液相沉淀法制备稀土-锆固溶体及其性能研究

采用液相沉淀法制备了Ce0.6Zr0.3La0.05Y0.05O2固溶体。通过BET,XRD,SEM,程序升温还原和氧脉冲吸附等方法对合成产品性能进行了表征。研究了前驱体的形态、高温水热处理、表面处理以及后期固溶体的还原处理对固溶体性能的影响。其中前驱体的高温水热处理和固溶体的还原处理对固溶体的催化性能有很大的影响。200℃水热处理制得的固溶体经1000℃老化4 h后,比表面积为25.3 m2.g-1,孔容为0.21 cm3.g-1,经800℃还原处理3 h后储氧量为478.3μmol.g-1,显示了较高的比表面积和储氧能力的高温稳定性。     

高热稳定性、 高比表面积低铈型铈锆钇储氧材料的制备及其性能研究

采用氨水 碳酸铵混合沉淀剂制备了低铈型铈锆钇三组分储氧材料. 采用X射线衍射、 BET、 氧脉冲吸附和H2程序升温还原(H2-TPR)等技术对材料的晶体结构、 比表面积、 孔结构、 储氧性能和还原性能进行了研究. 结果表明， 该材料经873 K焙烧4 h后比表面积达到116.8 m2/g, 孔容达到0.30 cm3/g, 经1 273 K老化10 h后, 比表面积和孔容仍然保持在68.1 m2/g和 0.22 cm3/g. 由XRD结果可知, 材料的物相组成为四方相的Zr0.84 Ce0.16 O2, 在热处理过程中物相结构稳定. 氧脉冲吸附和程序升温还原的结果表明, 材料储氧性能保持较好.     

大比表面积铈锆氧化物固溶体的制备

采用共沉淀法制备铈、锆氧化物固溶体.发现以适当配比的(NH4)HCO3和NH3*H2O混合溶液作为沉淀剂,同时控制沉淀过成中的反应条件,所得到的沉淀在较低的温度(400 ℃)下焙烧即可形成铈、锆氧化物固溶体.该固溶体具有较大的比表面积和高的储氧能力.形成沉淀后添加适量表面活性剂,可进一步提高产品的比表面积而对其还原行为和储氧性能几乎无影响.对制得的氧化物以X-射线衍射、程序升温还原、氧的脉冲滴定和液氮物理吸附等方法进行了表征.     

不同铈添加量对CeO2-ZrO2-Al2O3材料性能的影响

采用共沉淀法制备了一系列不同铈添加量的CeO2-ZrO2-Al2O3(CZA)储氧材料,并通过XRD、低温N2吸附-脱附、氧脉冲吸附(OSC)和H2-TPR等手段进行了表征。XRD结果表明,在1 000和1 100℃高温焙烧后,当CeO2添加量为8%时样品具有最好的结构稳定性能。N2吸附-脱附结果表明,CeO2添加量为8%时样品具有最好的织构性能,1 000℃时,比表面积和孔容分别为:136.6 m2.g-1和0.38 mL.g-1;1 100℃时,比表面积和孔容分别为:83.7 m2.g-1和0.23 mL.g-1。OSC结果显示,CeO2添加量为8%时样品具有最大的储氧量,1 000℃和1 100℃分别为70μmol.g-1和31μmol.g-1。H2-TPR结果表明,CeO2添加量为8%时样品具有最佳的还原性能。     

沉淀方法对CeO2-ZrO2系储氧材料性能的影响

利用不同沉淀方法制备了一系列CeO2-ZrO2系储氧材料,并应用BET、XRD、TPR及其储氧性能测定等方法对储氧材料进行了研究.结果表明,不同的沉淀方法对样品的结构和性能有重要的影响.并流法可得到耐高温,储氧性能好,比表面积高的储氧材料;正滴法所得样品储氧量低但稳定,其比表面积抗老化性能差;反滴法所制备的样品储氧性能好,老化后比表面积较低.三种沉淀方法均可形成CeO2-ZrO2固溶体,材料的还原性能取决于比表面积,但与储氧性能无直接关系.     

