Au core-PtAu alloy shell nanowires for formic acid electrolysis

Inefficient electrocatalysts and high-power consumption are two thorny problems for electrochemical hydrogen(H2)production from acidic water electrolysis.Herein we report the one-pot precise synthesis of ultrafine Au core-Pt Au alloy shell nanowires(Au@PtxAu UFNWs).Among them,Au@Pt_0.077 Au UFNWs exhibit the best performance for formic acid oxidation reaction(FAOR)and hydrogen evolution reaction(HER),which only require applied potentials of 0.29 V and-22.6 m V to achieve a current density of 10 m A cm^-2,respectively.The corresponding formic acid electrolyzer realizes the electrochemical H2 production at a voltage of only 0.51 V with 10 m A cm^-2 current density.Density functional theory(DFT)calculations reveal that the Au-riched Pt Au alloy structure can facilitates the direct oxidation pathway of FAOR and consequently elevates the FAOR activity of Au@Pt_0.077 Au UFNWs.This work provides meaningful insights into the electrochemical H₂ production from both the construction of advanced bifunctional electrocatalysts and the replacement of OER.     

Layered Ag-graphene films synthesized by Gamma ray irradiation for stable lithium metal anodes in carbonate-based electrolytes

Lithium metal batteries are considered as high energy density battery systems with very promising prospects and have bee n widely studied.However,The uncon trollable plating/strippi ng behavior,infinite volume change and den drites formation of lithium metal anode restrict the applicati on.The unc on trolled n ucleati on of lithium caused by the non uniform multi-physical field distributions,can lead to the undesirable lithium deposition.Herein,a graphene composite uniformly loaded with Ag nano-particles(Ag NPs)is prepared through a facile Gamma ray irradiation method and assembled into self-supported film with layered structure(Ag-rGO film).Whe n such film is used as a lithium metal an ode host,the uncontrolled deposition is converted into a highly nucleation-induced process.On one hand,the Ag NPs distributed between the in terlayers of graphe ne can preferentially induce lithium nu cleati on and en able uniform deposition morphology of lithium between interlayers.On the other hand,the stable layered graphene structure can accommodate volume change,stabilize the interface between anode and electrolyte and inhibit dendrites formation.Therefore,the layered Ag-rGO film as anode host can reach a high Coulombic efficiency over 93.3% for 200 cycle(786 h)at a current density of 1 mA cm^-2 for 2 mAh cm^-2 in carbonate-based electrolyte.This work proposes a facile Gamma ray irradiation method to prepare metal/3D-skeleton structure as lithium anode host and demonstrates the potential to regulate the lithium metal deposition behaviors via manipulating the distribution of lithiophilic metal(e.g.Ag)in 3D frameworks.This may offer a practicable thinking for the subsequent design of the lithium metal anode.     

中国纤维素乙醇技术的研究进展

中国面临着严重的能源短缺和环境污染问题,中国政府正在局部几个省份内政策性鼓励燃料乙醇生产和使用.尽管当前主要是用玉米和谷物作为生产乙醇的原料,然而中国具有大量潜在的低成本的纤维素生物质原料,可以极大地扩大乙醇的产量,降低原料成本.近20年来,由于技术的革命性进步,已使得纤维素乙醇的生产成本从4美元/加仑以上,降低至约1.2-1.5美元/加仑.其中,每吨生物质约44美元.因此,目前乙醇掺汽油具有十分强的市场竞争力.已有几个公司正在建造首批商业纤维素乙醇工厂,虽然这些刚起步的小型设施在合理利用和管理上风险较小,但规模经济需要较大型工厂.尽管配送生物质原料的成本会随需求的增加而增加,但在乙醇生产基础上的生物精炼技术的发展,尤其是化工产品和动力的协同生产,将会使全过程的经济可行性大大提高.进一步深入的基础研究,将解决低成本下实现纤维素的完全利用,以确保在无政策性补贴的前提下,真正使纤维素乙醇成为具有市场竞争力的低成本纯液体燃料.     

