离子色谱电感耦合等离子体质谱研究痕量氯金酸在弱碱性体系中金(Ⅲ)的形态

采用离子色谱电感耦合等离子体质谱联用方法研究弱碱性体系下痕量氯金酸中Au(Ⅲ)的形态.结果表明:在弱碱性条件下,总金含量在4.0～30 ng之间,Au(Ⅲ)主要以[AuCl2( OH)2]-和[AuCl(OH)3]-的形式存在.与较高含量的氯金酸溶渡相比,痕量氯金酸溶液中的[AuCl2(OH)2]-至少可以在pH 7.0～10.0范围内存在.溶液外加的Cl-可使[AuCl2 (OH)2]-含量升高同时降低[AuCl (OH)3]-含量;当pH=7.0或Cl-浓度高于0.050 mol/L,会产生不随色谱流出的金络合物,根据水解过程推断该络合物为[AuC13 (OH)]-.在pH 8.0～10.0,Cl-浓度在0.000～0.020 mol/L时,[AuCl2(OH)2]-+OH-=[AuCl (OH)3]-+Cl-的水解平衡常数为不定值,说明痕量氯金酸的水解不仅受pH值和Cl-浓度影响,还受其它因素影响.     

纳米银掺杂炭气凝胶修饰电极对卤素离子的电化学响应

首次以新型的纳米银掺杂炭气凝胶为材料,制备了一种新型纳米银炭电极,并考察了该电极对卤素离子的电化学响应。在0.1 mol/L的KNO3中,用微分脉冲伏安法对含Cl-的溶液以及卤素离子共存时的溶液进行测定,结果表明:峰电流与Cl-浓度呈线性关系,线性范围为2.0×10-7-4.2×10-5mol/L;检出限为1.2×10-8mol/L。此外响应电流与Cl-、Br-、I-3种离子的总浓度在6.0×10-7-1.2×10-5mol/L范围内呈线性关系。结果表明,纳米银掺杂炭气凝胶修饰电极可望用于痕量卤素离子的测定。     

HCO_3~-浓度对油气田中CO_2腐蚀的影响

应用动电位扫描和失重法研究HCO3-对油气田CO2腐蚀的影响.实验表明,当HCO3-浓度低于0.042 mol/L时,随着HCO3-浓度的增加,溶液pH升高,H+的还原速率(阴极电流密度)下降;HCO3-浓度增至0.126 mol/L时,溶液中的H2CO3、HCO3-的直接还原占主导地位,故阴极过程随HCO3-浓度的上升而加速,对阳极过程,在HCO3-浓度低于0.042 mol/L下,主要为活化过程,而且其阳极溶解电流(密度)随HCO3-浓度的增加而下降;HCO3-浓度增至0.126 mol/L时,阳极过程出现明显的活化-钝化行为.高温高压腐蚀试验显示,材料的腐蚀速率随介质HCO3-浓度的增加而下降.SEM、EDS、XRD分析表明,在较低的HCO3-浓度下,腐蚀产物膜的主要成分为FeCO3晶体,HCO3-浓度较高时,则腐蚀产物主要为Ca、Mg的化合物,并形成Ca(Fe,Mg)(CO3)2复盐.在高pH值下,Ca2+、Mg2+比Fe2+更容易沉积.     

扫描微电极法原位测量2024Al合金表面微区Cl~-浓度分布

应用自研制扫描微电极测量系统和扫描微Ag/AgCl复合电极 ,原位测量含Cl- 溶液中 ,2 0 2 4Al合金在其局部腐蚀发生发展过程中金属 /溶液界面微区Cl- 离子的浓度分布 ,考察金属 /溶液界面微区Cl- 浓度分布对Al合金表面局部腐蚀行为的影响 .结果表明 ,扫描Ag/AgCl探针可实时跟踪腐蚀过程中金属表面氯离子浓度分布的动态行为 .当 2 0 2 4Al合金浸渍于含Cl- 溶液中 ,Cl- 离子在Al合金 /溶液界面呈不均匀分布 ,Cl- 主要在第 2相颗粒和铝基交界区域发生优先吸附和累积 ,从而促进局部腐蚀的发生和发展     

氯离子电极的研制及应用研究

以戊巴比妥氯化汞(Ⅱ)为载体,制备了PVC液态膜氯离子选择性电极.电极对Cl-离子呈现高的选择性,其选择顺序为I-＞Br-～SCN-～Salicylate-＞＞ClO-4＞NO-3＞F-＞H2PO-4＞HCO-3＞SO2-4.测定了电极对常见阴离子的选择性,除I-、Br-与SCN-有干扰外,其它阴离子均无明显的干扰;25℃ 时, 在0.05 mol·L-1 H3PO4-NaH2PO4(pH 4.1)溶液中,Cl-离子浓度在6.0 ×10-3～3.5×10-6 mol·L-1 呈线性响应,斜率为57.6 ±2 mV/decade,检出限为2.0 ×10-6 mol·L-1.该法用于氯仿光催化降解微量Cl-离子的测定,取得满意结果.     

