Ag担载对TiO2光催化活性的影响

 采用光化学沉积法合成了Ag/TiO2光催化剂,以苯酚降解反应考察了光催化剂活性随Ag担载量的变化,用TEM观察了Ag在TiO2表面的分布与形貌,以漫反射紫外-可见光谱(DRS)分析了不同Ag担载量的光催化剂的光谱特征. 结果表明,适宜担载量的Ag可显著提高TiO2的光催化活性. TEM观察显示,Ag在TiO2表面形成纳米级团簇结构,随Ag担载量的增加,团簇尺寸增大. DRS分析表明,Ag的担载对TiO2紫外区域的光谱特征没有影响. 根据Ag团簇的能级随其几何尺寸的变化分析了Ag担载量的变化对TiO2光催化活性的影响机理.     

Au/TiO2的制备及其光催化氧化丙烯的研究

采用浸渍法制备了Au/TiO2光催化剂,使用X射线能谱(XPS)和透射电子显微镜(TEM)对样品进行了表征.结果表明,Au颗粒的尺度约为4—6nm;Au4f7/2的结合能为83.3eV,与Au0的标准峰位(84.0eV)相比,向低结合能方向移动了0.7eV,使其表现出俘获电子的特性.以丙烯的光催化氧化为指标反应,对制备的Au/TiO2的活性进行了评价,结果显示,Au/TiO2的光催化活性明显高于单一TiO2的,且当Au的担载量在0.1—5.0%范围内变化时,催化活性随着担载量的增加而显著增加.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶-凝胶法将TiO2担载在介孔MCM-41分子筛上, 制备了不同TiO2含量的系列TiO2/MCM-41复合材料, 利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征. TiO2的晶型为锐钛矿相, 复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小, TiO2的平均粒径随其担载量的增加而增大. 以罗丹明B的光催化降解为探针反应, 评价了TiO2/MCM-41复合材料的光催化降解活性. 结果表明, 在紫外光照射下, 罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学, 复合材料对罗丹明B的光催化降解活性明显高于商用TiO2 (P-25), 复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶.凝胶法将TiO2担载在介孔MCM-41分子筛上,制备了不同TiO2含量的系列TiO2/MCM-41复合材料,利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征.TiO2的晶型为锐钛矿相,复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小,TiO2的平均粒径随其担载量的增加而增大.以罗丹明B的光催化降解为探针反应,评价了TiO2/MCM-41复合材料的光催化降解活性.结果表明,在紫外光照射下,罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学,复合材料对罗丹明B的光催化降解活性明显高于商用TiO2(P-25),复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

水洗处理对Au/TiO2催化剂光催化活性的影响

以Au(S2O3)3-2为金前驱体, 分别采用水洗(W)和旋蒸(E)工艺制备了Au/TiO2催化剂. 用UV-Vis漫反射光谱(DRS)、X 射线衍射(XRD)、透射电子显微镜(TEM)和原子吸收光谱(AAS)对制备的催化剂样品进行了表征, 通过光催化降解甲基橙对催化剂光催化活性进行了评价. 结果表明, 通过水洗处理, 催化剂样品表面形成了具有较好分散性的金纳米粒子(2-5 nm), 而旋蒸工艺制备的样品表面形成一层金的包覆结构. Au/TiO2催化剂的光催化活性与制备工艺密切相关. 在相似的金负载量下, 水洗法制备的样品比旋蒸法制备的样品具有更高的光催化活性.     

TiO2晶型对Au/TiO2上光催化分解臭氧的影响

以不同晶型TiO2为载体,采用沉积-沉淀法制备了Au/TiO2光催化剂,并用紫外-可见漫反射光谱、X射线光电子能谱(XPS)和表面光电压谱(SPS)等手段进行了催化剂表征,详细考察了Ti O2晶型对Au/TiO2光催化分解臭氧活性的影响.结果表明,光催化分解臭氧的活性顺序为Au/P25>Au/Anatase>Au/Rutile,这与不同的单一Ti O2对光催化臭氧分解的活性顺序是一致的.但在TiO2上沉积金后,其对光催化臭氧的分解活性有了显著的提高.由催化剂的Au4fXPS分析发现,不同晶型Ti O2上的电荷向金簇迁移的能力有明显差异,加之载体本身对光催化臭氧分解活性不同,两者协同作用导致负载金催化剂光催化分解臭氧活性的不同.SPS信号强度与催化剂光催化活性有很好的对应关系,SPS信号越强,光生电子和空穴分离效率越高,光催化活性越好.     

