电子束蒸发在不同Ar气氛下外退火制备MgB2超导薄膜

制备高质量的MgB2薄膜是实现MgB2超导电子器件应用的前提和基础.我们用电子束蒸发B膜和Mg/B多层膜为前驱然后后退火的方法,分别在高温区(~900℃)和中温区(~750℃)成功获得了MgB2超导薄膜.改变退火的Ar气压条件,采用B膜前驱退火的样品Tc可达到38K以上,转变宽度0.3K.Mg/B多层膜的结果尽管Tc稍低(Tc~35K),但薄膜表面更加均匀,且避免了高温下Mg蒸汽污染的问题.对于两种前驱退火中观察到的完全不同的退火气压影响,我们认为是与其各自的超导成相过程相联系的,在此基础上我们对退火气压效应给出了自己的分析和解释,为今后进一步细致研究退火过程中的薄膜生长机制提供了参考.     

Effect of post-metallization annealing on the ferroelectric properties of sol-gel derived PZT thin films

A series of monolithic Pt-PZT-Pt capacitors was prepared based on sol-gel derived PZT 53/47 films fired to 700 C. After deposition of top Pt electrodes, the capacitors were subjected to post-metallization annealing (PMA) temperatures of 100 C to 700 C. Dielectric and ferroelectric (FE) characterizations were performed. Increasing the PMA temperature produced lower values of spontaneous and remanent polarizations, dielectric constant and leakage currents. The observations are correlated with a proposed FE capacitor model.     

Temperature dependence of excitonic luminescence from nanocrystalline ZnO films

The properties of the excitonic luminescence for nanocrystalline ZnO thin films are investigated by using the dependence of excitonic photoluminescence (PL) spectra on temperature. The ZnO thin films are prepared by thermal oxidation of ZnS films prepared by low-pressure metalorganic chemical vapor deposition (LP-MOCVD) technique. The X-ray diffraction (XRD) indicates that ZnO thin films have a polycrystalline hexagonal wurtzite structure with a preferred (0 0 2) orientation. A strong ultraviolet (UV) emission peak at 3.26 eV is observed, while the deep-level emission band is barely observable at room temperature. The strength of the exciton-longitudinal-optical (LO) phonon coupling is deduced from the temperature dependence of the full-width at half-maximum (FWHM) of the fundamental excitonic peak, decrease in exciton-longitudinal-optical (LO) phonon coupling strength is due to the quantum confinement effect.     

溅射功率对多层膜质量的影响

用磁控溅射技术制备薄膜，用X射线衍射研究在基片和靶间距离固定的情况下不同的溅射功率对薄膜结构的影响。结果表明：过低的溅射功率下淀积的薄膜有畸变的X射线衍射特征峰，特征峰强度小，半峰全宽大。而比较高溅射功率得到的薄膜有比较尖锐的X射线衍射特征峰，强度高和半峰全宽非常窄。研究表明，X射线衍射特征峰强度小和半峰全宽大的薄膜结构疏松，而强度高和半峰全宽非常窄的薄膜结构致密。     

反应离子镀光学薄膜的微观结构分析

用反应离子镀方法制备了ＴｉＯ２单层膜及ＴｉＯ２／ＳｉＯ２多层膜，用透射电子显微镜分别观察了由反应离子镀方法及传统蒸镀法二种不同工艺制得的ＴｉＯ２单层膜及ＴｉＯ２／ＳｉＯ２多层膜的断面结构，并对ＴｉＯ２单层膜进行了喇曼分析和卢瑟福背散射分析。     

Magnetic pole pinning at rectangular defects on MnAs/GaAs(0 0 1)

Strong magnetic poles at characteristic rectangular defects have been observed using a magnetic force microscope on a MnAs(  1 0 0) thin film with the thickness of 30 nm. The MnAs thin film was epitaxially grown on a GaAs(0 0 1) substrate. The magnetic poles were in one-arranging direction, being independent of the magnetization direction of the film. The poles were pinned at the edges of the rectangular defects until just below the Curie temperature, and formed a stable magnetic-field loop on the MnAs surface. The stability of the magnetic pole pinning shows the distinctive feature of the magnetic domain structure on the surface with a strong anisotropy, which was built in the heterostructure of MnAs and GaAs.     

CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅱ. POLY(p-PHENYLENE 2,6-NAPHTHALATE)

Confined thin film melt polymerization (CTFMP) of naphthalene chloride/hydroquinone (NCMQ, 1/1, molar)mixtures at polymerization temperatures (T_p) below ca. 300℃ resulted in relatively thick, elongated crystals. Polymerizationof NC/HQ above 300℃ between glass yielded well-formed lamellar crystals ca. 100 A thick. Phase Ⅰ and Ⅱ [001] EDpatterns were obtained for all T_p, the relative amount of phase Ⅰ increasing with T_p. Polymerization of naphthalenedicarboxylic acid/hydroquinione diacetate 1/1 mixtures at high T_p also yielded lamellar crystals that "curled up" off of thesubstrate. When the high temperature CTFMP polymerization was conducted between mica, aggregates of lamellae on-edgedeveloped but epitaxial growth did not occur. Epitaxial growth of lamellae between mica could be obtained, however, byconfined thin film solution polymerization, with both of the latter samples yielding apparently related ED patterns from adifferent unit cell than phase Ⅰ or Ⅱ. Fiber patterns, obtained from sheared samples, indicated considerably greater crystaldisorder than in the nascent crystals. Refinement of the phase Ⅰ unit cell parameters, based on the [001] and [01 1] EDpatterns, with modeling based on Cerius~2, suggests a monoclinic phase Ⅰ unit cell with a = 7.76, b = 5.71, c = 14.99 A, α = γ= 90°, β= 99.7°, ρ = 1.47 g/cm~3, space group P12_1/al.     

Coupled lubrication and Stokes flow finite elements

A method is developed for performing a local reduction of the governing physics for fluid problems with domains that contain a combination of narrow and non‐narrow regions, and the computational accuracy and performance of the method are measured. In the narrow regions of the domain, where the fluid is assumed to have no inertia and the domain height and curvature are assumed small, lubrication, or Reynolds, theory is used locally to reduce the two‐dimensional Navier–Stokes equations to the one‐dimensional Reynolds equation while retaining a high degree of accuracy in the overall solution. The Reynolds equation is coupled to the governing momentum and mass equations of the non‐narrow region with boundary conditions on the mass and momentum flux. The localized reduction technique, termed ‘stitching,’ is demonstrated on Stokes flow for various geometries of the hydrodynamic journal bearing—a non‐trivial test problem for which a known analytical solution is available. The computational advantage of the coupled Stokes–Reynolds method is illustrated on an industrially applicable fully‐flooded deformable‐roll coating example. The examples in this paper are limited to two‐dimensional Stokes flow, but extension to three‐dimensional and Navier–Stokes flow is possible. Copyright © 2003 John Wiley & Sons, Ltd.     

Thickness dependence of free‐standing thin films

Below a critical thickness, of about 60 nm, the glass transition temperature of polystyrene (PS) films decreases with film thickness, as demonstrated using free‐standing films. A geometrical model is developed here describing this phenomenon in the case of ideal (Gaussian) chains. This model, which can be considered as an application of the free volume model, assumes that the decrease of the glass transition temperature from thick to ultrathin films is due to the modification of the interpenetration between neighboring chains. The theoretical curve deduced from the model is in excellent agreement with the PS experimental results, without using any adjustable parameters. From these results, it can be concluded that new chain motions, usually buried in bulk samples, are expressed by the presence of the surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 10–17, 2007     

微型网状结构支架的力学性能研究

冠状动脉支架为圆柱形微型网状结构，直径1mm，厚度0．1mm，长度10～16mm。在经皮冠状动脉介入PCI治疗中由球囊充气撑开到直径为2．5～3．5mm的支架，在血管内承受血管壁回弹压力。为了保持血液流通支架必须保持其几何圆形。这是一个结构弹塑性稳定性问题。但是目前国际上对于支架的力学性能质量指标主要以强度性能评定而不涉及支架屈曲性能是不妥的。本文对于支架的强度和屈曲性能进行了全面的理论分析和实验研究，自行研制了智能式电子检测仪成功地对微型网状结构支架的强度和屈曲性能实现了实测实验研究。由于微型支架的离散型网状结构的特点，在实验中出现一些特殊的屈曲现象。本文研究结果对于支架的形状与性能设计的改进和力学性能质量标准规范的制订具有重要意义。