宽光谱高衍射效率脉宽压缩光栅设计和性能分析

基于飞秒激光对脉宽压缩光栅宽光谱和高衍射效率的要求,提出了一种金属介质膜结构的宽光谱高衍射效率脉宽压缩光栅,该光栅由基底、金属介质膜和表面浮雕结构组成.为获得宽光谱高衍射效率的脉宽压缩光栅,采用严格耦合波理论对金属介质膜光栅的结构参数进行优化设计.数值分析表明当金属介质光栅的槽深、剩余厚度、占空比和入射角分别为272 ...     

基于严格耦合波理论的多层介质膜光栅衍射特性分析

基于严格耦合波理论建立了多层介质膜光栅的衍射机理模型,给出了TE波自准直条件下多层介质膜光栅衍射效率的表达式.以－1级衍射效率为评价函数,分析了表面浮雕结构分别为HfO₂和SiO₂材料的介质膜光栅获得衍射效率优于96%的结构参数.数值计算表明,顶层材料为HfO₂的介质膜光栅具有更宽的结构选择范围.最后分析了介质膜光栅的制备容差和允许的入射角度范围. 关键词： 衍射效率 多层介质膜光栅 严格耦合波理论     

基于严格耦合波理论的宽光谱金属介质膜光栅衍射特性分析

基于严格耦合波理论建立了金属介质膜光栅的衍射机理模型,给出了TE模式金属介质膜光栅衍射效率的表达式.以-1级衍射效率和工作带宽为评价函数,对金属介质膜光栅的表面浮雕结构进行了优化设计.对于800 nm和1053 nm为中心的TE波,设计的金属介质膜光栅-1级衍射效率优于97%的工作带宽分别达到130 nm和150 nm,最后讨论了设计的宽光谱高衍射效率金属介质膜光栅的制备工艺容差.此研究对于提高脉宽压缩光栅的性能具有重要的意义. 关键词： 衍射效率 金属介质膜光栅 严格耦合波理论     

亚波长介质偏振分束光栅的衍射特性

 采用严格耦合波理论并结合矩阵LU分解法,分析了亚波长介质光栅的刻槽深度、占空比、入射角、入射波长等参数对TE偏振和TM偏振0级衍射效率的影响。结果表明:在1 550 nm波长处,出现瑞利反常现象。由此提出利用瑞利反常现象设计工作波长为1 550 nm的偏振分束光栅,通过优化设计确定了最佳设计参数,即光栅周期为l0/2,瑞利入射角为30°,刻槽深为0.9l0,占空比为0.5。结果表明,参数优化后的偏振分束光栅可以使TE偏振0级反射波和TM偏振0级透射波同时达到近100%的衍射效率。     

飞秒激光用多层介质膜脉宽压缩光栅的设计

以薄膜光学的干涉理论和衍射光学的傅里叶模式理论为基础，给出了0.8μm飞秒激光器用多层介质膜脉宽压缩光栅的理论设计；设计采用H3L(HL)^9H0.5L2.4H的多层介质膜为基底，当刻蚀后表面浮雕结构的占宽比为0.35，线密度为1480线/mm，槽深为0.2μm，顶层HfO₂的剩余厚度为0.15μm时，对于Littrow角度(36.7°)和TE波模式入射的衍射光栅其-1级衍射效率达到95％以上. 关键词： 飞秒激光 脉宽压缩光栅 多层介质膜     

多层介质膜脉宽压缩光栅的严格矢量分析

用于展宽和压缩激光脉冲的多层膜脉宽压缩光栅是由多层介质高反膜和位于其顶层的浮雕光栅构成。以设计的高反射多层膜为基础,利用傅里叶模式理论分析了其衍射场分布,给出了TE波自准直角入射的使用条件下,多层介质膜脉宽压缩光栅衍射效率的表达式。以-1级衍射效率为评价函数,分别讨论了HfO2和SiO2为顶层材料时,多层膜脉宽压缩光栅-1级衍射效率高于0.95的光栅结构参量范围。结果表明,在该条件下,选择HfO2为顶层材料时,光栅结构参量有较大的取值范围。给出了优化的光栅结构参量,并分析了光栅制作误差及其使用条件的宽容度,对光栅制作工艺和使用具有一定的指导意义。     