Binary ligand strategy toward interweaved encapsulation-nanotubes structured electrocatalyst for proton exchange membrane fuel cell

Hierarchically porous architecture of ir on-nitroge n-carb on(Fe-N-C)for oxyge n reducti on reaction(ORR)is highly desired towards efficient mass transfer in the fuel cell device manner.Herein,we reported a binary ligand strategy to prepare zeolitic imidazolate frameworks(ZIFs)-derived precursors,wherein the addition of secondary ligand endows precursors with the capabilities to transform into porously interweaved encapsulation-nanotubes structured composites after calcination.The optimal catalyst,i.e.,termed as Fe₆-M/C-3,exhibits excellent durability with 88.8%current retention after 50,000 seconds in 0.1 M HClO₄solution by virtue of nanoparticles-encapsulation features,which is more positive than the benchmark commercial 20 wt%Pt/C catalyst.Moreover,a promising maximum power density of Fe₆-M/C-3 as cathode catalyst was also dem on strated in proton exchange membrane fuel cells(PEMFCs)measurements.Therefore,this binary ligand approach to the fabrication of hierarchically porous structures would also have significant implications for various other electrochemical reactions.     

Molten salt as ultrastrong polar solvent enables the most straightforward pyrolysis towards highly efficient and stable single-atom electrocatalyst

Currently,pyrolysis as the most widely used method still has some key issues not well resolved for synthesis of carbon-supported single-atom catalysts(C-SACs),e.g.,the sintering of metal atoms at high temperature as well as the high cost and complicated preparations of precursors.In this report,molten salts are demonstrated to be marvellous medium for preparation of C-SACs by pyrolysis of small molecular precursors(ionic liquid).The ultrastrong polarity on one hand establishes robust interaction with precursor and enables better carbonization,resulting in largely enhanced yield.On the other hand,the aggregation of metal atoms is effectively refrained while no nanoparticle or cluster is formed.By this strategy,a C-SAC with atomically dispersed Fe-N₄ sites and a high specific area over 2000 m² g^-1 is obtained,which illustrates high ORR activity in both acid and alkaline media.Moreover,this SAC exhibits superior methanol tolerance and stability after acid soaking at 85℃ for 48 h.It is believed that the molten-salts-assisted pyrolysis can be developed into a routine strategy as it not only can largely simply the synthesis of C-SACs,but also can be extended to prepare other types of SACs.     

镧对Mg-Si合金中Mg2Si相变质的影响

研究了Mg-5Si合金中La的添加对初生Mg2Si相变质的影响。结果表明,适量的La能够有效地变质初生Mg2Si相。基于本文的研究,在添加约0.5%La时,获得了最佳的变质效果,此时,初生Mg2Si相的尺寸减小到25μm以下,其形态从粗大的树枝形状变为多面体形状。然而,当La增加到0.8%或者更高时,初生Mg2Si相又生长为粗大的树枝形态。而且,在凝固过程中发现形成了一些LaSi2化合物,这些化合物的数量随着La的增加而呈现逐渐增加的趋势。     

电感耦合等离子体质谱法测定天然水体中19种元素

建立STD/KED模式-电感耦合等离子体质谱（ICP-MS）法同时测定天然水体中铍、硼、钛、钒、铬、锰、钴、镍、铜、锌、钼、镉、锑、钡、铊、铅、铁、砷和硒19种元素的分析方法。仪器调谐校准后,样品在线加入锂、钪、铑、铋校准溶液校正,以标准曲线内标法定量分析。标准曲线相关系数均大于0.999,样品加标回收率为92.6%～103.6%,质控样品测定值相对标准偏差为0.20%～2.6%(n=6),方法检出限为0.01～0.70μg/L。该方法灵敏度高,操作简便,节省人力,能满足天然水体中19种元素的同时检测需要。     

电解质-非电解质混合溶液活度系数的关联及溶解的推算 II:NH3-NaCl-Na2SO4-H2O体系的液固平衡热力学

由于在研究的体系中, Na2SO4是非对称电解质, 且能生成水合盐, 故推导了由非对称型电解质与非电解质所构成的混合溶液的各组分的活度系数关联通式, 并在此基础上讨论了水合盐液固平衡的计算方法.     

黄花棘豆化学成分的研究II:两种三萜皂苷的结构

从黄花棘豆的总皂苷中分离出两个新皂苷1和2.经光谱分析及化学方法确证,1为3-O-[α-L-鼠李吡喃糖基(1→2)-β-D-葡萄吡喃糖基(1→4)-β-D-葡萄吡喃糖醛酸基]-黄豆醇B;2为3-O-[α-L-鼠李吡喃糖基(1→2)-α-L-阿拉伯吡喃糖基(1→4)-β-D-葡萄吡喃糖醛酸基]-黄豆醇B.     

