Preparation of polybenzoxazole fibers via electrospinning and postspun thermal cyclization of polyhydroxyamide

Polybenzoxazole (PBO) fibers with a submicron diameter were successfully prepared by electrospinning its precursor, polyhydroxyamide (PHA), solutions to obtain the PHA fibers first, followed by appropriate thermal treatments for cyclization reaction. BisAPAF‐IC PHA with two different molecular weights (MWs) were synthesized from a low temperature polymerization of 2,2′‐bis(3‐amino‐4‐hydroxyphenyl) hexafluoropropane (BisAPAF) and isophthaloyl chloride (IC). Using dimethylacetamide (DMAc) and tetrahydrofuran (THF), solvent effects on the electrospinnability of PHA solutions were investigated. For balancing the solution properties, it was found that DMAc/THF mixture with a weight ratio of 1/9 was the best cosolvent to prepare smooth PHA fibers; uniform PHA fibers with a diameter of 325–720 nm were obtained by using 20 wt % PHA/(DMAc/THF) solutions. For a fixed PHA concentration, solutions with a lower MW of PHA yielded thinner electrospun fibers under the same electrospinning condition. After obtaining the electrospun BisAPAF‐IC PHA fibers, subsequent thermal cyclization up to 350 °C produced the corresponding thermally stable BisAPAF‐IC PBO fibers with a diameter of 305–645 nm. The structure of the precursor fibers and the fully cyclized fibers were characterized by FTIR. For the cyclized BisAPAF‐IC PBO fibers, thermogravimetric analysis showed a 5% weight loss temperature at 523 °C in nitrogen atmosphere. The interconnected fiber structure in the BisAPAF‐IC PBO fiber mats was irrelevant to the curing process, but resulted from the jet merging during the whipping process as revealed by the high speed camera images. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8159–8169, 2008     

新型含磷和氟聚芳醚的制备、表征及性能

通过分子设计, 成功合成了一种含有三苯基膦结构的二氟单体--4,4’-二氟二苯苯磷氧(BFPPO). 在碱催化条件下, BFPPO与2-双-(4-羟苯基)六氟丙烷(六氟双酚A)缩聚得到一种新型含三苯基膦结构的聚芳醚材料(6F-PAEPO). 使用FTIR,1H NMR, 31P NMR, 和16F NMR等表征手段确定了聚合物的结构, 聚合物表现出良好的热稳定性、有机可溶性、机械性能和光透过性能, 其中聚合物的玻璃化转变温度高达211℃, 空气气氛和氮气气氛下5%热失重温度分别为512℃和523℃, 聚合物薄膜的最大光透过率超过80%. 尤其, 聚合物由于主链中三苯基磷氧结构的存在, 表现出了优异的阻燃性能, 有限氧指数(LOI)达到39.9%.     

Novel positive‐working and aqueous‐base‐developable photosensitive poly(imide benzoxazole) precursor

A novel positive‐working and aqueous‐base‐developable photosensitive poly(imide benzoxazole) precursor based on a poly(amic acid hydroxyamide) bearing phenolic hydroxyl groups and carboxylic acid groups, a diazonaphthoquinone (DNQ) photosensitive compound, and a solvent was developed. Poly(amic acid hydroxyamide) was prepared through the polymerization of 2,2‐bis(3‐amino‐4‐hydroxyphenyl)hexafluoropropane, trimellitic anhydride chloride, and 4,4′‐oxydibenzoyl chloride. Subsequently, the thermal cyclization of the poly(amic acid hydroxyamide) precursor at 350 °C produced the corresponding poly(imide benzoxazole). The inherent viscosity of the precursor polymer was 0.17 dL/g. The cyclized poly(imide benzoxazole) showed a high glass‐transition temperature of 372 °C and 5% weight loss temperatures of 535 °C in nitrogen and 509 °C in air. The structures of the precursor polymer and the fully cyclized polymer were characterized with Fourier transform infrared and ¹H NMR. The photosensitive polyimide precursor containing 25 wt % DNQ photoactive compound showed a sensitivity of 256 mJ/cm² and a contrast of 1.14 in a 3‐μm film with a 0.6 wt % tetramethylammonium hydroxide developer. A pattern with a resolution of 5 μm was obtained from this composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5990–5998, 2004     

刚性聚芳醚腈合成与性能研究

用２，６ 二氟苯甲腈和间苯二酚为原料，在碱性条件下，于非质子极性溶剂中，通过溶液高温缩聚法制备聚芳醚腈［Ｐｏｌｙ（ｃｙａｎｏａｒｙｌｅｔｈｅｒ）ＰＣＥ］．并用ＩＲ、ＤＳＣ、ＴＧ、ＷＡＸＤ等手段对其结构及热性能、结晶行为进行了研究．结果表明，ＰＣＥ高聚物不仅具备较好的耐高温和耐热老化性能，而且具有较好的结晶性能．同时，用对比的方法，对ＰＣＥ的晶体结构进行了初步的探讨．     

