弹性地基上含孔隙功能梯度材料板的自由振动和动力响应

为研究弹性地基上含孔隙的材料特性沿厚度呈Sigmoid函数变化的功能梯度材料(S-FGM)板的振动特性,本文基于改进的Voigt模型,分别建立了孔隙为均匀分布和非均匀分布两种类型的功能梯度材料的物性参数模型。根据复合材料薄板理论导出了弹性地基上含孔隙的功能梯度材料板的运动方程,用伽辽金法寻求四边简支边界条件下板自由振动和动力响应的解析解;讨论了孔隙、弹性地基参数、材料组分指数等因素对S-FGM板自由振动和动力响应的影响。结果表明:孔隙对板自振频率的影响比较复杂,不仅与孔隙率的大小和分布形式有关,还与弹性地基参数有关;当有弹性地基作用时,板的量纲归一化基频随着孔隙率的增大而提高,并且孔隙均匀分布的S-FGM板与孔隙非均匀分布的情况相比,其量纲归一化基频更高;孔隙增大了板的动力响应,其中孔隙为均匀分布的板的动力响应对孔隙率的变化更为敏感。     

弹性地基中含孔隙的功能梯度圆锥壳的振动分析

为研究弹性地基中多孔功能梯度材料圆锥壳的振动特性,基于经典薄壳理论建立了弹性地基中含均匀和非均匀分布孔隙的功能梯度材料圆锥薄壳的振动方程,并用伽辽金法求得了自由振动和动力响应的解。通过参数分析讨论了孔隙、弹性地基参数、半锥角等因素对功能梯度圆锥壳自由振动和动力响应的影响。结果表明,弹性地基的压缩和剪切刚度的增大提高了圆锥壳的振动频率而显著减小了动力响应;当半锥角增大时,圆锥壳的动力响应显著增大。与非均匀分布孔隙壳体相比,均匀分布孔隙壳体的自振频率和动力响应随孔隙率的变化更为敏感。     

三参数粘弹性地基上层合板的自由和强迫振动

基于三参数粘弹性地基模型及Reddy高阶剪切变形板理论,用双重Fourier级数形式解求得粘弹性地基上四边简支对称正交及反对称斜交层合板的各模态自由振动频率的解析解,以及这两种层合板在任意横向动荷载作用下动力响应的半解析解。通过参数分析讨论了粘弹性地基参数、边厚比等因素对自振频率及动力响应的影响。结果表明,地基的剪切刚度和压缩刚度提高了板的自振频率而降低了板的振动幅值,地基的粘性作用不可忽略。     

黏弹性地基上功能梯度材料板的振动分析

为研究黏弹性地基上功能梯度材料板的自由和强迫振动特性,基于Reddy高阶剪切变形理论以及由Shen导得的广义Karman型方程,用双重Fourier级数法推导了三参数黏弹性地基上四边简支功能梯度材料板自由振动和动力响应的解析解,计算了各模态自振频率和半波冲击载荷作用下的动力响应,讨论了材料组分指数、黏弹性地基参数、边厚比等因素对自由振动和动力响应的影响.结果表明,黏弹性地基的剪切和压缩刚度显著提升了功能梯度材料板的振动频率,减小了动力响应;另外,地基的黏性对振动频率和动力响应也有一定的影响.     

弹性地基上多孔功能梯度材料矩形板的自由振动与临界屈曲载荷分析

多孔功能梯度材料(FGM)构件的特性与孔隙率和孔隙分布形式有密切关系。本文基于经典板理论,考虑不同孔隙分布形式时修正的混合率模型,研究Winkler弹性地基上四边受压多孔FGM矩形板的自由振动与临界屈曲载荷特性。首先利用Hamilton原理和物理中面的定义推导Winkler弹性地基上四边受压多孔FGM矩形板自由振动的控制微分方程并进行无量纲化,然后应用微分变换法(DTM)对无量纲控制微分方程和边界条件进行变换,得到计算无量纲固有频率和临界屈曲载荷的代数特征方程。将问题退化为孔隙率为零时的FGM矩形板并与已有文献进行对比以验证其有效性。最后计算并分析了梯度指数、孔隙率、地基刚度系数、长宽比、四边受压载荷及边界条件对多孔FGM矩形板无量纲固有频率的影响以及各参数对无量纲临界屈曲载荷的影响。     

热环境中旋转运动功能梯度圆板的强非线性固有振动

研究热环境中旋转运动功能梯度圆板的非线性固有振动问题．针对金属－陶瓷功能梯度圆板，考虑几何非线性、材料物理属性参数随温度变化以及材料组分沿厚度方向按幂律分布的情况，应用哈密顿原理推得热环境中旋转运动功能梯度圆板的非线性振动微分方程．考虑周边夹支边界条件，利用伽辽金法得到了横向非线性固有振动方程，并确定了静载荷引起的静挠度．用改进的多尺度法求解强非线性方程，得出非线性固有频率表达式．通过算例，分析了旋转运动功能梯度圆板固有频率随转速、温度等参量的变化情况．结果表明，非线性固有频率随金属含量的增加而降低；随转速和圆板厚度的增大而升高；随功能梯度圆板表面温度的升高而降低．     

