一种通过梯形PPMgLN波导倍频实现带宽可调谐光源的理论研究

本文设计了一种梯形的周期极化掺镁铌酸锂(PPMgLN)波导,并通过在传播方向上引入温度梯度来拓宽其倍频(SHG)过程的泵浦光源可接收带宽。通过有限差分的光束传输法,计算波导的有效折射率,并进行波导尺寸的设计。结果表明,通过改变梯形波导不同位置的温度,使其形成一个温度梯度,可拓宽泵浦光源的波长可接收带宽。本文所设计的PPMgLN波导最大泵浦光源可接收带宽为C波段,即1 530~1 565 nm,该波导可倍频C波段,得到输出波段带宽为765~782.5 nm,温度调谐范围为30~150 ℃。     

Advances in rapid and effective break-in/conditioning/recovery of automotive PEMFC stacks

Automotive proton exchange membrane fuel cell stacks need to meet manufacturer specified rated beginning-of-life (BOL) performance before being assembled into vehicles and shipped off to customers. The process of “breaking-in” of a freshly assembled stack is often referred to as “conditioning.” It has become an intensely researched area especially in automotive companies, where imminent commercialization of fuel cell electric vehicles (FCEVs) demands a short, energy- and cost-efficient, and practical conditioning protocol. Significant advances in reducing the conditioning time from 1 to 2 days to as low as 4h or less, in some cases without the use of additional inert gases such as nitrogen, and with minimal use of hydrogen, and specialized test stations will be discussed.     

以磷化铁为添加剂沿(111)面生长磷掺杂金刚石大单晶

掺杂是调控金刚石性能的一种重要手段。本文采用温度梯度法,在5.6 GPa、1 312 ℃的条件下,选用Fe₃P作为磷源进行磷掺杂金刚石大单晶的合成。金刚石样品的显微光学照片表明,随着Fe₃P添加比例的增加,金刚石晶体的颜色逐渐变深,包裹体数量逐渐增加,晶形由板状转变为塔状直至骸晶。金刚石晶形的变化表明Fe₃P的添加使生长金刚石的V形区向右偏移,这是Fe₃P改变触媒特性的缘故。红外光谱分析表明,Fe₃P的添加使金刚石晶体中氮含量上升,这说明磷的进入诱使氮原子更容易进入金刚石晶格中。激光拉曼光谱测试表明,随着Fe₃P添加比例的增加,所合成的掺磷金刚石的拉曼峰位变化不大,其半峰全宽(FWHM)值变大,这说明磷的进入使得金刚石晶格畸变增加。XPS测试结果显示,随着Fe₃P添加比例的增加,金刚石晶体中磷相对碳的原子百分含量也会增加,这意味着添加Fe₃P所合成的金刚石晶体中有磷存在。     

Electrochemical sensing of H2O2 using cobalt oxide modified TiO2 nanotubes

Cobalt oxide (Co₃O₄) modified anatase titanium dioxide nanotubes (ATNTs) have been investigated for the electrochemical sensing of hydrogen peroxide (H₂O₂). ATNTs have been synthesized by a two-step anodization process. ATNTs were then modified with Co₃O₄ employing chemical bath deposition method. The structure and morphology of ATNTs and their modification with Co₃O₄ has been confirmed by X-ray diffraction by scanning electron microscopy. H₂O₂ sensing has been studied in 0.1 M PBS solution, by cyclic voltammetry and amperometry. Variation in the peak positions and current densities was observed with addition of H₂O₂ for Co₃O₄ modified ATNTs. Sensitivity and limit of detection improved with modification of ATNTs with Co₃O₄ with precursor concentration up to 0.8 M. However, at higher precursor concentrations sensitivity and limit of detection toward H₂O₂ deteriorated. Co₃O₄ Modified ATNTS using 0.8 M precursor concentration are comparatively more suitable for H₂O₂ sensing applications due to the optimum formation of Co₃O₄/ATNTs heterojunctions.     

Nonlinear elastic constitutive relations of residually stressed composites with stiff curved fibres

Applied Mathematics and Mechanics - Mechanical models of residually stressed fibre-reinforced solids, which do not resist bending, have been developed in the literature. However, in some residually...     

