Gd2O3:Er3+上转换发光粉在染料敏化太阳电池中的应用

采用沉淀-煅烧法制备了Gd₂O₃:Er³⁺上转换发光粉,通过X射线衍射、扫描电子显微镜、能谱和荧光光谱对其进行了表征,并利用该发光粉具有上转换发光的特性将其应用于染料敏化太阳电池(DSSC)。结果表明,管状Gd₂O₃:Er³⁺上转换发光粉可增加电池对太阳光的吸收范围和吸收效率,提高电池的光电流和光电压。研究了掺杂量对电池性能的影响,当掺杂量为5wt%时,光电转换效率从5.93%升高到7.55%,提高约27%。     

双层结构CeO2光阳极在染料敏化太阳能电池中的应用

利用水热法合成核壳结构Au@SiO₂@CeO₂纳米微球,制备了一系列双层结构复合光阳极并应用于染料敏化太阳能电池(DSSC)。研究表明：当CeO₂纳米微球和核壳结构Au@SiO₂@CeO₂纳米微球应用于DSSC光阳极散射层时,电池的光电转化效率有了显著提高。相对于纯 TiO₂ (P25)光阳极,P25/CeO₂纳米球光阳极电池的 DSSC 光电性能提高了 15.3%,P25/Au@SiO₂@CeO₂纳米球光阳极电池的光电性能提高了27.9%。DSSC光电性能的提高主要归因于2个方面：一方面,Au纳米粒子的表面等离子体共振效应有效提高了光阳极薄膜的光散射效应。另一方面,CeO₂具有较高的染料负载能力,核壳球形结构具有较高的比表面积,增强了光的散射效应,提高了电子传输能力。     

表面活性剂对染料敏化太阳能电池光电性能的提高

在硝酸/醋酸(HNO₃/HAc)的水溶液中分别加入十二烷基苯磺酸钠(DBS)、十六烷基三甲基溴化铵(CTAB)、吐温20等不同类型的表面活性剂来水解钛酸四正丁酯制得前驱体溶液,通过水热法制备纳晶TiO₂,并组装成染料敏化太阳能电池(DSSC)。通过XRD、SEM和UV-Vis对纳晶TiO₂薄膜进行表征,并对DSSC进行光电流-光电压(I-V)曲线的测试,研究了不同类型的表面活性剂和不同浓度的CTAB对DSSC光电性能的影响。结果表明：加入阳离子表面活性剂CTAB时提高了DSSC的光电性能,而加入阴离子表面活性剂DBS和非离子表面活性剂吐温20时,DSSC的光电性能反而降低。随着CTAB浓度的增加,电池的光电性能先提高后下降,当c_CTAB=0.08 mol·L^-1时,DSSC的光电转化效率最高为5.76%,比不添加表面活性剂制备的纳晶TiO₂所组装的DSSC的光电转化效率提高了约18%。     

TiO2纳米微球的制备及在染料敏化太阳能电池中的应用

以四氯化钛、盐酸为原料,制备出花状TiO₂纳米微球,利用扫描电子显微镜（SEM）、X射线衍射（XRD）等测试方法,对样品的结构和形貌进行了表征。为了提高TiO₂微球电池的光电性能,利用TiO₂微球作为反射层构造了双层结构的薄膜电极,结果表明,双层结构染料敏化太阳能电池在100 mW·cm^-2（1.5 G）光照条件下,短路光电流J_sc为17.64 mA·cm^-2,开路光电压Voc为0.74 V,填充因子FF为0.63和光电转化效率η为8.33%。相比TiO₂微球制备的太阳能电池,双层结构染料敏化太阳能电池光电转化效率提高至5.3倍。最后对电极中染料的吸附量、电极的光散射性能和电池的电化学阻抗做了进一步研究和分析,研究表明,双层结构电池增强光的捕获能力,从而提高光伏性能。     

改进型溶胶-凝胶法制备粒径可调高染料吸附量TiO2微球及其在染敏电池光散射层中的应用

利用改进型的溶胶-凝胶法, 制得了由锐钛矿相纳米颗粒组成的TiO₂多孔微纳小球。通过调节前驱物浓度, 合成出粒径可控的尺寸分别为100, 175, 225, 475 nm的TiO₂微纳小球, 并通过电泳沉积法将合成出的小球作为光散射层引入到染料敏化太阳电池(DSSC)中。由于这种微纳小球在具备良好的光散射性能的同时也具备较高的染料吸附量, 因此相较于基于纳米颗粒的单层结构的DSSC拥有更高的光电转换效率。通过比较分析, 粒径尺寸为475 nm的微球作为光散射层的DSSC光电转换效率可以达到6.3%, 较之于基于纳米颗粒的DSSC提高了30%。     