功能梯度旋转圆板的热弹性固有振动

在考虑热因素及旋转运动条件下，针对金属－陶瓷功能梯度圆板的固有振动问题进行研究．给出随温度变化且材料组分沿厚度方向按幂律分布的材料物性参数，依据热弹性理论得到圆板的能量关系式．基于哈密顿原理建立旋转金属－陶瓷功能梯度圆板热弹性动力学方程．采用伽辽金法得到边界约束下圆板的自由振动方程，确定了静挠度及固有振动频率．基于数值计算，得到系统固有频率值随体积分数指数、转速和温度等参量的变化曲线，讨论了静挠度变化规律及动力系统的奇点稳定性问题．结果表明，固有频率随体积分数指数、材料表面温度以及转速的增加而减小．     

热环境中旋转运动功能梯度圆板的强非线性固有振动

研究热环境中旋转运动功能梯度圆板的非线性固有振动问题．针对金属－陶瓷功能梯度圆板,考虑几何非线性、材料物理属性参数随温度变化以及材料组分沿厚度方向按幂律分布的情况,应用哈密顿原理推得热环境中旋转运动功能梯度圆板的非线性振动微分方程．考虑周边夹支边界条件,利用伽辽金法得到了横向非线性固有振动方程,并确定了静载荷引起的静挠度．用改进的多尺度法求解强非线性方程,得出非线性固有频率表达式．通过算例,分析了旋转运动功能梯度圆板固有频率随转速、温度等参量的变化情况．结果表明,非线性固有频率随金属含量的增加而降低;随转速和圆板厚度的增大而升高;随功能梯度圆板表面温度的升高而降低．     

多孔功能梯度材料Timoshenko梁的自由振动分析

基于Timoshenko梁理论研究多孔功能梯度材料梁(FGMs)的自由振动问题.首先,考虑多孔功能梯度材料梁的孔隙率模型,建立了两种类型的孔隙分布.其次,基于Timoshenko梁变形理论,给出位移场方程、几何方程和本构方程,利用Hamilton原理推导多孔功能梯度材料梁的自由振动控制微分方程,并进行无量纲化,然后应用微分变换法(DTM)对无量纲控制微分方程及其边界条件进行变换,得到含有固有频率的等价代数特征方程.最后,计算了固定-固定(C-C)、固定-简支(C-S)和简支-简支(S-S)三种不同边界下多孔功能梯度材料梁自由振动的无量纲固有频率.将其退化为均匀材料与已有文献数据结果对照,验证了正确性.讨论了孔隙率、细长比和梯度指数对多孔功能梯度材料梁无量纲固有频率的影响.     

弹性地基上转动FGM梁自由振动的DTM分析

基于Euler-Bernoulli梁理论,利用广义Hamilton原理推导得到弹性地基上转动功能梯度材料(FGM)梁横向自由振动的运动控制微分方程并进行无量纲化,采用微分变换法(DTM)对无量纲控制微分方程及其边界条件进行变换,计算了弹性地基上转动FGM梁在夹紧-夹紧、夹紧-简支和夹紧-自由三种边界条件下横向自由振动的无量纲固有频率,再将控制微分方程退化到无转动和地基时的FGM梁,计算其不同梯度指数时第一阶无量纲固有频率值,并和已有文献的FEM和Lagrange乘子法计算结果进行比较,数值完全吻合。计算结果表明,三种边界条件下FGM梁的无量纲固有频率随无量纲转速和无量纲弹性地基模量的增大而增大;在一定无量纲转速和无量纲弹性地基模量下,FGM梁的无量纲固有频率随着FGM梯度指数的增大而减小;但在夹紧-简支和夹紧-自由边界条件下,一阶无量纲固有频率几乎不变。     

Nonlinear dynamic analysis of moving bilayer plates resting on elastic foundations

The aim of this study is to investigate the dynamic response of axially moving two-layer laminated plates on the Winkler and Pasternak foundations. The upper and lower layers are formed from a bidirectional functionally graded(FG) layer and a graphene platelet(GPL) reinforced porous layer, respectively. Henceforth, the combined layers will be referred to as a two-dimensional(2D) FG/GPL plate. Two types of porosity and three graphene dispersion patterns, each of which is distributed through the plate thickness,are investigated. The mechanical properties of the closed-cell layers are used to define the variation of Poisson's ratio and the relationship between the porosity coefficients and the mass density. For the GPL reinforced layer, the effective Young's modulus is derived with the Halpin-Tsai micro-system model, and the rule of mixtures is used to calculate the effective mass density and Poisson's ratio. The material of the upper 2D-FG layer is graded in two directions, and its effective mechanical properties are also derived with the rule of mixtures. The dynamic governing equations are derived with a first-order shear deformation theory(FSDT) and the von Kármán nonlinear theory. A combination of the dynamic relaxation(DR) and Newmark's direct integration methods is used to solve the governing equations in both time and space. A parametric study is carried out to explore the effects of the porosity coefficients, porosity and GPL distributions, material gradients, damping ratios, boundary conditions, and elastic foundation stiffnesses on the plate response. It is shown that both the distributions of the porosity and graphene nanofillers significantly affect the dynamic behaviors of the plates. It is also shown that the reduction in the dynamic deflection of the bilayer composite plates is maximized when the porosity and GPL distributions are symmetric.     

