Effect of oxygen on regulation of properties of moderately boron-doped diamond films

Regulation of oxygen on properties of moderately boron-doped diamond films is fully investigated. Results show that, with adding a small amount of oxygen (oxygen-to-carbon ratio < 5.0%), the crystal quality of diamond is improved, and a suppression effect of residual nitrogen is observed. With increasing ratio of O/C from 2.5% to 20.0%, the hole concentration is firstly increased then reduced. This change of hole concentration is also explained. Moreover, the results of Hall effect measurement with temperatures from 300 K to 825 K show that, with adding a small amount of oxygen, boron and oxygen complex structures (especially B₃O and B₄O) are formed and exhibit as shallow donor in diamond, which results in increase of donor concentration. With further increase of ratio of O/C, the inhibitory behaviors of oxygen on boron leads to decrease of acceptor concentration (the optical emission spectroscopy has shown that it is decreased with ratio of O/C more than 10.0%). This work demonstrates that oxygen-doping induced increasement of the crystalline and surface quality could be restored by the co-doping with oxygen. The technique could achieve boron-doped diamond films with both high quality and acceptable hole concentration, which is applicable to electronic level of usage.     

介观电路中量子纠缠的经典对应

从量子力学诞生日起,它的经典对应(或类比)一直是物理学家关心的话题.本文以介观电路量子化的框架中,带有互感的两个介观电容-电感(LC)电路为例,首次讨论了量子纠缠的经典类比(或对应)问题.先用有序算符内的积分理论证明其互感是产生量子纠缠的源头;再推导出求解特征频率的公式,就发现它与一个经典系统的小振动频率的表达式有相似之处,该经典系统组成如下:两个墙壁各连一个相同的弹簧,两个弹簧之间接着一个滑动小车可以在光滑的桌面上运动,小车挂有一根单摆.用分析力学求此系统的小振动频率,发现与上述介观电路的特征频率形式类似,单摆的摆动会造成小车来回振动,摆、小车和弹簧的互相牵制效应反映了小车和摆的"纠缠".     

Vacuum-gap-based lumped element Josephson parametric amplifier

We propose a lumped element Josephson parametric amplifier with vacuum-gap-based capacitor.The capacitor is made of quasi-floating aluminum pad and on-chip ground.We take a fabrication process compatible with air-bridge technology,which makes our design adaptable for future on-chip integrated quantum computing system.Further engineering the input impedance,we obtain a gain above 20 dB over 162-MHz bandwidth,along with a quasi quantum-limit noise performance.This work should facilitate the development of quantum information processing and integrated superconducting circuit design.     

Melting thermodynamics of oligonucleic acids conjugated with relatively solvophobic linear polymers: A coarse‐grained molecular simulation study

Oligonucleic acids (ONAs), such as DNA and RNA, are used in various biotechnology and nanotechnology applications due to their ability to form a double helix that is stable at low temperature and melts at high temperatures. The melting temperature (T_m) of ONA duplexes can be tuned by the ONA composition, sequence, length and concentration, solvent quality, and salt concentration and by conjugation to other macromolecules. In this article, we use coarse‐grained (CG) molecular simulations to study ONAs conjugated with linear homopolymers that are relatively more solvophobic than the ONA. We study charged and stiff 8‐mer ONAs (e.g., DNA) and neutral and flexible 8‐mer ONAs (e.g., peptide nucleic acids or PNA), and vary the composition (or G‐C content) and sequence of ONA, conjugated homopolymer lengths and solvent quality for the polymer. For neutral and flexible ONAs, as the solvent quality worsens for the polymer, the ONA melting temperature increases from that of unconjugated ONA. The melting curves broaden with polymer length and worsening solvent quality, especially for ONAs with higher G‐C content. For charged and stiff ONAs, as the solvent quality worsens, the ONA melting temperature decreases compared to unconjugated ONA while the width of the melting curve remains the same. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1196–1208     

Assessment of Noise Exposure of Sawmill Workers in Southwest,Nigeria

Economic wood processing employs the use of industrial machines for cutting, shaping, milling, and sawing timber, thereby leading to the generation of high levels of noise. Published data from empirical studies have categorized noise as an environmental hazard of global significance. Furthermore, noise exposure limits for different industries and all the industrial machines available has not been formally established as it presently exists in developed nations around the world. Therefore, this study assessed the daily exposure of sawmills workers to noise in Southwestern Nigeria. Reconnaissance surveys were first carried out in Osun, Oyo, Ondo, Ekiti, Lagos, and Ogun States to select sawmills that were fully operational and fit for the study. Two fully functional sawmills in two cities of each State were eventually selected for data collection, making a total of 24 sawmills, while the Circular Machines (CM), Planer Machines (PM), and Band-saw Machines (BM) were the machines in each sawmill considered. Two machines each of CM, PM, and BM were considered in each sawmill, making a total of forty-eight (48) machines each of CM, PM, and BM. Sound data were collected between 7 am and 7 pm each day for six days (between Monday and Saturday) using Extech 407732 sound level meter and all stabilized measurements were taken three times at different intervals. The data collected were in three different periods: Machine No-work Period (NP_m), Machine Idle Period (IP_m), and Machine Working Period (WP_m). A two–way Analysis of Variance (ANOVA) was carried out at P < 0.05 to determine whether there is a significant difference in the sound level average before and after the break, for both the idle and working periods of the three machines considered. This was also done to determine whether there is a significant difference between the sound level average of the results collected during idle and working periods of the three machines. Noise Pollution Levels (L_np) ranged from 83.20 dB (PM) to 107.65 (BM) and 93.42 (CM and PM) – 116.00 (BM) respectively, while IP_m also gave the least noise pollution level of 95.79 dB and WP_m gave the highest level of 102.88 dB. The results revealed that all the machines’ L_np values in the working period are more than the 90 dB acceptable limit the recommendation value of 90 dB while 89.6% of CMs, 75% of PMs, and 89.6% of BM had their L_np above 90 dB in the idle period respectively. The minimum and the maximum noise dose levels for IP_m, WP_m and overall are 0.09 (BM) and 2.37 (CM), 0.50 (CM), and 4.77 (PM) and 0.69 (BM) and 6.64 (PM) respectively. The study found out that the fundamental contributing factors to the high noise levels in sawmills are poor machine maintenance, use of old and obsolete machines, poor housekeeping strategy, limited space, workers’ negligence, lack of PPE, and lack of occupational safety training. The study recommends that proper workplace practices such as use of personal protective equipment, new and modern machines, training, and occupational safety programmes be implemented in the considered sawmills.     

