MgFe0.1Al1.9O4 的合成及其催化乙苯与 CO2 的氧化脱氢反应

 以柠檬酸为络合剂, 采用溶胶-凝胶法制备了具有尖晶石结构的 MgFe_0.1Al_1.9O₄ 催化剂, 并将其用于催化乙苯与 CO₂ 氧化脱氢反应. 运用 X 射线衍射、X 射线能量色散光谱分析、红外光谱、热重-差热、N₂ 吸附-脱附和 H₂ 程序升温还原等技术对催化剂进行了表征. 结果表明, 在 650 ºC 以上焙烧即可制得结构确定、组成均一的 Mg-Fe-Al-O 复合氧化物催化剂, 其中 Fe 物种主要以同晶取代的形式存在于尖晶石骨架中. 随着焙烧温度的升高, 尖晶石结晶度提高, Fe 物种还原能力下降, 催化剂晶粒度增大, 比表面积降低. 700 ºC 焙烧制备的 MgFe_0.1Al_1.9O₄ 具有较好的催化乙苯与 CO₂ 氧化脱氢反应活性和稳定性.     

Ce助剂对V/SiO_2催化CO_2氧化乙苯脱氢性能的影响

通过N2吸附、X射线衍射(XRD)、X射线光电子能谱(XPS)、H2程序升温还原(H2-TPR)、CO2程序升温脱附(CO2-TPD)和热重分析(TGA)等多种表征手段和催化反应性能评价,研究了铈助剂的添加对V/SiO2催化CO2氧化乙苯脱氢性能的影响.结果表明,Ce助剂不仅提高了催化剂活性组分分散性和氧化还原性能,抑制了钒物种的深度还原,而且增强了催化剂碱性和CO2吸附能力,减缓了积炭生成,从而显著提高了V-Ce/SiO2对CO2氧化乙苯脱氢反应的催化活性和稳定性.在本实验中,V(0.8)-Ce(0.25)/SiO2催化剂表现出最佳的催化性能,苯乙烯(ST)收率可达55.6%,选择性为98.5%,反应12 h后,催化剂活性基本不变,与惰性N2气氛比较,CO2明显促进了乙苯脱氢反应,归因于CO2能保持催化剂表面钒物种的高价态.     

FeMn、FeMnNa和FeMnK催化剂上合成气制低碳烯烃的比较

研究了钠、钾助剂对FeMn 合成低碳烯烃催化剂结构及性能的影响. 低温N₂吸附、X射线光电子能谱（XPS）、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、CO/CO₂程序升温脱附（CO/CO₂-TPD）、Mössbauer 谱和CO+H₂反应的研究结果表明,增加Mn助剂含量促进了活性相的分散和低碳烯烃的生成,而过多锰助剂在催化剂表面的富集则降低了费托合成反应的CO转化率;钾助剂和钠助剂的加入均抑制了催化剂的还原并且促进了CO₂和CO的吸附. 比较还原后（H₂/CO摩尔比为20）和反应后（H₂/CO摩尔比为3.5）催化剂的体相结构可以发现,在FeMn、FeMnNa和FeMnK催化剂中,由于钾助剂的碱性和CO吸附能力较强,因此体相中FeC_x的含量相对较高;而活性测试结果表明,FeMnNa催化剂拥有最好的CO转化率（96.2%）和低碳烯烃选择性（30.5%,摩尔分数）.     

钒氧化物催化CO2氧化异丁烷脱氢的研究

采用溶胶-凝胶法制备了一系列钒氧化物催化剂,并用于CO₂氧化异丁烷脱氢反应. 采用X射线衍射、低温N₂吸附-脱附、O₂程序升温氧化、程序升温表面反应和原位傅里叶变换红外光谱等方法研究了催化剂的性质. 反应结果表明,尽管所有钒氧化物催化剂的丁烯选择性都大于85%,但随着催化剂组成和制备方法的改变,催化活性和稳定性差异显著. 其中,12 wt% V₂O₅/Ce_0.6Zr_0.4O₂（7 wt%）-Al₂O₃的催化活性最高,而6 wt% V₂O₅-Ce_0.6Zr_0.4O₂（7 wt%）-Al₂O₃的稳定性最佳. 关联分析催化反应结果与催化剂表征表明,钒氧化物的催化活性取决于VO_x物种的结晶度和分散度,而催化剂表面所积重质焦炭的特性是决定催化剂稳定性的关键. 非稳态反应和原位光谱结果确认,CO₂氧化异丁烷脱氢遵循Mars-van Krevelen氧化还原机理.     