二氧化钛纳米管的研究进展

二氧化钛纳米管由于其新奇的光电、催化、气敏等性能引起了广泛的关注,在太阳能电池、光催化、环境净化、气体传感器等领域有潜在的应用价值.本文概述了近年来在制备方法、反应机理和组成、晶型和形貌及掺杂和应用方面的进展,并讨论了今后可能的研究发展方向.     

C60离子束撞击固体表面的坍塌与沉积(II)扫描隧道显微研究

Mass-selected C60 beam produced by laser ablation was accelerated and bombarded the (0001) surface of highly oriented pyrolitic graphite and (111) surface of gold single crystal. The samples were characterized by STM. The STM images showed that, the deposited species collapsed and formed planar structure on the solid surface, but the collapsed species were not dissociated and well oriented on the surface. Both positive and negative C60 ions were observed in the desorption mass spectra, confirming that the species collapsed on the solid surface are still the C60 clusters.     

C_(60)离子束撞击固体表面的坍塌沉积(Ⅰ)共焦显微拉曼光谱研究

为了研究C60的结构特性，我们最近在实验中将加这后的C60离子束沉积在固体表面，对其沉积后的形态进行了共焦显微拉曼光谱的表征．在记录的光谱中已检测不出C60原有的特征谱问，说明C60离子在高速憧击固体表面后，已经完全失去了原有的球状构型．C60的t）［R实验在自制的串级飞     

He+C60↔(He@C60)的反应势垒研究

The reaction barriers of (He+C60(He＠60)) have been calculated by the quantum-chemical method EHMO/ASED in the following four paths: (1) penetrate through the pentagon on the C60 cage; (2) penetrate through the hexagon on the C60 cage,(3) penetrate through the short bond; (4) penetrate through the long bond. Corresponding to each path, there are two choices: (a) while He penetrate C60 cage, the distances of the C’s which are the most adjacent to He are changed with a planar extension and a concerned window is formed; (b) while He penetrate C60 cage, the distances of the C’s which are the most adjacent to He are changed with a spherical extension and a concerned window is formed. The results are given in Figs. 1-2 and Tables 1-2. It is shown that the reaction through path(4) with choice (a) has the least reaction barrier, being optimum. At that case, a window of 9-membered ring is formed. Because the window extension of C6H6 is more free than that of C60, the barrier of He penetrating through C6H6 will be lower than that of He penetrating through C60.     

内嵌复合物X@C60中相互作用的变化规律与键本质

系统地研究了内嵌复合物Ｘ＠Ｃ６０（Ｘ＝第ＩＡ簇或第ＶＩＩＡ族元素）形成过程的能量变化,以及其中笼环境下Ｘ与Ｃ６０间相互作用的变化特征与键本质。结果表明：（１）Ｃ６０笼环境力场具有球对称性;（２）各种分解与总相互作用与内嵌原子的原子序数或原子半径呈现出规则的递变规律;（３）除Ｉ外,其余元素原子与Ｃ６０间的作用对各自复合物的稳定性都有正效应的较大贡献;（４）Ｘ在Ｃ６０笼环境中居心或偏心的稳定位置是各种     

CuxC60薄膜紫外-可见吸收光谱研究

近来,有关C60的研究主要集中在有关晶格动力学、电子结构和MxC60（M代表碱金属或碱土金属）的超导电性研究。但由于MxC60在大气中不能稳定存在,制约了MxC60的深入研究和实际应用。最近,Masterov等人报导了他们对Cu/C60的超导特性研究,认为其转变温度Tc在80－120K之间,这个转变温度比现有的MxC60的转变温度Tc-40K）要高得多,但有关更进一步的研究未见报导,因此,我们拟对CuxC60体系作较为详尽的研究,这对于进一步研究其超导机理是有必要的,本工作是在成功地制备了CuxC60薄膜的基础上,对其紫外－可见吸收光谱进行了初步的研究。定性地分析了CuxC60薄膜的电子结构,利用XPS谱分析了CuxC60薄膜中Cu的化学价态。     