亚波长闪耀光栅矢量衍射效率计算

将矢量衍射数值算法—严格耦合波分析用于精确计算亚波长闪耀光栅的衍射效率,并分析其衍射特性。建立了闪耀光栅的电磁介质模型,并将楔形不规则结构简化为多层矩形光栅结构,通过电磁场的介质分布建立严格耦合波方程。根据边界条件求解出各层的电磁场分布,再通过增透矩阵方法将各层电磁场依次迭代,求解出了整个结构的衍射效率。计算分析显示,对闪耀角为11.3°、周期为500 nm的金属铝闪耀光栅可以得到高于90%的衍射效率和相应的闪耀级次。实验表明这种矢量衍射数值算法具有较高的准确性,可以推广应用于高致密刻线复杂光栅的衍射计算分析。     

基于等效折射率人工剪裁的宽带高效光栅耦合器

利用不同占空比的亚波长结构剪裁光栅槽的等效折射率来改变光栅的衍射特性实现衍射输出光束与单模光纤之间的模式匹配,通过优化埋氧化层厚度和集成底部金反射镜,可以改善光栅耦合器弱的方向性,从而设计出用于SOI波导与光纤之间高效率耦合的光栅耦合器。采用本征模展开方法,模拟了光栅耦合器随剪裁的光栅槽等效折射率变化的相关特性,在SOI波导和单模光纤之间对波长为1550nm的光获得了最高93.1%的耦合效率,3dB带宽为82nm。     

13.4nm软X射线干涉光刻透射光栅的优化设计

基于严格的矢量耦合波方法,结合纳米级光栅实际制作工艺,定量分析了在13.4 nm软X射线(TE偏振)正入射条件下,光栅材料、厚度、占空比、梯形浮雕底角大小等因素对光栅一级衍射效率的影响.结果表明,在此波段处,Si3N4、Cr、Au浮雕的相位作用对光栅衍射起重要影响,其中非金属材料Si3N4比金属材料Cr、Au的相位作用更明显.最后优化得到了用Si(或Si3N4)做衬底的si3N4、Cr、Au光栅,分析结果显示,其一级衍射效率优于目前用于13.4 nm软X射线干涉光刻的Cr、Si3N4复合光栅.     

利用陷光结构增加硅薄膜太阳能电池的吸收效率

提出了一种含有光锥光子晶体防反射层和四棱锥光栅背反射层的a-Si薄膜太阳能电池结构,吸收层厚1μm,总厚度为1.45μm。根据光子晶体及亚波长光栅的衍射特性,利用严格耦合波方法对器件参数进行了优化。计算结果表明:当光锥结构倾角θ=72°、晶格常数T1=1 200 nm、介质底半径r=100 nm时,防反射层的透射率较高,在300~600 nm波长范围内,该薄膜太阳能电池的吸收效率比不含防反射层电池提高了11.54%;当四棱锥光栅结构周期L=1.2μm、占空比f=0.38、槽深h5=560 nm时,背反射层的反射效果较好,在600~850 nm波长范围内,电池的吸收效率提高了3.75%。所设计的薄膜电池结构在波长为300~750 nm、入射角为0°~75°范围内的吸收效率均在80%以上,平均吸收效率达92%,满足太阳电池对宽频谱、广角度的光俘获的要求。     

Broadband and high efficiency metal multi-layer dielectric grating based on non-quarter wave coatings as reflective mirror

This article deals with designing broadband and high efficiency metal multi-layer dielectric grating (MMDG) used to compress and stretch ultra-short laser pulse. The diffraction characteristics of MMDG are analysed with the method of rigorous coupled-wave method. The multi-layer dielectric used as reflective mirror is made up of non-quarter wave coatings. Taking the diffraction efficiency of the -1 order as the value of merit function, the parameters such as groove depth, residual thickness, duty cycle, and reflective mirror are optimized to obtain broadband and high diffraction efficiency. The optimized MMDG shows an ultra-broadband working spectrum with the average efficiency exceeding 97% over 160 nm wavelength centred at 1053 nm and TE polarization. The optimized MMDG should be useful for chirped pulse amplification.     

Broadband and high efficiency metal multi-layer dielectric grating based on non-quarter-wave coatings as a reflective mirror

This article deals with designing a broadband and high efficiency metal multi-layer dielectric grating (MMDG) used to compress and stretch an ultrashort laser pulse. The diffraction characteristics of the MMDG are analysed by using the rigorous coupled-wave method. The multi-layer dielectric used as the reflective mirror is made up of non- quarter-wave coatings. Taking the diffraction efficiency of the 1 order as the value of merit function, the parameters such as groove depth, residual thickness, duty cycle, and reflective mirror are optimized to obtain broadband and high diffraction efficiency. The optimized MMDG shows an ultra-broadband working spectrum with the average efficiency exceeding 97% over 160 nm wavelength centred at 1053 nm and TE polarization. The optimized MMDG should be useful for chirped pulse amplification.     