Au/α-Fe2O3 催化剂存贮失活环境因素及机理分析

 采用沉积沉淀法制备了 CO 低温氧化催化剂 Au/α-Fe₂O₃, 通过 X 射线衍射、X 射线光电子能谱、N₂ 吸附-脱附、傅里叶变换红外光谱、H₂ 程序升温还原和 CO₂ 程序升温脱附等手段对催化剂进行了表征, 探讨了在室温大气气氛下光线照射以及表面吸附等环境因素所导致的催化剂存贮失活及其作用机理. 结果表明, 经 110 ^oC 干燥的 Au/α-Fe₂O₃催化剂表面同时存在 Au³⁺和 Au^δ+ (0 ≤ δ ≤ 1) 物种, 且前者催化 CO 氧化的活性更高; 在室温大气气氛下, 紫外线照射会引起 Au³⁺的还原和 Au 颗粒的生长, 导致催化剂的不可逆失活. 此外, 空气中的 H₂O 和 CO₂ 可同时吸附在 α-Fe₂O₃的表面, 形成表面碳酸盐物种, 会引起催化剂的可逆失活.     

Ni/SiO2-ZrO2催化剂焙烧温度对其催化愈创木酚加氢脱氧性能的影响简

采用化学沉淀法合成了SiO₂-ZrO₂复合氧化物载体,并以浸渍法制备了Ni/SiO₂-ZrO₂双功能催化剂,考察了焙烧温度对催化剂结构及其催化愈创木酚加氢脱氧制环己烷性能的影响. 结果表明,经500℃焙烧催化剂的加氢脱氧活性最高,在Ni金属中心和SiO₂-ZrO₂载体材料的协同作用下,愈创木酚转化率为100%,环己烷选择性为96.8%. 对催化剂进行N₂物理吸附、H₂化学吸附、X射线衍射分析、H₂程序升温还原、NH₃程序升温脱附与Raman光谱等表征后发现,合成的SiO₂-ZrO₂为无定形的酸碱两性氧化物;经500℃焙烧的催化剂样品的有效比表面积和孔体积均明显增大,表面酸量最多,硝酸镍分解成小颗粒的NiO较易被H₂还原,这些特性是该催化剂样品具有高效加氢脱氧活性的原因.     

载体对钒铬氧化物催化剂结构及催化3-甲基吡啶氨氧化反应活性的影响

通过等体积浸渍法制备了Nb₂O₅,MgF₂,TiO₂和SiO₂负载和未负载的钒铬氧化物催化剂,并应用X射线衍射、N₂吸附-脱附、H₂程序升温还原和NH₃程序升温脱附对催化剂进行了表征. 结果表明,催化剂比表面积较大时有利于CrVO₄-I(单斜)的生成,比表面积较小则有利于CrVO₄-III(斜方)的生成. 在310-400℃下3-甲基吡啶氨氧化制备3-氰基吡啶反应中,具有较高催化活性的催化剂与V物种还原性较高和表面活性位数量较多有关; 而高的3-氰基吡啶选择性则与催化剂表面较低的酸性密切相关. 升高反应温度可大幅度提高催化剂的活性,且其选择性基本不变.     

SiO2气凝胶负载的Ni催化剂在甲烷部分氧化制合成气反应中的催化性能及稳定性

以常压有机溶剂置换(A)和溶剂置换-表面改性(B)方式制备的两种SiO₂气凝胶(SiO₂-A(或B)型气凝胶,记为SiO₂-A(or B)G)为载体, 采用常规浸渍法和聚乙烯吡咯烷酮(PVP)添加浸渍法合成不同SiO₂气凝胶负载的Ni/SiO₂催化剂, 并考察其催化的甲烷部分氧化(POM)制合成气的反应性能. 结果表明, 各催化剂的初始反应性能相近, 但Ni/SiO₂-BG的POM稳定性明显较Ni/SiO₂-AG的差, 而PVP添加制备的催化剂稳定性则获明显改善, Ni/SiO₂-AG-PVP、Ni/SiO₂-BG-PVP上POM稳定性相近. 结合X射线衍射(XRD)、程序升温还原反应(H₂-TPR)、高分辨透射电镜(TEM)和Brunauer-Emmett-Teller (BET)等表征结果的分析发现: (1) SiO₂-AG表面上存在一定量的羟基, 可促进亲水性金属物种与其的相互作用, 而SiO₂-BG表面上基本为有机基团, 与亲水性金属物种几乎无作用; (2) PVP的存在可使金属物种进入亲/疏水载体孔道深处, 抑制焙烧中载体骨架的收缩和金属颗粒的生长, 进而促进金属-载体的相互作用. 这二者均能有效地提高催化剂的POM反应稳定性.     