吡啶类碳离子液体电极对酚磺乙胺的电化学行为及其分析应用

用离子液体1-丁基吡啶六氟磷酸盐(BuPyPF6)作为粘合剂构置了碳离子液体修饰电极(BuPyPF6-CILE).在0.05 mol/L H2SO4溶液中,用循环伏安法研究了在BuPyPF6-CILE和传统碳糊电极(TCPE)上酚磺乙胺(ESL)的电化学行为,建立了测定尿样和血清样品中ESL含量的新方法.ESL在BuPyPF6-CILE上的氧化峰电流响应是其在TCPE上的8.7倍,峰电位差降低到0.101 V,电子转移速率常数Ks=0.544 s-1,电极表面平均吸附量为1.66×10-9 mol·cm2.ESL的氧化电流与其浓度在8.0×10-8～2.0×10-6mol/L和5.0×10-6～1.0×10-4mol/L范围内呈线性关系,检出限为3×10-8mol/L(S/N=3).连续5次测定2.0×10-6mol/L ESL溶液的RSD为1.5%.     

模拟混凝土孔溶液中钢筋电化学噪音测量及小波分析

电化学噪音(Electrochemical Noise,ECN)测量可用于在无电信号扰动条件下检测腐蚀体系的暂态行为,获得有关腐蚀类型和腐蚀速率的信息.小波分析不需要对ECN作稳态假设,并同时具有时间分辨和频率分辨的特点,在ECN信号处理中表现出一定的优势.本工作考察了氯离子对钢筋在模拟混凝土孔溶液中电化学噪音的影响,并采用离散小波变换(DWT)及能量分布图(EDP)分析ECN信号的时间～频率特征.结果表明,在含NaCl0.0001mol/L的饱和Ca(OH)2溶液中,时间常数为16～32s的暂态占优势;在Cl-浓度更高的溶液中,去钝化趋势为主导事件,表明钢筋在SPS溶液中活化/钝化的临界Cl-浓度介于10-4～10-3mol/L.     

离子选择性电极测定溶液中Br-时去除Cl-的干扰

本文研究了用离子选择性电极法测定溶液中的Br-时,共存离子Cl-在5.0×10-5~1.0×10-2mol/L浓度范围内的干扰情况。同时,应用Matlab建立线性回归方程用于实际分析,取得满意结果。     

Ru(bipy)2+3-CO2-3-SO2-3-KClO3体系化学发光法测定空气中的二氧化硫

提出了Ru(bipy) 2+ 3-CO 2- 3-SO 2- 3-KClO 3体系化学发光法测定溶液中亚硫酸盐的方法.SO 2- 3浓度与化学发光强度在1.0×10-7～1.0×10-4 mol/L 范围内成正比,检出限为8.76×10-8 mol/L,对1.0×10-4 mol/L SO2-3溶液6次测定的相对标准偏差为2.9%.该法用三乙醇胺作为吸收液,成功地用于测定空气中二氧化硫的含量,结果满意.     

聚吡咯/聚苯胺复合型导电聚合物防腐蚀性能

采用循环伏安法,在含吡咯和苯胺的0.3 mol/L草酸水溶液中制备了聚吡咯/聚苯胺(PPy/Pani)的复合型导电聚合膜。采用红外光谱、极化曲线、自腐蚀电位-时间曲线、扫描电子显微镜和电化学阻抗谱研究了共聚膜的防腐蚀性能。结果表明,在1 mol/L H2SO4中,PPy、Pani与不锈钢基体发生氧化还原反应,促进不锈钢表面发生钝化;当苯胺与吡咯浓度比为1∶3时,制备得到的复合型导电聚合膜所保护的不锈钢自腐蚀电流最小,自腐蚀电位最高,保护时间最长。PPy、Pani及其共聚膜在3.5%NaCl溶液中电化学阻抗谱表明,所制备的PPy、Pani及其共聚物膜与不锈钢基体发生氧化还原反应,使其表面钝化;当Cl-到达不锈钢表面时,破坏钝化膜导致不锈钢腐蚀。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.