排序方式: 共有170条查询结果,搜索用时 15 毫秒
111.
The liquid crystal (LC) panel of a commercially-available LCD projector is successfully used for beam shaping, and a Gaussian beam is converted to a square super-Gaussian beam using the configuration of amplitude modulation. The additional phase modulations imposed by the LC modulator on the shaped beams are measured precisely using an interferometric technique. The experimental results have demonstrated that such a commerciallyavailable programmable spatial light modulator is applicable to beam shaping with negligible additional phase modulation. 相似文献
112.
113.
114.
115.
针对高功率固体激光驱动器的安全运行,提出了覆盖驱动器建设全过程的污染控制方法,详细介绍了洁净清洗、洁净检测、洁净保护等保障污染控制效果的技术手段,并介绍了神光-Ⅲ主机装置片状放大器洁净度提升所采取的技术途径,以及片状放大器光照清洗实验中气溶胶等级随闪光灯照射次数的变化情况。实验结果表明,神光-Ⅲ主机装置的洁净水平与美国国家点火装置(NIF)接近且优于其他同类装置,洁净度的大幅提升为装置的安全运行提供了有力保障。 相似文献
116.
研究了CO2激光局域辐照对熔石英损伤特性的影响, 发现当辐照中心温度较低时(1139 K), 辐照对损伤阈值没有明显影响, 但辐照中心温度较高时(1638 K), 辐照对损伤阈值有明显的影响, 损伤阈值随距离辐照中心间距的增大而减小, 在残余应力产生光程差最大处附近, 损伤阈值降到最小, 随着与辐照中心间距的进一步增加, 损伤阈值略有上升. 对导致此现象的原因做了分析. 由于残余应力的存在, 在辐照中心发生再损伤产生的裂纹后, 裂纹先沿径向扩展, 在残余应力产生光程差最大处附近, 裂纹转而向切向扩展, 这可能与径向和环向张应力随半径的变化有关. 在采用热处理炉退火消除残余应力时, 必须注意元件的洁净处理, 否则退火会出现析晶现象, 对损伤阈值和透射率造成不良影响.
关键词:
2激光局域辐照')" href="#">CO2激光局域辐照
熔石英
损伤特性 相似文献
117.
118.
Calculation of the Spatio-Temporal Dynamics of Q-switched Yb^3+:YAG Laser with an Unstable Cavity and a Super-Gaussian Mirror 下载免费PDF全文
A numerical simulation used to compute the spatio-temporal dynamics of pulse formation of diode-pumped Q- switched Yb: YA G laser is carried out. The model takes the laser amplification and gain saturation, the properties of the laser cavity, and the diffractive effects of the laser disc into account. The numerical calculation is performed for a confocal positive-branch unstable resonator with a super Gaussian coupling mirror. The simulation results show that the laser pulse starts from a Gaussian intensity distribution and becomes rapidly non-Gaussian. The corresponding beam quality M^2 factor is seen to vary approximately from 1.5 at the beginning of the formation of pulse to more than 10 in the tail of the pulse, with a value of 11.6 at the peak of the pulse. 相似文献
119.
分别以丙醇锆和正硅酸乙酯为原料,采用溶胶-凝胶工艺制备了性能稳定的ZrO2和SiO2溶胶。用旋转镀膜法在K9玻璃上分别制备了单层SiO2薄膜、单层ZrO2薄膜、ZrO2/ SiO2双层膜和SiO2/ZrO2双层膜。采用原子力显微镜观察了薄膜的表面形貌,用椭偏仪测量薄膜的厚度与折射率,用紫外-可见光分光光度计测量了薄膜的透射率。对薄膜的透射光谱和椭偏仪模拟的数据进行分析,发现SiO2/ZrO2双层膜之间的渗透十分明显,而ZrO2/SiO2双层膜之间几乎不发生渗透。利用TFCalc模系设计软件,采用三层膜模型对薄膜的透射率进行模拟,得出的透射曲线与用紫外-可见光分光光度计测量的透射曲线十分符合。 相似文献
120.
用原子力显微镜和光学显微镜观测酸蚀后熔石英亚表面划痕,并根据形貌特征将其分为Boussinesq-point-force crack(BPFC)、Hertzian-conical scratch(HCS)和Plastic indent(PI)三类,测试了各类划痕的损伤阈值,讨论了激光损伤机制。结果表明锐度较大的BPFC损伤阈值不超过2.0 J/cm<>2;深度小于1 μm的 HCS阈值可达2.6 J/cm2;形变较大的PI阈值至2.8 J/cm2,形变较小的PI的激光损伤阈值与无缺陷材料相当。BPFC 和深度超过1 μm的HCS是导致熔石英损伤阈值低的主要因素。 相似文献