表面助剂改性对Cu/ZnO/Al2O3甲醇合成催化剂性能的影响

采用共沉淀-后浸渍方法制备了表面助剂改性的Cu/ZnO/Al₂O₃ (CZA)甲醇合成催化剂, 在固定床反应器上以合成气为原料分别考察了三种助剂(Zr、Ba和Mn)对CZA催化剂性能的影响; 以Zr为助剂时反应温度的影响; 并进行了催化稳定性试验. 利用粉末X射线衍射(XRD)、低温氮气吸脱附(N₂-sorption)、氧化亚氮(N₂O)反应吸附技术、X射线光电子能谱(XPS)、氢气程序升温吸脱附(H₂-TPD)、扫描电子显微镜(SEM)和高分辨透射电子显微镜(HR-TEM)技术对催化剂进行了表征.结果显示: 以Zr或Ba作为助剂能够明显提高CZA催化剂耐热前后的甲醇时空收率(STY); Mn的引入降低了CZA催化剂的耐热前活性; Zr的引入降低了CZA催化剂最高活性温度点, 增强了CZA催化剂的催化稳定性; 还原态CZA催化剂表面Cu⁰和ZnO都能吸附活化氢气, Cu⁰与ZnO的强相互作用有利于提高催化剂的性能, 耐热后催化剂性能的降低归因于Cu晶粒的长大. 在实验和表征结果基础上,提出了CZA催化剂上合成气制甲醇的“双向同步催化反应历程”.     

Cs取代对Ni-H3PW12O40/SiO2催化剂结构性质和催化性能的影响

采用两步浸渍法和载体上的原位反应制备了一系列Cs部分取代的Ni-Cs_xH_3-xPW₁₂O₄₀/SiO₂催化剂,并用N₂吸附比表面积测定(BET)、电感耦合等离子体发射光谱(ICP)、X射线衍射(XRD)、拉曼光谱(Raman)、原位X射线衍射(in situ XRD)、NH₃程序升温脱附(NH₃-TPD)、H₂程序升温还原(H₂-TPR)、H₂程序升温脱附(H₂-TPD)、吡啶吸附傅里叶变换红外(FTIR)光谱等分析测试技术对催化剂进行了表征. 以正癸烷为模型化合物,对催化剂的加氢裂化性能进行了评价. 结果表明,8%Ni-50%Cs_1.5H_1.5PW/SiO₂催化剂具有最高的C₅₊收率,明显优于8%Ni-50%H₃PW/SiO₂催化剂和工业催化剂. 随着Cs 在Cs_xH_3-xPW中比例的增加,正癸烷的转化率逐渐降低,而C₅₊选择性则逐渐提高. 当催化剂具有合适的孔径时,选择性的提高是由于催化剂酸性的减弱,而转化率的降低则是由于催化剂加氢能力的减弱.     

Oxidative dehydrogenation of ethylbenzene to styrene with CO2 over Al-MCM-41-supported vanadia catalysts

Catalytic performance of Al-MCM-41-supported vanadia catalysts (V/Al-MCM-41) with different V loading was investigated for oxidative dehydrogenation of ethylbenzene to styrene (ST) with CO₂ (CO₂-ODEB). For comparison, pure silica MCM-41 was also used as support for vanadia catalyst. The catalysts were characterized by N₂ adsorption, X-ray diffraction (XRD) pyridine-Fourier-transform infrared spectroscopy, H₂-temperature-programmed reduction, thermogravimetric analysis (TGA), UV-Raman, and diffuse reflectance (DR) UV–vis spectroscopy. The results indicate that the catalytic behavior and the nature of V species depend strongly on the V loading and the support properties. Compared with the MCM-41-supported catalyst, the Al-MCM-41-supported vanadia catalyst exhibits much higher catalytic activity and stability along with a high ST selectivity (>98%). The superior catalytic performance of the present V/Al-MCM-41 catalyst can be attributed to the Al-MCM-41 support being more favorable for the high dispersion of V species and the stabilization of active V⁵⁺ species. Together with the characterization results of XRD, TGA, and DR UV–Vis spectroscopy, the deep reduction of V⁵⁺ into V³⁺ during CO₂-ODEB is the main reason for the deactivation of the supported vanadia catalyst, while the coke deposition has a less important impact on the catalyst stability.     