Three-dimensional free vibration analysis of functionally graded piezoelectric annular plates on elastic foundations

Three-dimensional free vibration analysis of functionally graded piezoelectric (FGPM) annular plates resting on Pasternak foundations with different boundary conditions is presented. The material properties are assumed to have an exponent-law variation along the thickness. A semi-analytical approach which makes use of state-space method in thickness direction and one-dimensional differential quadrature method in radial direction is utilized to obtain the influences of the Winkler and shearing layer elastic coefficients of the foundations on the non-dimensional natural frequencies of functionally graded piezoelectric annular plates. The analytical solution in the thickness direction can be acquired using the state-space method and approximate solution in the radial direction can be obtained using the one-dimensional differential quadrature method. Numerical results are given to demonstrate the convergency and accuracy of the present method. The influences of the material property graded index, circumferential wave number and thickness of the annular plate on the dynamic behavior are also investigated. Since three-dimensional free vibration analysis of FGPM annular plates on elastic foundations has not been implemented before, the new results can be used as benchmark solutions for future researches.     

功能梯度石墨烯增强复合材料板的自由振动

基于高阶函数剪切变形板理论,研究了可移动简支边界条件下功能梯度石墨烯增强复合材料板的自由振动。利用修正的Halpin-Tsai模型估计了复合材料的等效杨氏模量。基于Hamilton原理构建其偏微分方程。通过Navier方法计算得到了板的量纲为一的频率,并与已有成果进行了比较,验证了本文计算模型的优越性。数值计算结果表明:功能梯度石墨烯增强复合材料板的量纲为一的基频受石墨烯小块的分布模式影响很大,随着石墨烯含量的增加而单调增加;固定石墨烯小块的厚度和长宽比,量纲为一的基频随着长厚比的增加而单调增加。     

Three-dimensional free vibration analysis of four-parameter continuous grading fiber reinforced cylindrical panels resting on Pasternak foundations

This research investigates three-dimensional free vibration analysis of four-parameter continuous grading fiber reinforced (CGFR) cylindrical panels resting on Pasternak foundations by using generalized power-law distribution. The functionally graded orthotropic panel is simply supported at the edges, and it is assumed to have an arbitrary variation of matrix volume fraction in the radial direction. A four-parameter power-law distribution presented in literature is proposed. Symmetric and asymmetric volume fraction profiles are presented. Suitable displacement functions that identically satisfy the boundary conditions at the simply supported edges are used to reduce the equilibrium equations to a set of coupled ordinary differential equations with variable coefficients, which are solved by generalized differential quadrature method, and natural frequency is obtained. The fast rate of convergence of the method is demonstrated, and to validate the results, comparisons are made with the available solutions for functionally graded isotropic shells with/without elastic foundations. The effect of the elastic foundation stiffness parameters and various geometrical parameters on the vibration behavior of the CGFR cylindrical panels is investigated. This work mainly contributes to illustrate the influence of the four parameters of power-law distributions on the vibration behavior of functionally graded orthotropic cylindrical panels resting on elastic foundation. This paper is also supposed to present useful results for continuous grading of matrix volume fraction in the thickness direction of a cylindrical panel on elastic foundation and comparison with similar discrete laminated composite cylindrical panel.     

Chebyshev collocation approach for vibration analysis of functionally graded porous beams based on third-order shear deformation theory

In this paper, vibration analysis of functionally graded porous beams is carried out using the third-order shear deformation theory. The beams have uniform and non-uniform porosity distributions across their thickness and both ends are supported by rotational and translational springs. The material properties of the beams such as elastic moduli and mass density can be related to the porosity and mass coefficient utilizing the typical mechanical features of open-cell metal foams. The Chebyshev collocation method is applied to solve the governing equations derived from Hamilton’s principle, which is used in order to obtain the accurate natural frequencies for the vibration problem of beams with various general and elastic boundary conditions. Based on the numerical experiments, it is revealed that the natural frequencies of the beams with asymmetric and non-uniform porosity distributions are higher than those of other beams with uniform and symmetric porosity distributions.     

Semi-analytical buckling analysis of heterogeneous variable thickness viscoelastic circular plates on elastic foundations

Buckling analysis of the functionally graded viscoelastic circular plates has not been carried out so far. In the present paper, a series solution is developed for buckling analysis of radially graded FG viscoelastic circular plates with variable thickness resting on two-parameter elastic foundations, based on Mindlin's plate theory. The complex modulus approach in combination with the elastic–viscoelastic correspondence principle is employed to obtain the solution for various edge conditions. A comprehensive sensitivity analysis is carried out to evaluate effects of various parameters on the buckling load. Results reveal that the viscoelastic behavior of the materials may postpone the buckling occurrence and the stiffness reduction due to the section variations may be compensated by the graded material properties.