Hyperparameter on-line learning of stochastic resonance based threshold networks

Aiming at training the feed-forward threshold neural network consisting of nondifferentiable activation functions, the approach of noise injection forms a stochastic resonance based threshold network that can be optimized by various gradient-based optimizers. The introduction of injected noise extends the noise level into the parameter space of the designed threshold network, but leads to a highly non-convex optimization landscape of the loss function. Thus, the hyperparameter on-line learning procedure with respective to network weights and noise levels becomes of challenge. It is shown that the Adam optimizer, as an adaptive variant of stochastic gradient descent, manifests its superior learning ability in training the stochastic resonance based threshold network effectively. Experimental results demonstrate the significant improvement of performance of the designed threshold network trained by the Adam optimizer for function approximation and image classification.     

In vitro anticomplementary activity and quality evaluation of dried blossoms of Inula nervosa Wall. from different geographical origins

Blossoms of Inula nervosa Wall. (BINW) are traditionally used as an analgesic and antitussive in China. In this study, in vitro anticomplementary activities of crude extract from BINW in 21 batches and of extracts of four monomeric compounds were evaluated by the classical pathway. The effect of the region of origin on the quality of BINW was evaluated by fingerprint analysis for the first time. Furthermore, chemometric methods including similarity analysis and principal component analysis were employed to evaluate the quality of BINW. The nine major monomeric compounds were quantitated by ultra‐high‐performance liquid chromatography. All nine analytes demonstrated excellent linearity with recoveries ranging from 97.25% to 102.76%. The limits of detection and quantification were 0.07–12.20 μg/mL and 0.22–40.27 μg/mL, respectively. Results indicate that different regions of origin have a significant effect on the quality of BINW. Fingerprint analysis in combination with chemometrics and multi‐ingredient determination is an efficient and reliable approach for quality evaluation. The BINW samples from Yunnan had the highest ratio of 1,5‐dicaffeoylquinic acid and thymol; they also exhibited significantly higher anticomplementary activity than those from three other areas. This study successfully established a rapid and efficient method to evaluate the quality and biological activity of BINW.     

基于计算机视觉技术的茶叶品质随机森林感官评价方法研究

为弥补茶叶品质感官审评存在的缺陷，利用计算机视觉技术对茶叶品质进行快速无损评价研究。以碧螺春绿茶为对象，依据专家感官审评结果，将茶样分成4个等级；采用中值滤波及拉普拉斯算子对茶样图像进行预处理，并提取预处理后的茶样图像的颜色特征和纹理特征以表征茶叶图像的外形特征，利用随机森林算法对茶叶外形特征属性进行重要性排序；筛选出重要性较大的特征及随机森林算法中最优的决策树棵数建立感官评价模型，并与建立的支持向量机(SVM)模型性能相比较。结果表明：色调均值、色调标准差、绿体均值、平均灰度级、饱和度均值、红体均值、饱和度标准差、亮度均值、一致性等9个特征属性的重要性较大，且与感官审评特征描述结果相一致；当采用优选出的9个重要性较大的特征及决策数棵数为500时，建立的模型性能最优，模型总体判别率为95.75%，Kappa系数为0.933，OOB误差为5%，较SVM模型分别提高了3.5%，0.066，优选的9个重要性较大的图像特征与感官审评特征描述相一致。研究表明：利用随机森林方法筛选出对茶叶外形特征属性贡献最大的少数几个特征建立模型，模型性能就能达到很好的识别效果，模型得到简化，同时模型精度和稳定性都高于其他方法。     

科研成果向教学实验的转化设计与实践成效*

围绕学校高水平应用型人才培养目标,依托省级重点实验室与省级化学化工大学生创新训练中心等科研教学平台,将“零排放型化学镀镍及其废液资源化为掺杂型LiFePO₄/C复合材料”的科研成果进行拆解和提炼,设计为分阶段、多层次的10个教学实验项目,并予以实践。结果表明,该科教融合模式营造出良好的科研氛围,有利于学生科研素养与创新意识的培养、实践能力与创新能力的提升。     

柱面微通道板的制备及其性能研究

针对未来空间天文学应用的超分辨率光谱成像仪器的需求，对低噪声柱面微通道板（MCP）的制备方法及其性能进行了研究. 提出了一种将光学抛光与热成型相结合的新的柱面MCP制备方法，利用不含放射性元素的低噪声MCP玻璃，制备出曲率半径为400mm、尺寸为30mm′46mm、长径比为80:1、通道直径12.5mm、通道间距15mm的柱面MCP，并将其与感应电荷楔条形阳极（WSA）组成光子计数探测器，对其暗计数率、分辨率进行了检测，暗计数率约为0.1counts/cm2×s.