Nd,Ce和La改性对Ni/SBA-15催化剂在CH4/CO2重整反应中性能的影响

以稀土金属Nd,Ce或La的氧化物为助剂,采用β-环糊精浸渍法对Ni/SBA-15催化剂进行了改性,并运用X射线衍射、N₂吸附-脱附、程序升温还原和热重等手段考察了改性的催化剂在CO₂重整CH₄制合成气反应中的催化性能. 结果表明,Nd等稀土金属氧化物的添加对催化剂孔结构和晶相结构等性质影响不大,但可影响NiO的还原; Nd的添加使NiO与载体之间以Ni-Nd-O形式相互作用,促进了活性组分NiO的还原. 其中,Nd的添加量为5-10 wt%时所制备的催化剂在重整反应中的催化活性最高,且具有很强的抗积碳性能. La和Ce氧化物促进的Ni催化剂也表现出类似的性质和催化性能.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Catalytic performance of silica-supported chromium oxide catalysts in ethane dehydrogenation with carbon dioxide

The oxidative dehydrogenation of ethane into ethylene by CO₂ over a series of silica-supported chromium oxide catalysts was investigated. The results showed that the catalysts were effective for the reaction and CO₂ in the feed promoted the catalytic activity. The 5%Cr/SiO₂ catalyst exhibited the excellent performance with 30.7% ethane conversion and 96.5% ethylene selectivity at 700^oC. ESR and UV-DRS were used to probe the active sites and the species with high valent states (Cr⁵⁺ and/or Cr⁶⁺) were found to be important for the reaction.     

助剂对NiMgAl催化剂的结构和甲烷二氧化碳重整反应性能的影响(英文)

向担载镍基催化剂NiMgAl中添加助剂(Co,Ir或Pt)制备了三种助剂促进型催化剂,通过氢气程序升温还原(H2-TPR),CO2/CH4程序升温表面反应(CO2/CH4-TPSR)和CO2程序升温脱附(CO2-TPD)等方法对催化剂进行表征.助剂对催化剂性能的影响通过甲烷干重整实验进行评价.添加少量的Pt或Ir助剂可以降低Ni活性组分的还原温度和提高反应性能.添加助剂的样品与原始NiMgAl催化剂相比能够降低反应的活化能,添加Co或Ir助剂的催化剂与NiMgAl催化剂相比活化能有了明显的降低.NiMgAl催化剂的活化能为51.8 kJ·mol-1,添加Pt助剂的NiPtMgAl催化剂活化能降至26.4 kJ·mol-1.NiMgAl催化剂中添加Pt助剂制备的催化剂具有较好的催化活性和较低的活化能.CH4-TPSR和CO2-TPSR结果表明添加Pt助剂可以在更低的温度下(与NiMgAl催化剂相比)提高CH4的活化能力,并在催化剂表面形成更多的碳物种.CO2-TPD结果显示,添加助剂的催化剂与NiMgAl样品相比在反应温度区间内增加了CO2的吸附/脱附量.     

Ni/CeO2-SiO2催化剂的制备、表征及其甲烷部分氧化制合成气性能

以硝酸亚铈（Ce（NO₃）₃·6H₂O）和正硅酸四乙酯（C₈H₂₀O₄Si）为前驱体,采用溶胶-凝胶法合成了系列具有大比表面积的xCeO₂-（1-x）SiO₂（x = 0,0.25,0.50,0.75,1）复合氧化物载体,然后浸渍活性组分Ni制得用于甲烷部分氧化制合成气的Ni催化剂。运用N₂物理吸附-脱附、X射线粉末衍射、扫描电镜、紫外-可见漫反射光谱、氢程序升温还原、氨程序升温脱附和热重等手段对所得催化剂的组织结构、还原性、表面酸性和积炭行为等进行了表征;同时考察了催化剂的组成、焙烧温度和反应时间等对催化剂在甲烷部分氧化制合成气中催化性能的影响。表征结果表明,该系列Ni/CeO₂-SiO₂催化剂具有大比表面积,CeO₂晶粒较小,NiO的分散性好且易被还原,表面酸性弱,不容易积炭。当Ce/Si摩尔比为1：1,活性组分Ni的质量分数为10%,焙烧温度为700℃时,所制备的Ni/CeO₂-SiO₂催化剂表现出较好的稳定性、最高的CH₄转化率（~84%）和对产物CO及H₂的选择性（>87%）。     

An Overview on the Dehydrogenation of Alkylbenzenes with Carbon Dioxide over Supported Vanadium–Antimony Oxide Catalysts

