Proposal of metal bellows-based fiber Bragg grating accelerometer

A metal bellows-based fiber Bragg grating(FBG) accelerometer is proposed and experimentally demonstrated. The optical fiber(containing the FBG) is pre-tensioned,and the two ends of the optical fiber are fixed directly from the shell to the inertial mass. In this design,the FBG is uniformly tensioned to obtain a constant strain distribution over it. By employing this configuration,the FBG always has a sharp reflection characteristic with no broadening in its reflection spectrum during wavelength shifting. Dy...     

基于近场光学的微球超分辨显微效应

在光学成像领域,由于受到衍射极限的限制,常规成像分辨率在200nm左右.科学的不断进步对更高分辨率有着迫切需求,如何突破这个极限来获得更高质量的高分辨率图像是热门研究领域.2011年提出了微球超显微技术:在原有的光学系统中,将直径几微米至几十微米的透明微球直接置于样品表面,就能够成倍提高传统光学显微镜的成像能力.微球超显微技术以其简单直接的特点,受到广泛关注.本文介绍了光学显微镜的研究背景以及国内外团队在微球超分辨显微技术方面的研究进展,包括通过在微球表面进行环刻同心环、中心遮挡和表面涂覆的方法来调节微球所产生的光子纳米喷射方面所开展的一系列研究,并进行了理论模拟和实验验证,进一步提升了微球的超分辨显微效应.最后,展望了今后微球超分辨显微技术的应用与发展方向.     

铁合金中微量钛元素的激光诱导击穿光谱研究

采用激光诱导击穿光谱对铁(Fe)合金中的钛元素(Ti)的含量进行测量。实验中激光器在最大能量输出(50 mJ),延时为1 μs时光谱信号的强度值最大。在此条件下,分别使用传统定标法和Fe Ⅰ 438.35 nm及Fe Ⅰ 427.12 nm两条谱线的内标法对铁合金中的Ti进行定量分析。内标法得到的拟合相关系数(r)分别为0.997 8和0.993 9,优于传统法得到的r(0.956 3)。提出了一种双谱线平均内标法,拟合得出r为0.998 4。同时,在浓度为0.063%～1.9%的范围内传统定标法测量的相对误差为23.7%,内标法的相对误差为6.0%,采用平均内标法后相对误差降为3.9%。最后,通过测量的Ti光谱计算了激光能量为50 mJ时所产生的等离子体温度为6 654.3 K,电子密度为1.072×1022 cm-3,并讨论了激光能量与烧蚀产生等离子体温度之间的关系。     

An Optical Labeling Scheme with Novel DPSK/PPM Orthogonal Modulation

A novel differential-phase-shift-keying （DPSK）/pulse-position-modulation （PPM） orthogonal modulation is pro- posed for optical labeling applications, with PPM data as the high-speed payload and DPSK signal as the optical label. The systematic setup for the proposed scheme and research on bit-error rate is presented. The results show that at the bit-error rate of 10-~, the power penalties for 70kin fiber transmission are in the range of 1-3 dB to DPSK label and 5-6 dB to PPM payload in our simulation system. This is under the condition that the large extinction ratio of 18-19 dB is used for the intensity modulators of the PPM payload, with a well received DPSK label. Thus the feasibility of the proposed scheme for all optical transmission networks is clearly verified.     

PEG聚合度对氧化铝造粒粉的性能影响

为制备适用于干压成型的氧化铝造粒粉,研究了PEG聚合度对氧化铝造粒粉微观形貌、流动性和松装密度的影响.结果表明PEG的聚合度对氧化铝浆料粘度影响显著,PEG2000-6000是较为理想的粘结剂选择,造粒粉的流动性与环境温度及湿度相关.采用正交实验设计,以造粒粉的流动性和松装密度为评价指标,对PEG聚合度、粘结剂添加量和固含量进行了优选,其影响顺序为PEG聚合度＞固含量＞粘结剂添加量.以优选参数PEG6000、添加量为4wt;、固含量为80wt;,制备了性能优良的氧化铝喷雾造粒粉.     

