排序方式: 共有28条查询结果,搜索用时 15 毫秒
2.
3.
4.
5.
从(3+1)维非线性薛定谔方程出发,理论上分析了超短脉冲频谱展宽与自聚焦的影响因素。分析得出:通过改变泵浦光的功率和光束口径,可以实现光谱的极大展宽并避免自聚焦成丝。数值模拟了小口径强泵浦光束在BK7玻璃中的传输过程并进行了实验验证。模拟结果显示在超连续谱产生的同时小尺度调制被完全抑制。实验结果表明:降低泵浦光功率,使光束不会因为全光束自聚焦而发生塌陷,同时还能控制除自聚焦外的其它非线性效应,进而改善近场光束质量。由于自相位调制是超短超强脉冲产生超连续谱的重要机制之一,需要维持传输过程中的泵浦光功率,由此最佳的入射光功率应选在全光束自聚焦功率阈值附近。 相似文献
6.
7.
W/Cu梯度功能材料的高热负荷性能研究 总被引:4,自引:0,他引:4
用等离子体喷涂和热压方法制作了W/Cu梯度功能材料(FGM)样品,用大功率ND∶YAG激光对其进行了高热负载模拟实验.结果表明,在100~400MW@m-2的瞬时(脉冲宽度为4ms)热负载下,经过200~700次热循环,未发现有W-Cu复合体开裂.在123MW@m-2的功率密度下作用700次,发现钨表面有再结晶现象及严重的晶界腐蚀和裂纹,再结晶的平均晶粒尺寸约为5~10μm,垂直于表面呈柱状结构,再结晶层厚度约20~30μm.由于激光的淬冷效应,晶粒生长的趋势并不明显.在398MW@m-2功率密度下出现了明显的腐蚀坑,坑内呈疏松的蜂窝结构,坑的边缘出现了明显沉积区,能谱分析表明沉积区集聚了大量的金属杂质.等离子体喷涂试样比热压试样更易产生晶界的断裂的裂纹.在相同的热负荷条件下,W/Cu FGM的重量损失低于石墨材料的重量损失. 相似文献
8.
9.
提出了一种基于时分复用技术的全光纤、全固化的用于惯性约束聚变驱动器的甚多路光脉冲产生系统.系统中采用单纵模振荡器输出连续激光信号,利用时分复用技术结合高速电光调制技术实现序列脉冲的产生和甚多束脉冲的独立整形.采用偏振无关的声光调制技术实现甚多束脉冲的独立输出.每个序列脉冲包含8个子脉冲,子脉冲间隔设置为120ns,对子脉冲独立整形和选单后将其传输放大至微焦耳量级输出.实验成功验证了采用时分复用技术完全可以实现序列脉冲输出,各子脉冲可以独立任意整形且最后的单束输出能量为1.275μJ. 相似文献
10.
The conversion of the frequency modulated pulse induced from frequency modulation (FM) to amplitude modulation (AM) by the polarization mode dispersion (PMD) is theoretically and experimentally investigated. When there is no polarizer at the output end of a fiber system, the amplitude modulation depth is stable by 8%. Random amplitude modulation is observed when a polarizer is placed at the output end of the fiber system. The observed minimum and maximum modulation depths in our experiment are 5% and 80%, respectively. Simulation results show that the amplitude modulation is stable by 4% induced mainly by group velocity dispersion (GVD) when there is no polarizer, and the amplitude modulation depth displays the random variation character induced by the GVD and PMD. Lastly, a new fiber system scheme is proposed and little amplitude modulation is observed at the top of the output pulse. 相似文献