Computational-Based Approach for Predicting Porosity of Electrospun Nanofiber Mats Using Response Surface Methodology and Artificial Neural Network Methods

Comparative studies between response surface methodology (RSM) and artificial neural network (ANN) methods to find the effects of electrospinning parameters on the porosity of nanofiber mats is described. The four important electrospinning parameters studied included solution concentration (wt.%), applied voltage (kV), spinning distance (cm) and volume flow rate (mL/h). It was found that the applied voltage and solution concentration are the two critical parameters affecting the porosity of the nanofiber mats. The two approaches were compared for their modeling and optimization capabilities with the modeling capability of RSM showing superiority over ANN, having comparatively lower values of errors. The mean relative error for the RSM and ANN models were 1.97% and 2.62% and the root mean square errors (RMSE) were 1.50 and 1.95, respectively. The superiority of the RSM-based approach is due to its high prediction accuracy and the ability to compute the combined effects of the electrospinning factors on the porosity of the nanofiber mats.     

Formation of porous polymer morphology by microsyneresis during divinylbenzene polymerization

This article describes the investigation of the importance of various reaction conditions on microsyneretic pore formation during polymerization of divinylbenzene (DVB) under so‐called “solvothermal” conditions. To induce microsyneretic pore formation, the most important parameter is an unusually high dilution of monomers with a “good” porogen solvating the polymer chains. High dilution and solvation of the growing poly(DVB) chains promote the prolongation of the polymer chains rather than their interconnection by crosslinking. Consequently, when the polymer gel density reaches the point where syneresis starts, the polymer network is geometrically too extensive to be broken up into precipitating entities and, instead, porogen droplets are formed within the continuous polymer gel. The pore geometry created by microsyneresis offers high surface area in wide mesopores and hence, high capacity for supporting functional groups or reactions with much better accessibility than narrow pores between polymer microspheres produced by macrosyneresis in conventional styrenic polymer supports. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 774–781     

粘弹性地基上含孔隙的石墨烯增强功能梯度板的振动

为分析粘弹性地基上含孔隙的石墨烯增强功能梯度板的自由和强迫振动特性，基于三参数粘弹性地基模型及复合材料薄板理论，建立了粘弹性地基上含孔隙石墨烯增强功能梯度板的运动方程，用伽辽金法求解其固有频率和动力响应，并通过数值算例分析了粘弹性地基参数、孔隙率、孔隙类型及石墨烯纳米片分布模式、含量等因素对自由振动和动力响应的影响．结果表明，固有频率随着孔隙率的增大非单调变化，孔隙率对固有频率的影响随着地基参数、孔隙类型的不同而不同．另外，在三种孔隙类型中，上下表面层含有最少孔隙数量的板的动挠度最小，且其动挠度随着孔隙率的增大而微弱提高．     

Microporosity of a Guanidinium Organodisulfonate Hydrogen‐Bonded Framework

Guanidinium organosulfonates (GSs) are a large and well‐explored archetypal family of hydrogen‐bonded organic host frameworks that have, over the past 25 years, been regarded as nonporous. Reported here is the only example to date of a conventionally microporous GS host phase, namely guanidinium 1,4‐benzenedisulfonate ( p ‐G₂BDS ). p ‐G₂BDS is obtained from its acetone solvate, AcMe@ G₂BDS , by single‐crystal‐to‐single‐crystal (SC‐SC) desolvation, and exhibits a Type I low‐temperature/pressure N₂ sorption isotherm (SA_BET=408.7(2) m² g^?1, 77 K). SC‐SC sorption of N₂, CO₂, Xe, and AcMe by p ‐G₂BDS is explored under various conditions and X‐ray diffraction provides a measurement of the high‐pressure, room temperature Xe and CO₂ sorption isotherms. Though p ‐G₂BDS is formally metastable relative to the “collapsed”, nonporous polymorph, np ‐G₂BDS , a sample of p ‐G₂BDS survived for almost two decades under ambient conditions. np ‐G₂BDS reverts to zCO₂@ p ‐G₂BDS or yXe@ p ‐G₂BDS (y,z=variable) when pressure of CO₂ or Xe, respectively, is applied.     

