乙酸稀土盐催化缩聚合成聚(对苯二甲酸乙二酯-co-己二酸乙二酯)

合成了一系列乙酸稀土盐(乙酸钇,乙酸镧,乙酸钕,乙酸镝),作为单组分催化剂,采用熔融缩聚法催化对苯二甲酸二甲酯、乙二醇和1,6-己二酸的共缩聚反应,制备了芳香族脂肪族共聚酯——聚(对苯二甲酸乙二酯-co-己二酸乙二酯)(PETA).通过1H-NMR,SEC,DSC及力学性能测试表征了聚合物的序列结构,分子量及分布,热性能及机械性能.结果表明,乙酸稀土盐单组分可催化共缩聚反应,效果优良,能够合成高分子量和较窄分子量分布的共聚酯,共聚酯具有较高的拉伸强度和断裂伸长率.     

聚酯-聚酯多嵌段共聚物的合成及其动态力学性能

聚酯-聚醚多嵌段共聚物的动态力学性能谱上有两个T_8,不宜做阻尼材料。本文报道聚对苯二甲酸乙二醇酯(PET)-端羟基聚己二酸乙二醇酯(PEA)共聚物(简称嵌段共聚酯),比聚醚-聚酯多嵌段共聚物有更好的相容性。我们研究了PEA的分子量,间苯二甲酸的用量对嵌段共聚酯的结晶度,以及结晶度对嵌段共聚酯的动态力学性能的影响。     

聚(对苯二甲酸丁二醇酯-co-对苯二甲酸环己烷二甲醇酯)-b-聚乙二醇嵌段共聚物的合成与表征

用熔融缩聚法合成了一系列聚(对苯二甲酸丁二醇酯-co-对苯二甲酸环己烷二甲醇酯)-b-聚乙二醇嵌段共聚物(PBCG),用NMR,GPC,DSC,TGA及力学性能测试等方法表征了材料的结构与性能.GPC分析显示,共聚物分子量均具有较为对称的单峰分布,多分散性指数低于1.70.¹³CNMR谱结果表明,随PCT摩尔分数(x_PCT)从10%增至60%,PBT平均序列长度由4.02降到1.41;而PCT平均序列长度则由1.17升至2.50,二者呈无规分布.受硬段平均序列长度及结晶能力影响,硬段熔点及结晶度在x_PCT为20%～30%处均达到最小值,可能是硬段间形成共晶所致.TGA分析显示,引入芳香族聚酯组分PCT确可提高材料的热稳定性.力学性能测试说明,降低结晶度有利于提高材料的断裂延伸率,相反,则有助于增强弹性模量,断裂强度及屈服强度.     

聚（琥珀酸丁二醇酯-共-富马酸丁二醇酯）的合成及其双羟基化反应研究

以琥珀酸、富马酸、丁二醇为原料，用共缩聚的方法合成了一系列高分子量聚 （琥珀酸丁二醇酯-共-富马酸丁二醇酯）。然后在催化剂四氧化锇和N-甲基吗啉- N-氧化物以及水存在下，使高分子主链中富马酸丁二醇酯共聚单元的碳碳不饱和双 键发生羟基化反应得到含有亲水性侧羟基的功能性聚酯。对上述合成的生物降解性 高分子运用核磁共振（NMR）、红外（FT-IR）、热分析等方法进行了结构与物理性 能表征。     

生物可降解共聚物聚丁二酸/对苯二甲酸丁二醇酯(PBST)的序列结构及结晶性研究

制备了高分子量的聚丁二酸丁二醇酯,并通过与对苯二甲酸二甲酯的无规共聚调节其生物可降解性及力学性能,得到了具有优良机械性能和不同生物降解速度的一系列共聚物,并对共聚物序列结构、热力学性能、结晶性进行了研究.结果表明,该共聚物为无规共聚物,PBS和PBT分别结晶.共聚物的结晶熔点符合无规共聚物的Flory方程.     