MnWO4/生物质衍生碳纳米复合催化剂的制备及催化性能

通过共沉淀法合成了双金属氧化物MnWO₄镶嵌生物质衍生碳（MnWO₄/BC）纳米复合催化剂,并将其作为对电极（counter electrode,CE）催化剂组装了染料敏化太阳能电池（dye-sensitized solar cell,DSSC）,探究了MnWO₄/BC在非碘体系中的催化性能和光伏性能。结果表明：在铜氧化还原（Cu²⁺/Cu⁺）电对DSSC中获得的光电能量转换效率（power conversion efficiency,PCE）为3.57%（D35）和1.59%（Y123）,高于Pt电极的PCE（3.12%,1.16%）;50次连续循环伏安测试表明,MnWO₄/BC催化剂具有较好的电化学稳定性。     

3-氨基丙基三甲氧基硅烷自组装提高染料敏化太阳能电池的效率

以3-氨基丙基三甲氧基硅烷(APTS)修饰的二氧化钛为负极制备的染料敏化太阳能电池在100 mW·cm^-2的模拟太阳光照下的短路电流、开路电压、光电转换效率分别为18.32 mA·cm^-2、775.9 mV、9.15%. 而没有经过ATPS修饰的电池三项性能参数分别为18.08 mA·cm^-2、749.9 mV、7.70%, 修饰后电池的光电转换效率提高了18.8%, 同时填充因子由0.57提高为0.64. 暗电流-电压曲线显示起始电压从-0.30 V变化到-0.40 V, 表明二氧化钛电极和电解液之间的暗反应得到了有效抑制, APTS作为阻挡层减少了二氧化钛电极表面的缺陷与表面态. 另外, 通过实验设计, 将APTS与染料层-层自组装于二氧化钛电极上, 通过X射线光电子能谱(XPS)研究了二氧化钛层、APTS、染料的作用形式. 定性与定量结果表明: APTS中的乙氧基部分脱除后形成了Si―O―Ti单桥或者双桥键, 钌染料cis-Ru(dcpyH₂)₂(SCN)₂通过分子中的部分―COOH与APTS中的―NH₂形成的静电作用力吸附在TiO₂电极上. 傅里叶变换红外(FT-IR)光谱的结果进一步证明了这种分子间作用.     

含有TiO2刺球散射中心光阳极的设计及其在染料敏化太阳能电池的应用

采用水热法制备了一种刺球状TiO₂（NT）,将其作为光散射中心,与纳米晶TiO₂混合,制备成一种底层为P25薄膜（作为染料吸收层）,上层为添加NT散射层的混合结构的薄膜光阳极。探讨了NT添加量对薄膜性能的影响,实验结果表明,当NT与P25粉体的质量比为35%时电池光电性能最优,电池短路光电流密度为14.30 mA·cm^-2,其光电转换效率达到7.38%。质量比继续增大,当达到50%时电池性能有所下降,光电转换效率降为5.99%,同时染料吸附量也由73.2 μmol·cm^-2降到70.1 μmol·cm^-2。这表明过量的大颗粒TiO₂刺球散射中心会减少光阳极的比表面积从而降低染料的有效吸附量,并且还会引起不必要的反向散射,只有适量的散射中心才能得到最佳性能的太阳能电池器件。     

MoS2/CNFs对电极膜厚对染料敏化太阳能电池性能影响

通过静电纺丝技术和水热法成功获得了碳纳米纤维负载二维层状硫化钼（MoS₂/CNFs）,将其作为对电极组装的染料敏化太阳能电池（DSSCs）表现出优异的电化学特性。在DSSCs制备过程中,对电极膜厚对电池性能有很大影响,所以本文重点探究了喷涂法制备的对电极膜厚对其组装的染料敏化电池光电性能影响,获得最佳对电极膜厚。实验结果表明当MoS₂/CNFs复合对电极材料膜厚为8 μm时,电池光电转换效率达到最大值7.78%。     

TiCl4水解法制备的阻挡层对染料敏化太阳能电池光电性能的影响

通过不同浓度的TiCl₄溶液水解, 在光阳极导电玻璃(FTO)基底上制备了阻挡层薄膜, 以此来抑制FTO表面的光生电子与I₃^-之间的复合反应, 采用X射线光电子能谱(XPS)和X射线衍射分别测试了阻挡层薄膜的组成, 用场发射扫描电子显微镜(FE-SEM)和紫外-可见(UV-Vis)分光光度计测试了阻挡层的形貌和对光的透过率, 在AM1.5和暗环境下分别测试了染料敏化太阳能电池(DSSC)的光电性能. 实验结果表明: 用此方法可以获得由TiO₂粒子组成的阻挡层薄膜; 阻挡层薄膜的形貌随着TiCl₄溶液浓度的增加而改变, 它的厚度随着TiCl₄溶液浓度的增加而增加; 引入阻挡层后, FTO对光的透过率都会下降; 这一薄膜的引入可以提高电池的光电性能, 用0.04 mol·L^-1的TiCl₄溶液制备的阻挡层对暗电流的抑制作用最为明显, 电池在AM1.5的条件下测试, 转换效率最高达7.84%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.