一种天然正长石的释光特性

应用RGB-3B型热释光仪和BG2003释光谱仪对一种正长石矿物的热释光和选频释光发光曲线进行测定,获得正长石的释光特性。研究表明：天然正长石的三个热释光峰峰温为148,197,310 ℃,辐照一定剂量后,出现197 ℃和263 ℃两个稳定的热释光峰。正长石的峰位温度随着增温速率的减小,向左移动。选频热释光290, 300, 310, 340, 400, 480 nm存在释光响应,选频绿光释光280, 290, 300, 310, 320, 400, 460, 480 nm存在释光响应,400 nm频道的光子计数随剂量的变化具有一定的线性关系,具有辐射剂量计的特性,具备释光测年的应用潜力。     

激光烧蚀硅基表面抗反射微结构的声信号监测

为了提高抗反射硅表面制备的加工质量、缩短研制周期,提出了一种基于时频域处理的面向激光加工过程的声波信号在线监测及分析方法。利用声信号的时频谱图分析了0～30 kHz内的声信号与激光烧蚀形成的表面微结构特征尺寸之间的相关性,具体分析了激光功率及加工次数对微结构深度及声信号各频率幅值变化的影响。以声信号作为输入,基于人工神经网络对加工质量进行预测。实验结果表明：通过监测激光加工时产生的声信号能够明确反映被烧蚀硅表面是否形成周期性微结构,且微结构宽度不同,其对应的声信号频率组成也不同。在微结构宽度固定的情况下,归一化后的声信号特征参数随微结构深度线性变化,且受到激光功率变化的影响忽略不计。以硅基表面5%的反射率作为加工质量分界线,采用人工神经网络对加工质量的预测结果与实际测量结果的准确率可以超过90%。结果表明：声波在线监测可以有效应用于评估表面加工质量,为抗反射硅表面制备过程的实时监测提供了理论依据。     

Pure annihilation type decays B0→Ds- K2+ and Bs→Da2 in perturbative QCD approach

We calculate the branching ratios of pure annihilation type decays B⁰→D_s^- K₂^*+ and B_s→Da₂ using the perturbative QCD approach based on k_T factorization. The branching ratios are predicted to be (60.6_{-16.5-10.4-2.1}^{+17.3+4.3+3.2} )× 10^-6 for B⁰→D_s^- K₂^*+, (1.1_-0.4-0.2-0.1^+0.4+0.1+0.1)×10^-6 for B_s→D⁰a₂⁰ and (2.3_-0.8-0.4-0.1^+0.8+0.2+0.1)×10^-6 for B_s→D^-a₂⁺. They are large enough to be measured in the ongoing experiment. Due to the shortage of contributions from penguin operators, there are no direct CP asymmetries for these decays in the Standard Model. We also derive simple relations among these decay channels to reduce theoretical uncertainties for the experiments to test the accuracy of theory and search of new physics signal.     

太阳能帆板平面度测量系统中光斑图像处理方法研究

太阳能帆板的平面度测量是卫星生产制造过程中的一个关键技术，现有的测量方法存在着精度差，效率低的问题。该文在基于实际工程课题的太阳能帆板平面度测量系统基础上，针对测量系统中光斑图像处理这一关键技术进行了详细的研究。对现有测量方法进行了比较与分析，介绍了测量系统的基本原理、图像采集系统设计过程中采取的主要措施、图像处理的具体方法与步骤和测量系统的基本组成。提出了一种新的快速滤波算法和光斑图像能量中心求取算法，大大提高了光斑图像能量中心的求取精度和实时性，提高了太阳能帆板平面度的测量精度。给出了光斑图像处理结果、静态测量重复性误差以及实际帆板的测量结果与分析，实验结果证明所采用的光斑图像处理方法可以满足对实际帆板测量精度的要求。     

Flextensional fiber Bragg grating-based accelerometer for low frequency vibration measurement

The intelligent structural health monitoring method,which uses a fiber Bragg grating(FBG) sensor,is a new approach in the field of civil engineering. However,it lacks a reliable FBG-based accelerometer for taking structural low frequency vibration measurements. In this letter,a flextensional FBG-based accelerometer is proposed and demonstrated. The experimental results indicate that the natural frequency of the developed accelerometer is 16.7 Hz,with a high sensitivity of 410.7 pm/g. In addition,it has a br...