聚对苯二甲酸乙二醇酯/聚乙二醇醚插层嵌段共聚物的结晶性能

合成了不同用量、不同分子量的聚乙二醇醚(PEG)或聚丁二醇醚(PTMC)与聚对苯二甲酸乙二醇酯(PET)/蒙脱土(MMT)的嵌段共聚物。研究了MMT在共聚物中的分散状态及PEG或PTMG对PET/MMT插层聚合物结晶性能的影响。结果表明,MMT在共聚物中以纳米尺寸分散;加入PEG或PTMG增强了聚酯链段的柔顺性,使共聚物熔体降温过程的结晶温度提高,冷结晶温度降低,即插层嵌段共聚物的结晶速率提高;在合成的共聚物中,分子量为2000,用量为DMT的6%的PEG对插层共聚物结晶速率的促进作用最大     

ε-己内酯与L-丙交酯共聚物的合成及其电纺丝加工初步研究

采用辛酸亚锡为催化剂,1,4-丁二醇为引发剂,制备了不同组成、不同分子量的ε-己内酯/L-丙交酯共聚物,并用GPC、FTIR、1H-NMR、DSC和XRD等分析方法表征了该共聚物的结构.结果表明通过改变初始投料中两单体的比例,可以调节共聚酯的分子结构;调节单体与引发剂的比例,可以调节共聚酯分子量,进而影响到其形态与性质.采用高分子量的共聚物进行电纺丝加工,得到了微米级超细纤维无纺布,由SEM可观察到纤维之间有不同程度的粘结.在孔隙率约为75%左右的情况下,该无纺布的抗拉强度可达6.1MPa,延伸率为500%.     

ε-己内酯与L-丙交酯共聚物的合成及其电纺丝加工初步研究

 采用辛酸亚锡为催化剂,1,4-丁二醇为引发剂,制备了不同组成、不同分子量的ε-己内酯/L-丙交酯共聚物,并用GPC、FTIR、¹H-NMR、DSC和XRD等分析方法表征了该共聚物的结构.结果表明通过改变初始投料中两单体的比例,可以调节共聚酯的分子结构;调节单体与引发剂的比例,可以调节共聚酯分子量,进而影响到其形态与性质.采用高分子量的共聚物进行电纺丝加工,得到了微米级超细纤维无纺布,由SEM可观察到纤维之间有不同程度的粘结.在孔隙率约为75%左右的情况下,该无纺布的抗拉强度可达6.1 MPa,延伸率为500%.     

可生物降解聚酯酰胺的合成及其对药物缓释作用的研究

通过酰胺二元醇、1，4－丁二醇、己二酸的无规共聚得到了富含酯链段的可生物降解聚酯酰胺。以对硝基苯胺为模型药物，初步研究了不同载药量时的释药行为及分子量对药物释放的影响。     

由脂肪族二酰胺二醇合成聚酯酰胺及表征

利用脂肪族二元酸酯与乙醇胺反应容易获得的对称二酰胺二醇,经缩聚合成聚酯酰胺预聚体,并针对端羧基和端羟基同时扩链来提高分子量,获得可生物降解的聚酯酰胺.首先将N,N′-二(2-羟乙基)草酰胺(HEOA)或N,N′-二(2-羟乙基)己二酰胺(HEHA)与己二酸和丁二醇缩聚,制备同时带有端羧基及端羟基的脂肪族聚酯酰胺预聚体,通过1,4-双(2-噁唑啉)苯及己二酰双己内酰胺混合扩链剂扩链,获得高分子量脂肪族聚酯酰胺,并通过红外、1H-NMR、DSC及TGA对其结构和热性能进行了表征.结果表明,预聚体在制备过程发生了一定的酯-酰胺交换反应;扩链后聚合物的熔点、熔融焓和热稳定性有所下降;但热稳定性仍接近或略高于聚己二酸丁二酯.     

PREPARATION AND PROPERTIES OF POLY （LACTIC ACID-CO-GLYCOL TEREPHTHALIC ACID） COPOLYESTER

To obtain a kind of biodegradable polymer material with satisfactory properties, a new biodegradable copolyester poly(lactic acid-co-glycol terephthalate) (PETA), was synthesized from three monomers of lactic acid, glycol and terephthalic acid. The resulting copolyesters, PETA, were characterized by FT-IR, 1H-NMR, DSC, TGA and by the ways of weight loss rate to characterize their biodegradability. The findings in this work indicated that, the TmS and TdS of copolyesters PETA increased with increasing contents of the terephthalic acid units. From the biodegradation tests in natural soil, boiling water, acid buffer solution and alkali buffer solution, it was shown that the biodegradability of copolyesters PETA decreased with increasing contents of the terephthalic acid units.     