雾化辅助化学气相沉积法氧化镓薄膜生长研究

采用自主设计搭建的雾化辅助化学气相沉积系统设备,开展了Ga₂O₃薄膜制备及其特性研究工作。通过X射线衍射研究了沉积温度、系统沉积压差对Ga₂O₃薄膜结晶质量的影响。结果表明,Ga₂O₃在425~650 ℃温度区间存在物相转换关系。随着沉积温度从425 ℃升高至650 ℃,薄膜结晶分别由非晶态、纯α-Ga₂O₃结晶状态向α-Ga₂O₃、β-Ga₂O₃两相混合结晶状态改变。通过原子力显微镜表征探究了生长温度对Ga₂O₃薄膜表面形貌的影响,从475 ℃升高至650 ℃时,薄膜表面粗糙度由26.8 nm下降至24.8 nm。同时,高分辨X射线衍射仪测试表明475 ℃、5 Pa压差条件下的α-Ga₂O₃薄膜样品半峰全宽仅为190.8″,为高度结晶态的单晶α-Ga₂O₃薄膜材料。     

In vitro investigation of cartilage regeneration properties of polymeric ceramic hybrid composite

There would be a major effect on the cartilage regeneration characteristics of ceramic material in a substrate implant requiring biologically active biomaterials and the reinforcement phase. At this moment, we produced collagen-hyaluronic acid @ hydroxyapatite-halloysite nanotube-single walled carbon nanotube composites, which is a successful technique for making a scaffold with a superior counter for cartilage property. FTIR, XRD, and SEM-EDAX were used to perform morphological and structural studies. The prepared composite's surface feature was investigated and discovered by HRTEM-SAED analysis, and it observed porous nature. The simulated body fluids (SBF) assessment of the materials was noticed their bioactivity and chondrocytes to determine their biocompatibility. Hybrid composite displayed promise for cartilage tissue engineering despite mesenchymal stem cells compatibility effect and magnificently demonstrated an antibacterial effect without antibiotics. The live/dead cells analysis shows that the composite can significantly improve mesenchymal stem cells, and the composite has the potential ability for cartilage regeneration. The above characteristics make the material quite interesting and important in the area for regenerative medicinal uses.     

直接碳燃料电池燃料的研究进展

直接碳燃料电池(DCFC)是一种清洁高效利用碳资源发电的装置。其因能量转换率高,对环境污染小,燃料选择范围广等优点获得了越来越多的关注。DCFC的性能与使用的燃料密切相关,为了探究燃料对DCFC的影响,本文分别阐述了石墨、炭黑、中密度纤维板、生物质、煤、活性炭的特性及改性方法,分析讨论了燃料表面含氧官能团以及燃料中的金属催化剂对阳极电化学反应的促进作用,发现燃料表面化学性质要比比表面积更加重要。同时,本文也提出了对生物质这一优良的可再生资源的期待,为未来DCFC燃料的发展提供参考。     

Analysis on First-stage Ignition of n-Heptane at Low Temperatures with a Lumped Skeletal Mechanism

Two-stage ignition exists in the low-temperature combustion process of n-heptane and the first-stage ignition also shows a negative temperature coefficient(NTC) phenomenon. To study key reactions and understand chemical principles affecting the first-stage ignition of n-heptane, a lumped skeletal mechanism with 62 species is obtained based on the detailed NUIGMech1.0 mechanism using the directed relation graph method assisted by sensitivity analysis and isomer lumping. The lumped mechanism shows good performance on ignition delay time under wide conditions. The study revealed that the temperature after the first-stage ignition is higher and a larger amount of fuel is consumed at lower initial temperatures. The temperature at the first-stage ignition is relatively insensitive to the initial temperature. Further sensitivity analysis and reaction path analysis carried out based on the lumped mechanism show that the decomposition of RO₂ to produce alkene and HO₂is the most important reaction to inhibit the first-stage ignitions. The chain branching explosion closely related to the first-stage ignition will be terminated when the rate constant for the RO₂ decomposition is larger than that of the isomerization of RO₂ to produce QOOH. The NTC behavior as well as other characteristics of the first-stage ignition can be rationalized from the competition between these two reactions.     

金刚石衬底上GaN HEMT沟道温度建模:各向异性且非均匀热导率的影响

为了改善GaN HEMT的自热效应,集成高热导率的金刚石衬底有助于增强器件有源区的热量耗散。然而,化学气相淀积(CVD)生长的多晶金刚石(PCD)具有柱状晶粒结构,导致了各向异性的材料热导率,且其热导率值与生长厚度有关。为此,通过建模金刚石生长过程中晶粒尺寸的演变过程,计算了金刚石沿面内和截面方向的热导率。基于该PCD热导率模型,利用计入材料非线性热导率的GaN器件热阻解析模型,计算得到了GaN HEMT沟道温度的波动范围,并分析了其与器件结构(栅长、栅宽、栅间距、衬底厚度)和功耗的依赖关系。最后,通过与有限元(FEM)仿真结果对比,分区域提取了GaN HEMT器件中PCD衬底的有效热导率,分别为260~310 W/(m·K)和1 250~1 450 W/(m·K)。本文的计算为预测金刚石衬底上GaN HEMT器件的沟道温度提供了快速、有效的方法。