4,4′-二(2-甲基苯氧基)二苯砜/1,4-二苯氧基苯/对苯二甲酰氯三元共缩聚物的合成与表征

通过加入第三单体4,4′-二(2-甲基苯氧基)二苯砜与1,4-二苯氧基苯(DPB)和对苯二甲酰氯(TPC)进行三元无规共聚,合成了一系列分子主链带砜基和主链芳环上含甲基侧基的聚(芳醚砜醚酮酮-co-醚醚酮酮)共聚物,并用FT-IR、DSC、WAXD和TG对其进行了表征.结果表明,共聚物的玻璃化转变温度随着第三单体摩尔含量的增加而逐渐升高,熔融温度则逐渐降低,当其摩尔含量为10%~30%时,共聚物具有优良的耐热性能及耐溶剂、耐酸碱性能.     

含芳基均三嗪环耐高温低聚酰亚胺的合成与性能

通过调控聚合单体的摩尔配比,合成了一系列新型的不同分子链长度的邻苯二甲腈封端含二氮杂萘酮联苯结构低聚酰亚胺,通过FTIR、1H-NMR、WAXD和元素分析对其结构进行表征.以4,4′-二氨基二苯砜为催化剂,低聚物经常压下固化交联后,得到含芳基均三嗪环结构的热固性聚酰亚胺.低聚物表现了良好的溶解性能,可溶于N-甲基-2-...     

High‐density polyethylene fractionation with supercritical propane

During the development of column extraction techniques, two methods of separation were identified. The first method is based on altering polymer solubility by varying the ratio of solvent in a solvent/nonsolvent mixture at a constant temperature above the polymer melting point (gradient solvent elution fractionation). This method fractionates polymers according to molecular weight. The second method is based on altering polymer solubility by varying solvent temperature (temperature rising elution fractionation—TREF). TREF fractionates semicrystalline polymers with respect to their crystallizability, independently of molecular weight effects. In the present article, supercritical propane will be used to fractionate a high‐density polyethylene sample by molecular weight and short chain branching. The main advantage of supercritical fluid fractionation is that large polymer fractions with narrow molecular weight distributions (isothermal fractionation) or narrow short chain branching distributions (isobaric fractionation) can be obtained without using hazardous organic chlorinated solvents. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 553–560, 1999     

Synthesis and characterization of novel aromatic poly(imide–benzoxazole) copolymers

New poly(imide–benzoxazole) copolymers were prepared directly from a dianhydride, a diacid chloride, and a bis(o‐diaminophenol) monomer in a two‐step method. In the first step, poly(amic acid–hydroxyamide) precursors were synthesized by low‐temperature solution polymerization in an organic solvent. Subsequently, the thermal cyclodehydration of the poly(amic acid–hydroxyamide) precursors at 350 °C produced the corresponding poly(imide–benzoxazole) copolymers. The inherent viscosities of the precursor polymers were around 0.19–0.33 dL/g. The cyclized poly(imide–benzoxazole) copolymers had glass‐transition temperatures in the range of 331–377 °C. The 5% weight loss temperatures ranged from 524 to 535 °C in nitrogen and from 500 to 514 °C in air. The poly(imide–benzoxazole) copolymers were amorphous, as evidenced by the wide‐angle X‐ray diffraction measurements. The structures of the precursor copolymers and the fully cyclized copolymers were characterized by Fourier transform infrared, ¹H NMR, and elemental analysis. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6020–6027, 2005     

聚全氟三嗪的合成研究Ⅱ.2-三氟甲基-4,6-二(4′-碘-2′-氧杂六氟丁基)-1,3,5-三嗪的聚合研究

本文研究三嗪单体Ⅰ的纯化和聚合,粗品单体含有化合物Ⅱ,Ⅲ和Ⅳ等杂质,可用低温结晶并经氧化铝短柱过滤的方法除去。Ⅰ在金属汞存在下,经紫外线照射,在溶剂中或无溶剂情况下聚合。所得聚合物Ⅴ具有较好的耐热性能,其主链上几乎不存在未成环的薄弱链节,Ⅴ的平均分子量为1.33—2.0×10~4(聚合度为27—42),在氮气中失重10％。时的温度为340℃。     

Synthesis of ultra-thin films of aromatic polymers at air/water interface

Ultra-thin films of and precursor polymers for polybenzimidazole (PBI), polybenzoxazole (PBO), or polybenzothiazole (PBT) were formed at air/water interface by spreading monomers and then polymerizing on the water surface. These thin films could be deposited onto appropriate substrates by using the LB method of horizontal lifting. Moreover, the heat-treatment of the built-up films of the precursor polymers of PBI, PBO, and PBT formed the ultra-thin films of high temperature polymers. The resulting ultra-thin films had uniform and controllable thickness, but remained fairly stable when subjected to temperature up to 300°C. They also had good solvent resistance.     