PREPARATION AND PROPERTIES OF POLY(LACTIC ACID-CO-GLYCOL TEREPHTHALIC ACID)COPOLYESTER

1. INTRODUCTIONThe amount of industrial and municipal waste has been increasing all over the world. Therefore, the design and development of materials capable of being degraded into safe components under specific environmental conditions have become incre…     

非晶聚对苯二甲酸乙二酯的制备与表征

通过单体酯交换法和聚 2 ,6 萘二甲酸乙二酯 (PEN)与低分子量PET酯交换的方法分别合成了一系列NPA/TPA/EG和IPA/TPA/EG共聚酯 .随着NPA或IPA单元含量的增加 ,等温结晶速度迅速降低 ,共聚物的结晶性降低甚至非晶化 .由NMR分析得知单体酯交换法与聚合物酯交换法得到的共聚酯NPA/TPA/EG序列分布相近 ,链结构都接近完全无规 .由DSC结果分析 ,随共聚单体含量的增加 ,熔点和熔融热降低 ,结晶度也随之降低 .当NPA或IPA含量达到 2 0 %时 ,可以得到非晶的共聚酯 (APET) .本文还对共聚物组成与结晶温度的关系进行了表征     

Direct synthesis of potentially biodegradable aromatic–aliphatic thermotropic copolyesters with photocrosslinking properties

ABSTRACT

In this study, aromatic–aliphatic thermotropic copolyesters derived from p-hydroxybenzoic acid, p-hydroxycinnamic acid (HCA), terephthalic acid and polyethylene glycol (PEG) with different molecular weight (200, 400, 600) were directly synthesised via Vilsmeier adduct solution polymerisation method. The structure, thermal behaviour, liquid crystal property, hydrophylicity and photoactivity were investigated by Fourier transform infrared and nuclear magnetic resonance spectroscopy, differential scanning calorimeter, polarised optical microscopy, water contact angle measurement and ultraviolet (UV) spectrophotometer. The PEG incorporation ratio is 0.540–0.691 related to the HCA units, because of its low reactivity. And, the copolyesters have relatively low melting temperatures (96–107°C) and good hydrophylicity (water contact angle value 61.2–75.3°) as compared with wholly aromatic thermotropic copolyester. All of the copolyesters exhibited nematic liquid crystal behaviour and the stable mesophase temperature range was more than 60°C after being melted. The resulted copolyesters had enough thermal stability for melt processing without any degradation. The UV absorption intensities decreased with increased irradiation time, indicating that photocrosslinking occurred.     

Property relationships in dimer acid-modified copolyesters of poly(1,4-cyclohexylene dimethylene terephthalate) and poly(1,4-cyclohexylene dimethylene 1,4-cyclohexane dicarboxylate)

Dimer acid (D) modified copolyesters based on 1,4-cyclohexane dimethanol (CHDM) and either terephthalic acid (T) or trans-1,4-cyclohexane dicarboxylic acid (C) were examined. Both series produced clear, flexible materials with physical properties changing regularly with changing modifier levels. Yield stress, elongation at break, and Young's modulus showed linear correlations of log property versus volume fraction of CHDM-D segments in accord with the logarithmic rule of mixtures. Annealing the CHDM-T-based copolyesters caused little or no change in properties. Annealing the CHDM-C-based copolyesters gave similar results except for a large decrease in the modulus—the higher the dimer acid level, the larger the decrease in modulus. The density measurements, the x-ray pattern, and the dynamic mechanical analysis at 110 Hz before and after the annealing treatment supported the hypothesis that the modulus decrease resulted from domain perfection in the copolyester induced by the annealing process. Transmission electron-microscope examination of osmium tetroxide-stained films supported this hypothesis, although initial results were not repeatable.     