基于多层介质膜光栅的谱合成系统光束特性分析

针对多层介质膜光栅在光束谱合成系统中的应用, 利用光线追迹方法, 建立了基于多层介质膜光栅的谱合成系统光传输模型. 多层介质膜光栅引入的相位调制包括浮雕表面上光程差与浮雕结构光程差两部分, 且受到光栅槽深、占空比和光束入射角等因素的影响. 利用衍射积分方法和光束非相干叠加原理, 计算模拟了基于多层介质膜光栅的谱合成系统的合成光束光强分布. 在此基础上, 利用强度二阶矩方法分析了合成光束的光束质量, 并讨论了多层介质膜光栅的槽深、占空比和制作误差等因素对合成光束特性的影响. 结果表明: 改变多层介质膜光栅的槽深和占空比以及中心光束入射角会影响合成光束能量, 但不会影响合成光束的光束质量, 合成光束的光束质量始终保持与单个子光束的光束质量相当; 多层介质膜光栅的制作误差对合成光束的光束质量和能量均存在明显影响.     

软X射线位相型金透射光栅的设计与制作

根据衍射光栅的标量理论,计算并讨论了金透射光栅在软X波段衍射效率对光栅厚度和占宽比的依赖关系.结果表明,选择合适的光栅槽深和占宽比,高达 21.9%的衍射效率可能被获得,远高于振幅型光栅的+1级衍射效率10.14%.通过全息光刻与电镀转移技术制作的位相型金透射光栅由300nm的聚酰亚胺薄膜支撑,光栅槽深200nm,占宽比为0.55,周期为1μm,面积为20mm×5mm.在国家同步辐射装置上,测得其+1级透射衍射效率在波长λ=7.425nm时获得最大值,约为16%. 关键词： 透射位相光栅 全息光刻 电镀     

可见光波段双层浮雕型导模共振滤波器设计与分析

基于傅里叶模式理论分析了双层浮雕型导模共振光栅的共振效应,分别讨论了光栅的槽深、剩余厚度、周期以及填充系数对峰值反射率、带宽、旁带反射率的影响. 数据计算表明,欠刻蚀情形的误差宽容度远远优于过刻蚀情形,两者在光栅槽深相对误差小于15％的范围内,都能保证共振峰的衍射效率高于99.5%,在相同的误差范围内,共振峰线宽的相对误差将分别达到7％和60％,因此厚度误差集中反映在对共振线宽的改变上. 另外,光栅周期和填充系数的变化将明显改变共振峰中心波长和线宽. 关键词： 导模共振 平面波导 窄带滤波     

Metal-mirror-based grating for high-efficiency element in dense wavelength division multiplexing

It is desirable to obtain high efficiency with polarization-independence and wideband properties for incident wavelength. A metal-mirror-based grating is presented to diffract the incident wave into reflection orders with high efficiency for TE and TM polarization. The modal method and rigorous coupled-wave analysis (RCWA) are used together to optimize a metal-mirror-based grating effectively. From the analysis of the modal method, it is feasible to realize such a grating with the prescribed grating duty cycle and period. Accurate parameters of the grating depth and thickness of the connecting layer are optimized using RCWA. Compared with the reported binary simple grating, high efficiency can be improved greatly for the incident wavelength of 1550 nm in dense wavelength division multiplexing. The diffraction investigation indicates that a wideband property for incident wavelength can be obtained for such a novel metal-mirror-based grating.     

Connecting-layer-based polarizing beam splitter grating with high efficiency for both TE and TM polarizations

We describe a novel polarizing beam splitter (PBS) of transmission connecting-layer-based grating, which can show high efficiency for TE polarization in the ?1st order and TM polarization in the 0th order. According to the modal method, grating duty cycle and period are prescribed to obtain high efficiency for TM polarization. Using the rigorous coupled-wave analysis, grating depth and thickness of the connecting layer are optimized to achieve high efficiency for TE polarization. The presented PBS has advantages of wideband properties for incident wavelength and angle. Most importantly, the efficiency is improved greatly for TE polarization compared with the reported PBS based on fused-silica grating.