双噁唑啉对聚碳酸1,2-环己二酯的扩链研究

采用马来酸酐封端聚碳酸1,2-环己二酯(PCHC),使其末端羟基转变为端羧基(MA-PCHC),并以2,2'-双-(2-噁唑啉)(BOZ)为扩链剂进行扩链反应.研究发现,BOZ与MA-PCHC中的羧基等摩尔情况下,扩链效果最佳.扩链后的PCHC的数均分子量从扩链前的5.6×104增长到12.4×104.扩链后的PCHC...     

含亚甲基和双二氮杂萘酮结构的聚芳酮的合成与性能

聚芳醚酮是一类重要的具有优异综合性能的工程塑料 ,它具有高的热稳定性、尺寸稳定性、耐溶剂性、好的加工性能和电性能 ,因而它经常作为复合材料的基质、粘合剂等被广泛的应用于航空、航天和电子等领域 .近几十年来 ,人们付出了很大的努力去开发聚芳醚酮新品种[1,2 ] .本研究组以 4 (4′ 羟基苯氧基 ) 2 ,3 二氮杂萘 1 (2Ｈ) 酮为缩聚单体制备了一系列的性能优良的聚芳醚酮[3～ 6] ,在主链中引入高密度的氮杂萘酮结构是获得高热稳定性和良好溶解性的重要途径 .由单体中含有更多的氮杂萘酮结构获得可溶解且耐温等级更高的聚芳酮是人们期…     

聚异酰亚胺树脂合成条件的优化

采用不同溶剂制备了苯乙炔基封端的聚异酰亚胺树脂,探讨了不同处理温度对聚异酰亚胺树脂(PⅡ)和相应的聚酰亚胺树脂(PⅠ)的熔体粘度及溶解性的影响。结果表明,不同处理温度对PⅡ的熔体黏度影响不大,但对溶解性有一定的影响,PⅡ在NMP和THF中具有良好的溶解性能。在相同处理温度条件下,PⅡ的熔体黏度低于PⅠ。随处理温度的增加,PⅡ低聚物的T5%随之增加,PⅡ在110℃处理的T5%为208℃,150℃处理的T5%为323℃,180℃处理的T5%为382℃,PⅡ固化后的T5%为550℃,显示出较优异的耐热性能。     

含三苯基膦聚醚醚酮酮的结构与性能

以双[4-(对氟苯甲酰基)苯基]苯基氧化膦和对苯二酚(HQ)为单体, 合成了新型主链含三苯基膦结构的聚醚醚酮酮, 并对聚合物的结构和性能进行了表征.     

一种含酚酞结构聚酰亚胺的合成及性能表征

通过酚酞的硝化和还原,得到了一种新型的含酞结构和酚羟基的二胺单体,通过二胺和4,4'-六氟亚异丙基二(邻苯二甲酸酐)(6FDA)缩聚并高温亚胺化,得到了相应的含酚羟基聚酰亚胺PI-HP.利用1H-NMR、FTIR、GPC及热分析表征了PI-HP的结构和热性能,利用紫外-可见光谱表征了其透明性.结果表明,PI-HP在部分极性有机溶剂中如DMF、THF、丙酮中具有良好的溶解性,具有较高的热稳定性并在可见光区域具有较好的透明性,其含羟基可进一步修饰用于制备各种功能材料.     

新型含氟耐高温聚吡咙--合成与性能研究

通过改进的Chichibabin反应合成了主链含有吡啶单元的新型含氟四胺单体 ,2 ,6 双 (3′ ,4′ 二氨基苯基 ) 4 (3″ ,5″ 双三氟甲苯基 )吡啶 (6FPA) .利用 6FPA与芳香族二酐单体 3,3′ ,4 ,4′ 二苯醚四羧酸二酐 (ODPA)通过两步热环化工艺制备了新型聚吡咙 (Polypyrrolone ,PPy)化合物 .对其所进行的各种性能测试结果表明 ,这种主链含有刚性吡啶结构、侧链带有含氟取代基的芳杂环高分子材料不仅保持了其固有的耐热性能 ,而且具有优良的成膜性能与耐水解性能 .例如其起始热分解温度为 5 5 8℃ ,失重 10 %温度为 5 91℃ ,72 0℃时的残余重量百分数为 6 8% ,玻璃化转变温度为 318℃ .PPy薄膜在 10 %NaOH水溶液中水解 7天仍具有良好的耐热性能与柔韧性 .     