二氟二草酸硼酸锂对LiFePO4/石墨电池高温性能的影响

研究了二氟二草酸硼酸锂(LiODFB)作为锂盐加入到碳酸丙烯酯(PC)+碳酸乙烯酯(EC)+碳酸甲乙酯(EMC)(质量比为1:1:3)混合溶剂中对LiFePO4/石墨电池高温(60 ℃)循环性能的影响. 用线性扫描伏安法(LSV)测试了电解液的电化学窗口. 通过等离子发射光谱(ICP)和能量散射光谱(EDS)对LiFePO4材料高温条件下在不同电解液中的稳定性进行了研究; 并用扫描电镜(SEM)和电化学交流阻抗谱(EIS)分析了石墨负极表面的固体电解液相界面(SEI)膜的热稳定性. 结果表明: 一方面LiODFB基电解液能抑制LiFePO4材料在高温条件下Fe(II)的溶解, 防止溶解的Fe(II)在石墨上还原, 有效地降低电池阻抗; 另一方面, 在LiODFB基电解液中形成的石墨负极表面SEI膜具有更好的热稳定性, 能显著提高LiFePO4/石墨电池的高温循环性能.     

Mn掺杂SnO_2一维纳米结构的制备、形貌及光学性质

用化学气相沉积(CVD)法制备了Mn掺杂的SnO2一维纳米结构(纳米线及纳米带),X射线衍射(XRD)显示样品为金红石型SnO2晶体,其生长机理可分别归结为气-液-固(VLS)和气-固(VS)机理,生长温度和气态原料浓度的差别是造成样品形貌及生长机理不同的主要原因.样品的拉曼谱出现了500、543、694和720cm-1四个新拉曼谱峰,分别是由活性的红外模和表面模引起的.纳米线及纳米带发光峰位于520nm处,发光强度随样品中氧空位的增减出现由强到弱的变化.     

ZrO2表面B2O3的分散及其作用状态

用XPS、FT IR和FT Raman等技术研究了ZrO2表面B2O3的分散及其作用状态,测定了B2O3在ZrO2表面的分散阈值.结果表明：B2O3在ZrO2表面可以三配位BO3和四配位BO4结构单元存在;载体ZrO2的预焙烧温度和硼含量对B2O3的分散及作用状态有较大影响,并改变BO3与BO4结构单元之间的比例.实验测得B2O3在ZrO2载体上的单层分散阈值为0.05 gB2O3/gZrO2（或B2O3的质量分数w=4.76％）,处在此单层中的硼原子以BO4为结构单元直接与ZrO2表面相作用.只有当B2O3的负载量超过此（单层）分散阈值时, BO3结构单元才会形成.     

C60微电极伏安法研究

The microdisk electrode voltammetric behaviors of C_(60) are reported in this communication. This was accomplished by use of a mixed solvent system as Acetonotrile:Xylene=1:4 and a supporting electrolyte as 0.1 mol·L~(-1) Bu_4NPF_6. Au, Pt and Hg (Pt) were used as working electrode. In this new conditions, the successive six step reduction of C60 were obtained at below 15 ℃. It was found that the former five steps are all the single electron reversible reduction, but behaviors of the sixth steps are like EC' processes. Several electrochemical data were determined.     

V2O5/TiO2催化剂表面结构FT-IR发射光谱研究(II)

用傅里哀变换红外发射光谱原位考察了V_2O_5/TiO_2催化剂在制备焙烧过程中担载偏钒酸铵的热分解步骤及其形成的表面活性相结构。偏钒酸铵在200 ℃左右分解, 在300 ℃之前完全转化为晶相V_2O_5。担载于TiO_2上的偏钒酸铵在100 ℃左右与TiO_2已产生强的化学作用, 在200 ℃之前已完全分解。对于10%(质量分数)V_2O_5/TiO_2催化剂其担载偏钒酸分解后在1020 cm~(-1)附近出现晶相V_2O_5的特征峰。但在500 ℃进一步焙烧后晶相V_5O_5的峰减弱并在1025—900 cm~(-1)区出现宽峰, 表明部分晶相V_2O_5可能转化为二维高分散的VO_x物种。2%(质量分数)V_2O_5/TiO_2催化剂在焙烧过程中也显示晶相V_2O_5的弱峰, 但同时也观察到属于VO_x物种的宽峰。进一步降低钒担载量, V_2O_5晶相特征峰逐渐消失, 而在1025—900 cm~(-1)区出现二维VO_x物种的宽峰。结果还表明傅里哀变换红外发射光谱是表征氧化物催化剂表面相结构的一种有力的方法。