Utilization of carbon dioxide as a soft oxidant for the catalytic dehydrogenation of ethylbenzene (CO₂-EBDH) has been recently attempted to explore a new technology for producing styrene selectively. This article summarizes the results of our recent attempts to develop effective catalyst systems for the CO₂-EBDH on the basis of alumina-supported vanadium oxide catalysts. Its initial activity and on-stream stability were essentially improved by the introduction of antimony oxide as a promoter into the alumina-supported catalyst. Insertion of zirconium oxide into alumina support substantially increased the catalytic activity. Modification of alumina with magnesium oxide yielded an increase of catalyst stability of alumina-supported V–Sb oxide due to the coking suppression. Carbon dioxide has been confirmed to play a beneficial role of selective oxidant in improving the catalytic performance through the oxidative pathway, avoiding excessive reduction and maintaining desirable oxidation state of vanadium ion (V⁵⁺). The positive effect of carbon dioxide in dehydrogenation reactions of several alkylbenzenes such as 4-diethylbenzene, 4-ethyltoluene, and iso- and n-propylbenzenes was also observed. Along with the easier redox cycle between fully oxidized and partially reduced vanadium species, the optimal surface acidity of the catalyst is also responsible for achieving high activity and catalyst stability. It is highlighted that supra-equilibrium EBDH conversions were obtained over alumina-supported V–Sb oxide catalyst in CO₂-EBDH as compared with those in steam-EBDH in the absence of carbon dioxide.     

V2O5/赤铁矿催化剂结构及其NH3选择性催化还原NOx性能

以水热合成针铁矿为前驱体浸渍偏钒酸铵,分别于300,400和500℃空气中焙烧,制备了不同活性组分负载量的V₂O₅/赤铁矿（V/H）催化剂,用于氨选择性催化还原（SCR）脱硝。采用X射线衍射、透射电子显微镜、比表面积分析仪、程序升温还原及程序升温脱附等方法对催化剂结构进行了表征,并用标气配制模拟烟气进行了脱硝实验。结果表明,300℃煅烧3%V/H催化剂当烟气温度为250-300℃时NO转化率均可达95%以上;当配气中单独加入水蒸气或低浓度SO₂（0.01%）时,V/H催化脱硝的活性不受影响;当系统加入高浓度的SO₂（0.03%与0.05%）或同时添加H₂O与SO₂时,SCR脱硝效率下降,其机制可能是SO₂在催化剂表面竞争吸附所致,停止添加后,催化活性迅速恢复。     

Study of oxidative dehydrogenation of ethylbenzene with CO2 on supported CeO2-Fe2O3 binary oxides

Nano-sheets Al₂O₃ supported CeO₂-Fe₂O₃ binary oxides were prepared by the vacuum impregnation method. The structural and textural properties were characterized by pertinent techniques, and the materials were evaluated as catalysts for the oxidative dehydrogenation of ethylbenzene with carbon dioxide (CO₂-ODEB). The characterization results show that all samples maintain the hierarchical structure, and CeO₂-like and Fe₂O₃-like solid solutions were formed when changing the Ce-to-Fe molar ratio. The catalytic performances indicate that CeO₂-Fe₂O₃ binary oxides were effective for CO₂-ODEB, and the activity is determined by mobile oxygen, which can facilitate the dehydrogenation process. The DFT studies further identified the reaction pathway and rate-determining step. The inter-transmission of oxygen species and the presence of CO₂ refill the oxygen vacancies and restore the redox cycle of CeO₂-Fe₂O₃ binary oxides.     

Dehydrogenation of Ethylbenzene to Styrene with Carbon Dioxide Over ZrO<Subscript>2</Subscript>-based Composite Oxide Catalysts

We have been exploring various new catalyst systems for the utilization of carbon dioxide as a soft oxidant in the catalytic dehydrogenation of ethylbenzene (EB) to styrene. The utilization of CO₂ as a soft oxidant for the commercially important catalytic dehydrogenation of EB to styrene has received enormous attention recently due to its several attractive features. This review summarizes the results of our most recent findings on zirconia-based composite oxide catalyst systems exploited for this reaction. Under this systematic and comprehensive investigation various zirconia-based composite oxide catalysts namely, TiO₂-ZrO₂, MnO₂-ZrO₂, CeO₂-ZrO₂, K₂O/TiO₂-ZrO₂, B₂O₃/TiO₂-ZrO₂ and CeO₂-ZrO₂/SBA-15 have been synthesized, characterized by various techniques and evaluated for the title reaction. Most of these composite oxide catalysts were found to exhibit very interesting physicochemical characteristics and exceptionally better catalytic properties for this reaction. As revealed by characterization results, a large number of acid–base sites with moderate strength are essential for a high conversion and product selectivity of this reaction with CO₂ as the soft oxidant.