Preparation and properties of polybenzoxazole-silica nanocomposites via sol-gel process

A novel organic/inorganic hybrid material has been prepared through the sol-gel process. A high temperature polymer, polybenzoxazole (PBO), was chosen as the organic phase due to its inherent low dielectric constant and low water absorption. The inorganic phase was generated via sol-gel reaction from a silica precursor, phenyltriethoxysilane (PTEOS). Due to the hydroxyl groups in the PBO precursor backbone and the water release during the cyclization of the precursor, the sol-gel reaction proceeded without the addition of water and any catalyst. After curing at 350 °C, we obtained the PBO/silica nanocomposites. From TEM and SEM photographs, the silica particles dispersed in the PBO matrix were nano-sized. With an addition of 100 wt% of PTEOS, the T_g of PBO was increased 35 °C. The dielectric constant of the hybrid materials increased with the increasing amount of PTEOS.     

功能化苯并咪唑类离子液体的合成及性质

合成了一系列由磺酸基、 羧基修饰的新型功能化苯并咪唑类离子液体, 采用IR, ¹H NMR, ¹³C NMR和ESI-MS对其结构进行了表征, 研究了化合物的热稳定性、 电导率以及室温下在各种溶剂中的溶解性等性质. 结果表明, 该类离子液体在 280 ℃以下基本没有失重, 热稳定性较好; 在水溶液浓度为1×10^-3 mol/L时, 随着温度的升高, 电导率几乎与温度呈正比增大; 能与大多数有机溶剂互溶, 溶解性随着溶剂极性的增加而增大.     

5-硝基-6-羟基-2-(对甲氧羰基苯基)苯并噁唑的合成

研究了以关键中间体4-氨基-6-硝基间苯二酚盐酸盐（ANR·HCl）和对苯二甲酸单甲酯（MTA）为原料,分别经酰氯化、缩合、环合分步或原位合成AB型新单体前体--4-（5-硝基-6-羟基-2-苯并噁唑基）苯甲酸甲酯（MNB）的技术。 反应优化条件：在甲基异丁基酮溶剂中,n(ANR·HCl)∶n(MTA)=1.00∶1.03,115 ℃缩合反应2.5 h;m(ANR·HCl)∶m(PPA)=1.00∶3.25的多聚磷酸(PPA),120 ℃环合8.5 h;MNB收率75.68%（以ANR·HCl计）,HPLC测定ω(MNB)=96.32%。 产物结构经¹H NMR和IR确证。     

STUDY ON THE SYNTHESIS OF POLYPERFLUOROTRIAZINE——The Synthesis and Polymerization of a Novel α,ω-Diiodoperfluorooxaalkyl s-Triazine Monomer*

In order to investigate synthetic route of polyperfluorotriazine elastomer, 2-trifluoromethyl4,6-bis(4′-iodo-2′-oxahexafluorobutyl)-1,3,5-triazine (1), a novel triazine monomer, was synthesized from 5-iodo-3-oxa-octafluoropentanesulfonyl fluoride (2) in eight-steps. 2 was reduced by potassium sulfite to the sulfinate (3), which was treated with hydriodic acid to yield 5-iodo-3oxa-hexafluoropentanoic acid (4). Compound 4 was transformed to 5-iodo-3-oxa-hexafluoropentanenitrile (7) through the corresponding ester 5 and amide 6. The desired product 1 was prepared by acylation-cyclodehydration of the imidoylamidine 9, obtained by condensation of the nitrile 7 with the amidine 8.The various methods for the esterification of perfluorocarboxylic acid were studied and a possible mechanism for the transformation of perfluorosulfinate to the corresponding perfluorocarboxylic acid by hydriodic acid was proposed.Crude 1 contained compounds 6, 11, 13, as impurities which were removed by low temperature crystallization followed by filtration through a short alumina column. The monomer 1 was polymerized by UV-irradiation in the presence of Hg with or without solvent. Polyperfluorooxaalkyl triazine 17 thus obtained showed good thermal stability. In the main chain of the polymer there was no weak unit of the uncyclized ring. Polymer 17 had an average molecular weight of ca. 1.33—2.0×10~4 (D. P.=27—42) and the temperature of 10% weight loss in nitrogen was 340℃.