between low-density capacitively driven and high-density inductively driven discharges when attaching gases such as SF₆ and Ar/SF₆ mixtures are used. Oscillations of charged particles, plasma potential, and light, at frequencies ranging from a few Hz to tens of kHz, are seen for gas pressures between 0.133 Pa and 13.33 Pa and discharge powers in a range of 75--1200 W. The region of instability increases as the plasma becomes more electronegative, and the frequency of plasma oscillation increases as the power, pressure, and gas flow rate increase. A volume-averaged (global) model of the kilohertz instability has been developed; the results obtained from the model agree well with the experimental observations.     

激光与固体靶面烧蚀等离子体的能量耦合计算

 强激光辐照下固体靶表面迅速汽化产生靶蒸气等离子体,激光穿过等离子体区到达固体靶表面的过程就是激光束与等离子体的能量耦合与交换过程。采用具有五阶精度的WENO差分格式和简易等离子体状态方程模型对激光与等离子体相互作用的复杂物理过程进行了数值计算,分析了激光束能量在等离子体区中的吸收、屏蔽效应等动态耦合规律以及激光支持等离子体前驱冲击波传播。数值模拟结果表明：激光能量是支持靶面等离子体运动的唯一原因,能量屏蔽效应对激光与等离子体能量耦合有很大影响,通过控制激光脉冲宽度,可以合理调节屏蔽效应的影响。     

Bi靶激光等离子体极紫外光源以及碎屑辐射特性研究

激光等离子体极紫外光源具有体积小、稳定性高和输出波长可调节等优势,在极紫外光刻领域发挥着重要的作用。Bi靶激光等离子体极紫外光源在波长9～17 nm范围内具有较宽的光谱,可应用于制造极紫外光刻机过程中所需的极紫外计量学领域。利用平像场光谱仪和法拉第杯对Bi靶激光等离子体极紫外光源以及离子碎屑辐射特性进行了实验研究。在单脉冲激光打靶条件下,实验中观察到Bi靶激光等离子极紫外光谱在波长12.3 nm处出现了一个明显的凹陷,其对应着Si L-edge的吸收,是Bi元素光谱的固有属性。相应地在波长为11.8和12.5 nm位置处产生了两个宽带的辐射峰。研究了两波长光谱特性以及辐射强度随激光功率密度的变化。结果表明,在改变聚焦光斑大小实现不同激光功率密度（0.7×1010～3.1×1010 W·cm-2）过程中,当功率密度为2.0×1010 W·cm-2时两波长处的光辐射最强,其原因归结为Bi靶极紫外光辐射强度受激光能量用于支撑等离子膨胀的损失和极紫外光被等离子体再吸收之间的平衡制约所致。在改变激光能量实现不同激光功率密度过程中,由于烧蚀材料和产生两波长所需高阶离子随着功率密度的增加而增加,增强了两波长处的光辐射。进一步,研究了双脉冲激光对Bi靶极紫外光谱辐射特性影响,实验发现双脉冲打靶下原来在单脉冲打靶时出现在波长13～14 nm范围内的凹陷消失。最后,对单脉冲激光作用Bi靶产生极紫外光源碎屑角分布进行了测量。结果表明,当探测方向从靶面法线方向移动到沿着靶面方向上的过程中,探测到Bi离子动能依次减小,并且离子动能随激光脉冲能量降低而呈线性减小。此项研究有望为我国在研制极紫外光刻机过程所需的计量学领域提供技术支持和打下夯实的基础。     

60MHz电容耦合等离子体中电子能量分布函数特性研究

甚高频(频率大于30 MHz)耦合放电源由于能产生大面积高密度的等离子体而受到了人们的广泛关注. 采用电流、电压探针以及朗缪尔探针诊断技术对60MHz射频激发产生的容性耦合等离子体的放电特性及电子行为进行了研究. 实验结果表明,等离子体的等效电阻/电容随着射频输入功率的增加而减小/增加;等离子体中电子行为不仅依赖于射频输入功率,还与放电气压密切相关;放电气压的增加导致电子能量概率分布函数(EEPF)从双温Maxwellian分布向Druyvesteyn分布转变,而且转变气压远低于文献所报道的数值,这主要是由于在60MHz容性耦合等离子体中电子反弹共振加热效率大为降低. 关键词： 甚高频容性耦合等离子体 朗缪尔探针诊断 电子加热模式     

射频等离子体光源高效固态功率源的设计

针对射频等离子体光源(LEP)开发了一种较高抗负载失配能力的高效驱动功率源.采用三次谐波开路和偶次谐波短路,并利用集总参数和分布参数相结合的拓扑结构,实现了谐波控制的高效F类功率放大器;利用单片机控制固态源的工作频率,使其与光源谐振频率的变化一致,减小功放输出的驻波比,提高长期可靠性.对高效固态功率源进行连续波满功率测...     

Interaction of electromagnetic waves with a magnetized nonuniform plasma slab

The absorption, reflection, and transmission of electromagnetic waves by a nonuniform plasma slab immersed in an ambient uniform magnetic field of various strengths are studied in this paper. The effects of the plasma parameters and magnetic field strength on the absorbed, reflected, and transmitted power are discussed. The magnetized nonuniform plasma slab is modeled by a series of magnetized uniform plasma subslabs. The calculation results show that the effects of the magnetic field strength and density gradient on the absorbed power, as well as the frequency band of resonant absorption, are significant. A complete analysis utilizing the scattering matrix method is also used to compare the above calculation results which neglect multiple reflections between subslab interfaces. Broadband absorption of electromagnetic waves can be achieved by changing the magnetic field strength and plasma density. More than 90% of the electromagnetic wave power can be absorbed in a magnetized nonuniform plasma slab with width of 12 cm and the absorption bandwidth can range from 1 to 20 GHz with different plasma parameters and external magnetic field strengths.     

Basic characteristics of an atmospheric pressure rf generated plasma jet

A plasma jet has been developed which operates using radio frequency (rf) power and produces a stable homogeneous discharge at atmospheric pressure. Its discharge characteristics, especially the dependence of stable discharge operating range on the feed gas, were studied, and the electric parameters such as RMS current, RMS voltage and reflected power were obtained with different gas flows. These studies indicate that there is an optimum range of operation of the plasma jet for a filling with a gas mixture of He and O_2. Two "failure" modes of the discharge are identified. One is a filamentary arc when the input power is raised above a critical level, another is that the discharge disappears gradually as the addition of O_2 approaches 3.2%. Possible explanations for the two failure modes have been given. The current and voltage waveform measurements show that there is a clear phase shift between normal and failure modes. In addition, I－V curves as a function of pure helium and for 1% addition of oxygen have been studied.     

L-band tunable multiwavelength fiber laser using an unpumped polarization maintaining an erbium-ytterbium double-clad fiber-loop mirror

An L-band tunable multiwavelength source is newly proposed and demonstrated employing an unpumped polarization maintaining an erbium-ytterbium codoped double-clad fiber (PM-EYDF) loop mirror in a semiconductor optical amplifier-based fiber-ring laser. This is achieved by only adjusting the polarization controller in the loop mirror for the birefringence of the PM-EYDF, which is polarization dependent, and which originates from the fact that the traversing signal with a different polarization state absorbed by the PM-EYDF changes its effective birefringence. A similar behavior also happens when the traversing signal power is varied. The multiwavelength operation with the tunable range as large as the comb spacing of the transmission spectrum of the PM-EYDF loop mirror is successfully accomplished.