CO2-水-页岩相互作用的研究现状及展望

简要综述了CO2、水和页岩间矿物的相互作用,分析了CO2注入到地下进入页岩层后,地下含水层pH值的变化,并根据页岩层的矿物学组成分为黏土矿物和脆性矿物,较为详细地描述了CO2与黏土矿物和脆性矿物之间发生的地球化学反应,概述了此反应对页岩层孔隙度和渗透率的影响。同时,也讨论了CO2增强页岩气开采的现实问题及发展趋势,为今后的研究提供了参考。     

EFFECT OF DAMAGE EVOLUTION ON POISSON’S RATIO OF CONCRETE UNDER SULFATE ATTACK

Experimental results about concrete under sulfate attack are summarized,which include the variation of mass density of samples and velocity of ultrasonic wave propagating in samples.The evolution damage is analyzed in terms of the experimental results,and close attention is paid to the effect of damage evolution on Poisson’s ratio.This study shows that Poisson’s ratio is significantly affected by the concentration of solution and water-cement ratio.Poisson’s ratio of concrete changes very little when the water-cement ratio is selected as 0.6 or 0.8,so that such change may be neglected.If water-cement is 0.4,however,the Poisson’s ratio of the sample significantly changes.When the concrete sample of 0.4 water-cement ratio is immersed in sodium sulfate solution of 8% concentration for 285 days,Poisson’s ratio increase 10.14% compared with its initial value.There exist a sensitive region and a non-sensitive region for the change rate of Poisson’s ratio with respect to corrosion time.The change rate of Poisson’s ratio monotonously decreases with corrosion time in the sensitive region;in the non-sensitive region,the change rate of Poisson’s ratio is almost equal to zero.     

低孔隙度疏松铝的高压声速与冲击熔化

对含微孔洞疏松度m=1.04的疏松铝进行了冲击加载-卸载实验,利用DISAR(distance interferometer system for any reflector)测得了53至99 GPa五个冲击压力下疏松铝/LiF界面粒子速度波剖面,获得了各压力下的纵波声速和其中三个压力点的体波声速,确定出疏松铝的冲击熔化压力约为81 GPa,确定出高压下冲击熔化前的泊松比约为0.372.通过分析,微孔洞明显降低了冲击熔化压力,引起的非谐振效应明显,状态方程计算中考虑非谐效应,非谐因子l 关键词： 低孔隙度 疏松铝 声速 冲击熔化     

透明激光陶瓷散射损耗分析

 为了定量分析激光陶瓷中散射损耗对其透过率的影响,通过建立气孔尺寸分布模型,引入第二相体积比概念,并结合Mie散射、瑞利散射和全散射积分等理论,讨论了激光陶瓷中气孔、晶界第二相和表面粗糙度等引起的散射损耗对激光陶瓷透光性能的影响。研究结果表明：气孔率的大小将明显影响陶瓷透过率,且气孔尺寸分布决定了透过率包络的变化趋势;晶界和表面散射对透过率的影响主要集中在短波长处;在气孔率较低情况下,晶界第二相的存在是导致短波长处透过率急剧降低的主要因素。     

透明陶瓷透光性能的影响因素

 研究了影响激光透明陶瓷透光性能的主要因素,讨论了陶瓷内部气孔和杂质颗粒等散射粒子、晶界结构中晶界折射率与晶粒折射率的差异以及晶界表面粗糙度等因素对陶瓷透光性能的影响,并定量分析了激光陶瓷透过率随气孔尺寸、气孔率、晶粒相对晶界折射率以及晶界表面粗糙度的变化关系。结果表明： 陶瓷的透过率随着气孔率的减小而增大,但透过率随气孔尺寸的增大而呈现出周期性振荡,且当气孔尺寸与入射光波长可比拟时,陶瓷的透过率会明显降低;在晶界结构中,晶界的折射率与晶粒的折射率相差越小,陶瓷的透过率就越高;晶界表面粗糙度越大,透过率越低。然而,晶界折射率不同于晶粒折射率,这使得其陶瓷透过率降低的程度比对晶界表面粗糙度的影响明显得多。在陶瓷制备过程中,需要重点排除尺寸与入射波长可比拟的气孔, 以抑制晶界结构中第二相的产生。     

烧结金属纤维板大空间自然对流实验研究

实验研究了烧结金属纤维板在大空间下的自然对流换热,分析了倾角、孔隙率、纤维丝经、Ra数和金属纤维导热系数对换热性能的影响.实验结果表明:存在最优的角度(60°左右)使烧结金属纤维板的自然对流换热性能最好,但倾斜角度对烧结金属纤维板的换热影响没有光板显著;加热面的平均Nu数随着纤维直径和孔隙率的增加均先增加后减小;在实验...