固体石蜡碳糊硅钼酸电极的研制及应用

将固体石蜡作粘合剂的碳糊电极在１０＾－４ｍｏｌ／Ｌ硅钼杂多酸溶液中活化后，其表面形成了杂多酸薄膜。电极对浓度为２．０×１０＾－５￣１．０×１０＾－２ｍｏｌ／Ｌ范围的硅钼杂多酸有所斯特响应；斜率为２９．０ｍＶ，从而可间接测定硅。该电极选择性、稳定性较好，响应快，已用于矿泉水样中偏硅酸含量测定。     

流动注射速差动力学化学发光分析Ⅱ微量磷的快速测定

本文根据磷钼杂多酸可直接氧化Ｌｕｍｉｎｏｌ产生化学发光的特性，建立了磷的流动注射化学发光分析方法。利用磷钼杂多酸、硅钼杂多酸、砷钼杂多酸形成速率的差异，在磷、硅、砷共存时，可不经任何分离，实现对水样和钢样中磷的快速测定。该法检出限为３．６×１０－５ｇ／Ｌ，线性范围２．０×１０－４～１．０×１０－２ｇ／Ｌ，相对标准偏差为１．８％（磷浓度１．０×１０－３ｇ／Ｌ；ｎ＝１１次）。采样频率４５样／ｈ。     

流动注射示差动力学化学发光法测定微量硅

根据硅钼杂多酸氧化Ｌｕｍｉｎｏｌ产生化学发光的性质，以及硅钼杂多酸与磷钼杂多酸形成速度的差异，采用停流技术，在硅磷共存时，不经分离，实现了对和钢样中硅的选择性测定。该法检出限为２．０×１０＾－８ｇ／ｍＬ，线性范围１．０×１０＾－７－１．０×１０＾－５ｇ／ｍＬ，相对标准偏差为２．８％。     

大量锆存在下铪镧钼杂多酸—耐尔蓝体系测定给

本文研究了耐尔蓝（ＮＢ）－给镧钼杂多酸（ＨｆＬａＭｏ－聚乙烯醇（ＰＶＡ）体系测定铪的超高灵敏光度法。在ＰＶＡ存在下，铪，镧和钼酸铵形成杂多酸，继而与耐尔蓝形成离子缔合物。其适宜条件为〔ＨＣｌｏ４〕＝１．２ｍｏｌ／Ｌ，〔Ｌａ×３＋〕＝２．９×１０＾－７ｍｏｌ／Ｌ，〔ＭｏＯ４×２－〕＝１．１×１０＾－３ｍｏｌ／Ｌ，〔ＮＢ〕＝２．７×１０＾－６ｍｏｌ／Ｌ，ＰＶＡ０．０８％。离子缔合物的最大吸收波长在５９     

硅钼杂多阴离子薄膜修饰电极线性扫描伏安法测定黑液中要溶性硅

本报导了以玻碳电极为基体的１∶１２硅钼杂多阴离子薄膜化学修，铈电极的制备及其电化学特性。并应用于导数伏安法测定。在４．０×１０＾－３ｍｏｌ／Ｌ９ＮＨ４）６Ｍｏ７Ｏ２４－６６．８×１０＾－２ｍｏｌ／ＬＮａ３Ｃｉｔ－０．４８ｍｏｌ／Ｌ ＮＨＯ３体系中，硅浓度在８．３×１０＾－７～１．７×１０＾－３ｍｏｌ／Ｌ。对可溶性硅（以ＳｉＯ２计）为２４５．０５ｍｇ／Ｌ的黑液，稀释１０倍后，取２．００ｍＬ平行测定     

钼—桑色素的极谱波及其用于钨精矿中钼的测定

本提出了测定钼的新极谱体系，最佳底液条件为ｐＨ２．１的盐酸－２．３７×１０＾－６ｍｏｌ／Ｌ桑色素－０．１７２ｍｏｌ／Ｌ氯酸钠。极谱波峰电位为－０．４３Ｖ（ｖｓ．ＳＣＥ），钼（Ⅵ）浓度在１．０４×１０＾－９￣４．５９×１０＾－８ｍｏｌ／Ｌ范围内与波高有线性关系，检出限３．６７×１０＾－１０ｍｏｌ／Ｌ。方法简便，快速、准确，并已直接应用于钨精矿中微量钼的测定。     

