异相晶核法液相合成金红石型TiO2纳米晶

分别以SnCl₂·2H₂O和SnCl₄·5H₂O为锡源,采用胶溶晶核法,经沉淀和胶溶过程,在液相中一步合成了金红石型TiO₂.详细考察了各种胶溶条件对产物结构的影响,并通过两种锡源实验结果的比较对异相晶核法中两种锡源的成晶机理进行了分析.所合成的金红石型TiO₂晶粒度为20～50nm,两种方法获得完全金红石型TiO₂所需引入SnO₂的最低物质的量的分数分别为10%和8%.     

TiO2纳米粒子制备方法对其光催化活性的影响

分别用胶溶法、金属醇盐水解法和低温水解法制备了TiO2纳米粒子;采用XRD和BET技术,测试了TiO2粒子的粒径、晶型及表面积。以庚烷的气相光催化氧化为探针反应,考察了不同方法、不同温度处理的TiO2粒子的光催化活性。结果表明,以胶溶法和金属醇盐水解法制备的TiO2粒子,随焙烧温度的增加TiO2粒子长大,晶型由锐钛矿向金红石型转变,光催化活性降低。用低温水解法,可在低温下制得金红石型TiO2粒子,但其催化活性很低。说明由原料和制备方法所决定的TiO2粒子的物理化学性质,影响其光催化行为。锐钛矿型TiO2粒子催化活性较金红石型TiO2好。这是由于前者的表面羟基含量较高且带隙能较大的缘故。     

石墨/氧化锡/活性炭锂离子电池负极材料的合成及性能

采用液相法,以SnCl2·2H2O、石墨、活性炭为原料,在油浴中共热合成石墨/氧化锡/活性炭复合材料.通过XRD和电化学测试对材料进行了表征.结果表明,样品中含有石墨和金红石SnO2·这种材料作为锂离子电池负极材料具有良好的充放电循环性能.     

La2O3掺杂TiO2光催化剂的制备和性能

采用溶胶-凝胶法制备了La2O3掺杂TiO2纳米光催化剂，并通过XRD、TEM、BET和XPS等手段进行了表征．掺入La2O3后，阻止了TiO2从锐钛矿晶型向金红石晶型的转变，使TiO2的粒径减小，比表面积增大．以甲基橙为光催化降解反应模型化合物，考察了光催化剂的活性．测定了甲基橙在纯TiO2和La2O3掺杂TiO2光催化剂上的吸附常数．考察了pH、H2O2对降解性能的影响．讨论了光催化活性与催化剂性质的关系．     

纳米Ni/TiO_2粉体的制备及其光催化性能

以四氯化钛为主要原料,通过溶胶法合成了纳米TiO2和Ni/TiO2粉体。研究发现掺杂镍,能够有效延缓锐钛矿型TiO2向金红石型TiO2转变,提高Ni/TiO2粉体的催化活性;在500℃焙烧的Ni/TiO2催化剂,能较好催化溴甲酚绿染料在紫外光下降解。     

低温液相制备金红石型TiO2纳米晶须

目前，已有多种控制TiO2形貌及晶须生长的方法，如模板合成、超分子组装、声化学合成液相法及固相合成等，其中，液相法是最为廉价和简单的方法．为此，近期采用低温液相法合成金红石型TiO2受到了极大的关注．本文在以前工作的基础上，采用改进的实验方法通过在低温陈化一定浓度的TiCl4水溶液直接获得了金红石型TiO2纳米晶须，并对产物进行了初步表征．     

Sol-gel自蔓燃法控制合成二氧化钛纳米粉体及性能

采用化学络合溶胶-凝胶法,结合自蔓燃合成工艺制备了结构可控、分散性良好的TiO2纳米粉体.考察了原料组成、凝胶膨胀程度和温度机制对粉体结构、分散性的影响,用漫反射光谱测试了所制备粉体的光吸收性能. 结果表明,将原料中氧化剂与还原剂的摩尔比从2增加到7,在600 ℃的煅烧温度下可以得到金红石含量在25％～68.2％之间的TiO2,这些结构不同的粉体粒度为30 nm左右;凝胶前驱体经过150 ℃充分膨胀炭化,能有效阻止胶粒间氢键的形成,并且能够防止因毛细管作用而导致的凝胶网络坍塌,从而得到单分散无团聚粉体;提高煅烧温度,金红石含量增多、颗粒粒度增大,800 ℃时出现团聚体;用该工艺制备的粉体的光吸收范围发生明显红移,与市售金红石型TiO2相比,反光率下降10％以上;金红石含量为55.5％的混晶型粉体显示出最好的光吸收性能.     

WO3-TiO2薄膜型复合光催化剂的制备和性能

 采用溶胶－凝胶法在多孔钛片上制备了WO3－TiO2薄膜型复合光催化剂,并用甲基橙的光催化降解反应对所得薄膜型催化剂的活性进行了评价．实验结果表明：x（W）＝0．5％,涂覆层数为3层,在500℃焙烧1h的WO3－TiO2薄膜型光催化剂的活性最高,比纯TiO2薄膜高出96．7％．此时多孔钛片上负载的TiO2以锐钛矿和金红石两种晶形存在,表明适量W的掺入可使TiO2的相转变温度显著降低．     

氢电弧等离子体法制备纳米钛粒子脱硫性能研究

使用H2 Ar等离子体法制备纳米Ti粒子并用球磨法负载到载体上，500℃焙烧后制成纳米TiO2脱硫催化剂．利用TEM、BET、XRD等手段，对催化剂进行了表征．焙烧后纳米钛粒子主要以金红石型TiO2存在．在不同温度、空速、SO2／CS2和老化条件下，进行CS2的水解实验证明，物理法制备的纳米TiO2／Al2O3催化剂具有较高的耐硫酸盐化中毒能力．     

TiO2/蒙脱石纳米复合物中TiO2的结构相变

以钛酸丁酯和季铵盐改性有机蒙脱石为原料,采用原位水解法和原位脱羟法制备了TiO2/蒙脱石纳米复合物。采用X射线衍射(XRD)、拉曼光谱(Raman)表征了不同焙烧温度下TiO2/蒙脱石纳米复合物中TiO2的结构相变,并与不同焙烧温度下纯TiO2的结构相变进行对比。结果发现TiO2/蒙脱石纳米复合物中TiO2从锐钛矿相开始转变为金红石的最低温度要比纯TiO2从锐钛矿开始相转变为金红石的最低温度高200℃,且在焙烧温度1 200℃时还存在锐钛矿相,而纯TiO2在焙烧温度800℃时就全部转换为金红石相。TiO2/蒙脱石纳米复合物中TiO2和纯TiO2的平均晶粒度都随焙烧温度升高而增大,但TiO2/蒙脱石纳米复合物中TiO2的平均晶粒度要小于相同温度下焙烧纯TiO2的平均晶粒度。表明蒙脱石结构层的硅氧结构抑制了TiO2晶型由锐钛矿相向金红石相的转变,进而使相变温度升高,同时阻碍了晶体的生长。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.