Au掺杂方式对锐钛矿TiO2光催化性能的影响

结合超临界乙醇干燥技术, 采用沉积-沉淀(DP)和共沉淀(CP)法分别制备了具有单一锐钛矿晶相的Au/TiO2和Au(0.2%, 原子分数)-TiO2光催化剂, 通过XRD、BET、TEM、XPS和Raman手段表征样品中Au的掺杂形态, 以光催化降解甲基橙为模型反应考察了样品的光催化活性. 结果表明, DP法制备的Au/TiO2在110 ℃干燥处理后, 表面存在的Au3+能有效地促进锐钛矿TiO2光催化性能, 其一级反应速率常数比纯锐钛矿TiO2提高了3.2倍, 比商用光催化剂Degussa-P25提高了4.1倍, 而当Au3+被还原为Au0后光催化活性下降. 用CP法制备的Au-TiO2并没有较大地提高锐钛矿TiO2光催化性能, 在焙烧温度达到800 ℃时, Au向表面迁移聚集, 造成锐钛矿TiO2晶格氧空位和缺陷位增加, 使光催化活性下降.     

纳米TiO2光催化剂的酸催化水解合成与表征

以TiCl4为钛源,采用酸催化水解法控制TiCl4水解速度,合成了纳米TiO2光催化剂。以苯酚的光催化降解为模型反应,考察了酸催化剂种类、水解温度、煅烧温度对TiO2光催化活性的影响。采用X射线衍射(XRD)、紫外-可见漫反射(DRS)、扫描电镜(SEM)、低温氮物理吸附,分析了TiO2光催化剂的晶相结构、光谱特征以及表面形貌。结果表明,以HCl为催化剂、水解温度98℃、煅烧温度500℃下制得TiO2活性最高。最佳条件下合成的TiO2前驱体为无定型结构,400℃煅烧时几乎完全转化为锐钛矿相,800℃时完全转化为金红石相。随着煅烧温度升高,TiO2光吸收阈值红移,TiO2粒子尺寸增大,比表面积下降,光催化活性降低。     

Eu~(3 )、Si~(4 )共掺杂TiO_2光催化剂的协同效应

采用溶胶-凝胶-浸渍法制备了Eu/Ti/Si纳米光催化剂,并通过XRD、FT-IR、EPR等进行了表征.结果表明,掺入Eu3 和Si4 ,阻止了TiO2从锐钛矿晶型向金红石晶型的转变,使TiO2的粒径减小,且Eu3 能够促进Si4 进入TiO2的晶格中.以甲基橙为光催化反应模型化合物,考察了光催化剂的活性.测定了甲基橙在不同光催化剂上的吸附常数,探讨了催化剂对甲基橙的吸附机理.Eu3 和Si4 的最佳掺入量分别为wEu=0.03%、wSiO2=39.06%,且Eu3 和Si4 同时掺入TiO2光催化剂产生协同效应.讨论了光催化活性与催化剂性质的关系.     

Eu3＋、Si4＋共掺杂TiO2光催化剂的协同效应

采用溶胶-凝胶-浸渍法制备了Eu/Ti/Si纳米光催化剂, 并通过XRD、FT-IR、EPR等进行了表征.结果表明,掺入Eu3＋和Si4＋, 阻止了TiO2从锐钛矿晶型向金红石晶型的转变, 使TiO2的粒径减小, 且Eu3＋能够促进Si4＋进入TiO2的晶格中.以甲基橙为光催化反应模型化合物, 考察了光催化剂的活性.测定了甲基橙在不同光催化剂上的吸附常数,探讨了催化剂对甲基橙的吸附机理. Eu3＋和Si4＋的最佳掺入量分别为wEu=0.03％、wSiO2=39.06％,且Eu3＋和Si4＋同时掺入TiO2光催化剂产生协同效应.讨论了光催化活性与催化剂性质的关系.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.