Biodegradable aliphatic/aromatic copolyesters based on terephthalic acid and poly(L-lactic acid): Synthesis, characterization and hydrolytic degradation

<正>Biodegradable aliphatic/aromatic copolyesters,poly(butylene terephthalate-co-lactate)(PBTL) were prepared via direct melt polycondensation of terephthalic acid(TPA),1,4-butanediol(BDO) and poly(L-lactic acid) oligomer(OLLA). The effects of polymerization time and temperature,as well as aliphatic/aromatic moiety ratio on the physical and thermal properties were investigated.The largest molecular weight of the copolyesters was up to 64100 with molecular weight distribution index of 2.09 when the polycondensation was carried out at 230℃for 6 h.DSC,XRD,DMA and TGA analysis clearly indicated that the degree of crystallinity,glass-transition temperature,melting point,decomposition temperature, tensile strength,elongation and Young's modulus were influenced by the ratio between TPA and OLLA in the final copolyesters.Hydrolytic degradation results demonstrated that the incorporation of biodegradable lactate moieties into the aromatic polyester could efficiently improve hydrolytic degradability of the copolymer even though it still had many aromatic units in the main chains.     

PROPERTIES AND MICROSTRUCTURE OF AROMATIC LIQUID CRYSTALLINE COPOLYESTERS

The properties and structures of thermotropical liquid crystalline copolyesters basedon p-hydroxybenzoic acid (PHBA), terephthalic acid (TPA) and bisphenol A (BPA) werestudied by DSC, WAXD, hot stage polarized microscopy and NMR. It was found that mostof the copolyesters were soluble in many common organic solvents. The copolyesters hadfow T_m/T_f values and a broad range of liquid crystal phase, making the polymers readilymelt-processable. The effects of annealing at different temperatures on the copolyestercontaining 33% PHBA were also discussed. It was noted that annealing at ca. 200℃(below Tc - n) could lead to the increasing of the crystallinity of the copolyester while themicrostructure and sequence structure had not changed. Annealing at ca.280℃ (nearTc - n) could bring a change of crystal and sequence structure and simultaneously madethe ndcrodomains be ordered more perfectly.     

Synthesis and properties of novel photocrosslinkable aromatic-aliphatic liquid crystal copolyesters based on poly(ethylene glycol) and cinnamic acid

Firstly, PEGn-TA monomers with carboxyl functional groups were synthesised by terephthalic acid (TA) and poly(ethylene glycol) (PEG) with molecular weight of 200, 400 and 600. Then, photocrosslinkable thermotropic liquid crystal copolyesters derived from PEGn-TA, 4,4?-biphenol, 4-hydroxy-cinnamic acid and 4-hydroxy-benzoic acid were successfully obtained by Vilsmeier adduct solution polymerisation method. Influence of PEG molecular weight on thermal behaviour, liquid crystal mesophase, hydrophilicity, structure and photoactivity were investigated by various measurements. Experimental results indicated that all copolyesters showed nematic mesophase textures, relative low melting temperatures, and two glass transitions as well as better hydrophilicity were observed for those contained higher PEG molecular weight. Photocrosslinking rate was increased first and then decreased due to effect of flexible PEG moieties. The resulted copolyesters with liquid crystal behaviour, excellent hydrophilicity and photoactivity could be potentially used as biomaterial.     

固态后缩聚方法合成高分子量的含磷热致性液晶共聚酯

为了获得较高分子量的具有高阻燃性的热致性液晶高分子,通过固态聚合方法合成了一种基于对羟基苯甲酸、对苯二甲酸、乙二醇和含磷菲环取代二酚的高热稳定性、较低相转变温度和宽的液晶相转变温度范围的含磷液晶共聚酯(BDQTEP),并对该含磷液晶共聚酯预聚物(pre-BDQTE)在不同固态聚合条件下获得的聚合物热性能和液晶性进行了研究.对其固态反应速率控制进行了初步的探讨,当反应温度为235℃时,固态聚合反应较为理想.在聚合的初始阶段,共聚酯特性黏数[η]、黏流温度Tf和羧基浓度[COOH]均随聚合时间而明显变化,但在6 h后变化较小,几乎不变.通过固态后缩聚,将熔融聚合获得的特性黏数[η]=0.44 dL/g的含磷液晶共聚酯BDQTE的特性黏数提高了近两倍.