高性能Ce_(0.5)Zr_(0.5)O_2稀土储氧材料的制备及其负载的单Pd三效催化剂

以碳酸铵水溶液为沉淀剂,改变前驱体盐溶液的浓度,采用共沉淀法制得了一系列Ce0.5Zr0.5O2固溶体材料.以此系列材料为载体制备了负载型单Pd三效催化剂,并利用N2吸附-脱附、X射线衍射、储氧量测定和程序升温还原等技术对材料了进行表征.结果表明,所制Ce0.5Zr0.5O2材料具有优异的抗高温老化性能和氧化还原性能,且盐溶液的浓度对材料及其负载型Pd三效催化剂性能的影响较大.当盐溶液浓度为0.3mol/L时,制备材料的织构性能最佳,经1000oC老化5h后其比表面积和孔体积分别为53.0m2/g和0.17cm3/g.所制得的三效催化剂对CO,NO和C3H8具有低的起燃温度和完全转化温度,表现出最佳的催化性能,具有良好的应用前景.     

掺杂Mn对CeO2-ZrO2-Al2O3材料性质的影响

采用共沉淀法制备了一系列Mn掺杂摩尔分数为0～5%的CeO2-ZrO2-Al2O3(CZA)复合氧化物, 并采用BET, OSC, XRD, XPS, H2-TPR等方法对所制备的材料进行了表征. 结果表明, 所制备的材料均形成了稳定的CZA固溶体, 尤其是Mn掺杂0.5%的材料在600和1000 ℃焙烧后均表现出最好的织构性能. OSC和H2-TPR的结果表明, Mn掺杂量≤1%时, 氧在材料中的体相移动是材料储氧和被还原的速控步骤, 并且Mn的掺杂量为0.2%时, 储氧量最大, 材料的还原温度也最低; Mn掺杂量>1%时, Mn物种对材料储氧和被还原的作用显著. XPS结果表明, Mn在焙烧过程中会迁移向表面, 结合H2-TPR结果可知, 新鲜样品表面的MnOx物种主要为Mn2O3, 而老化样品主要为Mn3O4.     

负载型Pd三效催化剂：载体CeO2-ZrO2-BaO的制备及催化性能

制备了不同BaO含量的CeO2-ZrO2储氧材料,并以此材料为载体浸渍H2PdCl6制得三效催化剂.结果表明,不论新鲜还是1 000 ℃老化状态下,以10%BaO添加CeO2-ZrO2储氧材料制备的Pd三效催化剂活性最佳,起燃和完全转化温度最低.XPS结果证实,10%BaO添加.通过稳定PdO活性组分并改变其电子环境使得催化剂有最佳活性.而随着BaO含量持续增加,Pd活件组分相对处于较氧化状态.储氧量、低温N2吸附-脱附测试以及XRD测试结果均表明10%BaO添加的材料储氧量,比表面积以及孔容均最大,而且有适应三效催化的孔径.这些结果均有助于以其制备的Pd三效催化剂获得更好的活性以及热稳定性.     

满足欧Ⅲ排放标准的汽油车中偶催化剂

 制备了高性能稀土储氧材料Ce0.5Zr0.4Y0.1O2和镧稳定的氧化铝(La-Al2O3), 并以此为基础制备了中偶汽油车尾气净化催化剂. 经老化前后的性能检测证实,稀土储氧材料具有优异的织构性能和储氧性能且高温稳定性优良; La-Al2O3具有优异的织构性能及优异的抗高温老化性能. 中偶催化剂对HC, CO和NOx具有优异的低温活性、抗高温老化性能和低的劣化系数. 捷达-MT型汽油车排放检测表明该催化剂能够满足欧Ⅲ排放标准.     

镧、锰掺杂改性CeO2-ZrO2-Al2O3固溶体的性能

采用共沉淀法制备了一系列La, Mn共掺杂的CeO2-ZrO2-A12O3(CZA)复合氧化物, 采用BET, XRD, H2-TPR, XPS和XRF等方法对样品进行表征. 结果表明, 全部样品均形成了稳定的CZA固溶体, 经600 ℃焙烧后表现出良好的织构性能, 1000 ℃老化后, La, Mn共掺杂样品具有最佳的高温稳定性; H2-TPR测试表明, La, Mn之间存在正协同效应, 共掺杂的样品具有最佳的低温还原性能和高温稳定性; XPS结果表明, 掺杂La可有效抑制在焙烧过程中Mn向表面的迁移, 从而保持较高的表面吸附氧浓度.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

解决能源问题的新途径——光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。