硅钼杂多阴离子薄膜修饰电极线性扫描伏安法测定黑液中可溶性硅

本文报导了以玻碳电极为基体的１：１２硅钼杂多阴离子薄膜化学修铈电极的制备及其电化学特性。并应用于导数伏安法测定。在４．０×１０￣（－３）ｍ０ｌ／Ｌ（ＮＨ＿４）＿６ＭＯ＿７Ｏ＿（２４）－６．８×１０￣（－２）ｍｏｌ／ＬＮａ＿３Ｃｉｔ－０．４８ｍｏｌ／ＬＮＨＯ＿３体系中，硅浓度在８．３×１０￣（－７）～１．７×１０￣（－３）ｍｏｌ／Ｌ范围内与峰电流呈良好线性关系，检测限为８．０×１０￣（－７）ｍｏｌ／Ｌ。对可溶性硅（以ＳｉＯ＿２计）为２４５．０５ｍｇ／Ｌ的黑液，稀释１０倍后，取２．００ｍＬ平行测定９次，ＲＳＤ为０．５８％，加标回收率在９７．３％～１０４．４％间。     

分光光度法同时测定中草药中的钼和铜

本文建立了在混合显色剂（ＰＦ＋ＰＡＮ）的胶束体系中，利用分光光度法同时测定中草药中的钼和铜。实验表明：在混合体系中，钼量在０～１０μｇ／２５ｍＬ，铜量在０～５０μｇ／２５ｍＬ的范围内符合比尔定律，ε′Ｍｏ＝９．２×１０４Ｌ·ｍｏｌ－１·ｃｍ－１；ε′Ｃｎ＝１．５×１０４Ｌ·ｍｏｌ－１·ｃｍ－１。该法用于中草药样品的分析，结果满意，回收率可达９２～１１１％。     

钍钼杂多酸—丁基罗丹明B测定岩矿口痕量钍

本文报道了一个灵敏度高，选择性好的测定痕量钍的新光度分析法。在聚乙烯醇存在下，钍钼杂多酸和丁基罗丹明Ｂ形成离子缔合物，其适宜条件为ＣＨＣｌＯ４＝１．３ＭＯＬ／Ｌ，ＣＭｏＯ＾２－４＝６．８×１０＾－４ｍｏｌ／Ｌ，ＣＢＲＢ＝２．７×１０＾－５ｍｏｌ／Ｌ，ＰＶＡ０．０８％。     

丁基罗丹明B-铜钨杂多酸光度法测定微量铜

在聚乙烯醇（ＰＶＡ）存在下，丁基罗丹明Ｂ（ＢＲＢ）与铜钨杂多酸形成离子缔合物。缔合物的形成条件为ｃＨ２ＳＯ４＝１．２ｍｏｌ／Ｌ，ｃＷＯ２－４＝６．１×１０－５ｍｏｌ／Ｌ，ｃＢＲＢ＝３．８×１０－５ｍｏｌ／Ｌ和ＰＶＡ０．０８％。缔合物的最大吸收波长位于５７０ｎｍ，摩尔吸光系数ε＝１．６６×１０６Ｌ·ｍｏｌ－１·ｃｍ－１，铜量在每２５ｍＬ０～０．５μｇ范围内服从比耳定律，检测限为每ｍＬ０．６５ｎｇ（ｎ＝１２），对每ｍＬ１８ｎｇＣｕ测定的ＲＳＤ为０．８５％（ｎ＝１０）。缔合物至少稳定１５０ｈ，其摩尔比为Ｃｕ∶Ｗ∶ＢＲＢ＝１∶１２∶５，红外图谱表明铜钨杂多酸具有Ｋｅｇｇｉｎ结构。考察了４０多种共存离子的影响，大多数常见元素不干扰。本法已用于天然水、自来水、降水、人发、中药和蔬菜中铜的测定，结果满意。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.