Al—Mg MMH溶胶和纳土悬浮体的相互作用机理

通过流变参数、电泳淌度和ｐＨ值的测定，研究了无机盐（ＣａＣｌ２、ＫＣｌ、ＮａＣｌ）和ｐＨ值对铝镁混合金属氢氧化物与钠土悬浮体间相互作用的影响。发现随着混合金属氢氧化物含量的增加，钠土体系的ｐＨ值逐渐降低，而动切力（ＹＰ）先上升，经最大值后逐渐下降；当钠土体系为ＮａＣｌ所饱和时，相同混合金属氢氧化物加量下ＹＰ的上升幅度明显减小，在实验混合金属氢氧化物浓度范围内，ＹＰ未出现峰值。混合金属氢氧化物／钠土     

镁铝氢氧化物正电溶胶结构研究

镁铝氢氧化物正电溶胶结构研究韩书华，张春光，侯万国，孙德军，王果庭（山东大学胶体与界面化学研究所，济南，２５０１００）关键词镁铝氢氧化物，正电溶胶，共沉淀镁铝氢氧化物是一种层状的氢氧化物。Ｂｕｒｂａ等［１］提出将镁铝氢氧化物与钠质蒙脱土作用可得到抑制...     

Al-Mg MMH溶胶和钠土悬浮体的相互作用机理

通过流变参数、电泳淌度和pH值的测定,研究了无机盐(CaCl₂、KCl、NaCl)和pH值对铝镁混合金属氢氧化物与钠土悬浮体间相互作用的影响。发现随着混合金属氢氧化物含量的增加,钠土体系的pH值逐渐降低,而动切力(YP)先上升,经最大值后逐渐下降;当钠土体系为NaCl所饱和时,相同混合金属氢氧化物加量下YP的上升幅度明显减小,在实验混合金属氢氧化物浓度范围内,YP未出现峰值。混合金属氢氧化物/钠土体系的YP随pH值的变化曲线呈抛物线形,加入相同浓度的无机盐,△YP、△pH(绝对值)按CaCl₂KCl～NaCl次序递减。     

镁铝氢氧化物正电溶胶的制备

对镁铝氢氧化物制备的反应条件进行了研究，结果表明：溶胶中镁铝比随混合溶液中镁铝比的增加而增加到一极限值(Mg/Al=2)。随着制备时的镁铝比的增加，溶胶的固含量增加，其产率下降，但ζ电位先上升而后下降。在溶液中镁铝比大于2∶1时，溶胶中只有镁铝氢氧化物。随温度的升高，在胶溶过程中颗粒增大，为六角片状微晶。     

铝镁混合金属氢氧化物溶胶阴离子交换性能研究

本文研究了电解质对铝镁混合金属氢氧化物（Ａｌ－ＭｇＭＭＨ）溶胶粒子中Ｃｌ－和ＯＨ－的阴离子交换性能。在所研究的电解质ＮａＮＯ３，ＨＣＯＯＮａ，ＣＨ３ＣＯＯＮａ，Ｎａ２ＣＯ３，Ｎａ２ＳＯ４和Ｎａ３ＰＯ４中，发现高价阴离子的交换能力大于低价阴离子的交换能力，无机阴离子的交换能力大于有机阴离子的交换能力。所研究Ａｌ－ＭｇＭＭＨ溶胶粒子的阴离子交换容量为２．８２ｍｍｏｌ／ｇ，比粘土粒子的阳离子交换容量大得多。     

层状复合金属氢氧化物：结构、性质及其应用

本文评述层状复合金属氢氧化物(layered double hydroxides，LDHs)的化学及其应用。层状复合金属氢氧化物具有结合紧密的氢氧化物层和处于层间的阴离子，其比较突出的化学性质是可逆的阴离子交换和热分解性质。不过，因为受到氢氧化物层的局限，处于层间的阴离子表现出的特殊化学性质近年来也越来越受到重视。利用上述三个方面的性质，人们发掘了层状复合金属氢氧化物在材料(包括有机无机复合材料)制备、离子交换与有害阴离子脱除、异构体化学分离、化学反应控制、阻燃材料、活性分子储存与缓释、局部化学反应合成、催化剂及催化剂载体等方面的应用。     

无机电解质及聚合物对Mg-Al混合金属氢氧化物—高岭土分散体系触变性的影响

类水滑石;流变学;无机电解质及聚合物对Mg-Al混合金属氢氧化物—高岭土分散体系触变性的影响     

阳离子膨润土制备和性质的研究

用插入法将混合金属层状氢氧化物正电胶体沉淀于膨润土矿物晶体层间,合成了阳离子膨润土,其最高ζ电位40mV。研究了温度、Mg~(2+)浓度、pH值及无机电解质等对阳离子土ζ电位的影响。发现该阳离子膨润土的悬浮体与不同价数的阴离子作用符合Schulze-Hardy规则,并对Al~(3+)有特性吸附,而对Mg~(2+)则没有。     

电位滴定判断二元金属氢氧化物的复合化

尖晶石型纳米复合金属氧化物目前主要的合成方法还是共沉淀法 [1,2 ] .但是此种方法常因不能准确掌握共沉淀的 p H范围 ,而出现组分金属离子偏析 ,难制得不含杂相的纯净复合金属氧化物纳米微粒[3] .混合金属离子能否形成复合氢氧化物 ,在什么条件下形成 ,这方面的研究还未见报道 .电位滴定法通常是研究单一金属离子的水解或氢氧化物生成的有效方法 [4 ,5] ,为此 ,我们以 Al3+、Fe3+分别与 Ni2 +、Zn2 +、Cu2 +等金属离子形成的二元金属混和溶液为对象 ,使用自动电位滴定仪测定这些混合体系的电位滴定曲线 ,并通过与相应的单一金属离子的…     

以含铬类水滑石型层状化合物为模板制备硫化物半导体纳米晶

采用类水滑石型混合金属氢氧化物(CdCr-LDH和ZnCdCr-LDH)为前驱体, 通过气-固反应方法, 制备了根植于层状氢氧化物层板中的硫化镉纳米晶和硫化镉/硫化锌复合纳米晶, 通过改变前驱体(CdCr-LDH)中镉和铬的摩尔比可以调控硫化镉纳米晶的粒径.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.